Land Rover Discovery Parts

Wiper Arm is the windscreen wiper arm that carries the wiper blade across the windscreen. It mounts to the wiper linkage spindle and transfers the...

Retaining Clip - a fastener for exterior body mouldings and side-step trim. Secures body moulding and side-step trim panels to the bodywork.

Triple Brake Pipe Clip from the brake pipe routing hardware. It retains three rigid brake pipes side by side in one mounting, holding them at a fix...

Screw - M5 x 20 mm fixing screw used to secure the front and rear wheel arch mouldings and the adjoining rear bumper section to the bodywork. A bo...

Bolt securing the front suspension lower control arm at its rear fixing point. M14 x 90mm, Torx drive head.

Goodridge Brake Hose Kit - +2"

Polyurethane Suspension Bush for the front lower suspension arm, rear bush position. The bush locates the rear mounting of the front lower arm wit...

Braided Brake Hose Kit, extended by 150mm, covering the flexible sections of the hydraulic brake circuit between the chassis-mounted brake pipes an...

Shock Absorber Bush Set for the upper damper mounting, polyurethane. The bushes sit in the upper damper mounting, isolating the damper from its mo...

Suspension Arm Nut - M16 flanged nut used on the rear suspension. It secures the lateral and lower arm pivot bolts where they pass through the sus...

Gasket polygon shape type. cover

A-Pillar Finisher - the outer moulding that trims the right-hand A-pillar, part of the exterior body trim. Supplied in satin black, the finisher c...

Rear Axle Breather Pipe vents the rear axle casing. It equalises internal air pressure as the axle heats and cools, allowing the casing to breathe...

Steel hex full nut, M8 x 1.25 thread, catalogued for the clutch and dual-mass flywheel assembly on the Td5 2.5L 5-cylinder turbo diesel engine. Th...

Drag link for the steering linkage, connecting the steering box drop arm to the steering arm on the front axle. The drag link converts the arc des...

Brake Disc for the front axle, solid (non-vented) type. Part of the braking system, the disc provides the friction surface the brake pads clamp ag...

O-Ring - a 22.5 mm sealing ring used in the air conditioning refrigerant circuit. It seals a connection on the condenser and compressor side of th...

M14 x 105mm Bolt is a suspension and steering mounting fastener. It secures the rear suspension arm to the bearing hub, and is also used to mount ...

Nyloc Flanged Nut - M8 flanged nut with a nylon insert, used on front suspension fixings. The nylon collar deforms around the bolt thread as the n...

Fuel Tank Breather Pipe in the fuel tank ventilation system. It vents the fuel tank, relieving pressure and vacuum as the tank fills and empties, ...

Radiator Cowl is the fan cowl mounted to the rear of the radiator on petrol applications. It shrouds the cooling fan to draw air through the radia...

Inline Fuel Filter for carburettor-fed petrol engines, fitted in the low-pressure fuel supply line ahead of the carburettor. It traps rust, scale ...

Coolant Pump Drive Belt for the 2.5L 300TDi turbo diesel engine. It transmits drive from the crankshaft pulley to the coolant pump, driving coolant...

Drain Plug Washer for the transfer box drain and level plugs. The washer seals the plug against the transfer box casing and is replaced each time ...

Banjo Bolt for the turbocharger oil feed pipe on the Td5 engine. This M12 x 1.0mm thread banjo bolt clamps the hollow banjo fitting of the oil sup...

Coil Springs are a matched front pair that raise ride height by 2 inches (50 mm) above standard, forming part of the coil-sprung front suspension. ...

Oil Drain Plug for the ZF transfer box housing. The plug closes the drain and fill port in the transfer box casing, and is removed to drain and re...

Fuel Filler Flap Latch Repair Kit - replacement latch hardware for the fuel filler flap assembly in the rear quarter panel. The flap is held close...

Drive Flange Bolt secures the drive flange to the wheel hub on the axle. Supplied as a set of 10. These bolts are used with the DA1148 and DA1149 ...

Big End Bearing Set — connecting-rod (big-end) bearing shells for the V8 engine bottom end. The shells sit between the connecting-rod big-end bore...

Nyloc Nut - M16 for use in the front axle steering knuckle assembly. This M16 self-locking nut uses a nylon insert to provide prevailing-torque re...

Compressor guard for the air suspension system, part of the underbody protection group. The guard shields the air suspension compressor and its mo...

Fixed Side Steps - body-mounted running boards in the exterior styling and access group. The steps give an intermediate foothold for entry to and ...

Rear Side Window Storage Panels for the load space, supplied as a left- and right-hand pair. The panels fit against the rear side window area of t...

Cylinder Head Bolt Washer seats under the head of a 7/16in cylinder head bolt on the Rover V8 petrol engine. It distributes clamping load across t...

Crown wheel and pinion set with a 4.1:1 final drive ratio for the rear differential, long nose differential configuration. The crown wheel and pin...

Catalytic Converter and Front Pipe Assembly for the V8 petrol exhaust system. It combines the exhaust front pipe (downpipe) with the catalyst, mou...

Oil Pump Seal for the V6 diesel engine oil pump assembly, part of the engine lubrication circuit. It seals the oil pump interface to prevent oil l...

Rear Load Space Parcel Shelf Storage System - an upper-level storage basket for the rear load space. The basket uses the unused height above the l...

Suppressor Capacitor mounted at the ignition coil as part of the ignition system. It suppresses the radio-frequency interference generated by the ...

Exhaust Downpipe with Catalytic Converter - the front section of the exhaust system on V8 petrol applications. It bolts to the exhaust manifold ou...

Air Intake Plenum Extension Moulding in black, the moulded panel that sits in the scuttle area between the rear edge of the bonnet and the base of ...

Fuel Injector - high-pressure common-rail injector for the 2.0L AJ21D4 Ingenium diesel, mid power output. The injector is clamped into the cylinde...

Protector for the fuel pipe system, fitted within the fuel pipes assembly on petrol applications. Used on Defender with 2.8L 6-cylinder BMW M52 pet...

Suspension Kit - Medium Load - +2" Lift is a matched front and rear spring and damper set supplied as a single package, pairing +2" (50 mm) lifted ...

Mainshaft Gear for the LT230 transfer box, 26 teeth, 1.4:1 ratio. This cross-drilled mainshaft gear is an internal component of the LT230 transfer...

Brake Caliper and Actuator - LH for the rear disc brake assembly, supplied complete with its electronic parking brake (EPB) actuator. The caliper h...