Land Rover Freelander Parts

Turbo Drain Gasket for the Td5 turbocharger oil drain. The gasket seals the joint where the oil return (drain) pipe meets the underside of the tur...

Worm-drive Hose Clip with a 32-50 mm clamping range, used to secure a flexible hose to a rigid pipe stub or spigot. Tightening the worm screw draws...

Door Trim Clip for the interior door casing assembly. Fir-tree fastener that secures the door trim casing to the door frame, locating it in the pa...

Injector Sealing Washer seals each fuel injector into the cylinder head within the diesel fuel injection system, for 200 TDi and 300 TDi turbo-dies...

Spire Nut for body-panel fixings - a sprung spring-steel captive nut that clips over a panel edge or into a pierced hole to provide a threaded anch...

Bulb Holder - double-filament bulb holder for an exterior lamp assembly, accepting a 5/21W (P21/5W) twin-filament bulb. The holder seats into the ...

HOLDER - BULB - SINGLE POLE - D1/D2/DEF ALL/F1/P38

Wheel Spanner with a 27 mm socket, a hand tool for removing and refitting wheel nuts. Engages the 27 mm hexagon of the wheel nut to loosen or tigh...

Lock Nut - 7/16" UNF - self-locking nut providing a prevailing-torque fastening. The nut resists loosening under vibration and dynamic load, secur...

Fitment All TD5 diesel models up to (VIN) 6A999999 All TD5 diesel models All V8 EFi petrol models 2.5L 6 Cyl BMW Diesel /4.0L and 4.6L EFI V8 P...

Flanged Locking Nut, M10. General-purpose threaded fastener. The integral flange spreads the clamp load over a wider bearing area, removing the ne...

Flange Bolt, M8 x 50 mm - a hexagon-head bolt with an integral flange beneath the head. The flange spreads the clamping load over a wider bearing ...

Water Pump Seal - sealing ring for the coolant pump within the engine cooling circuit. It forms the coolant-tight joint between the pump and its m...

Filler cap

Amber Side Repeater Lamp, a body-side lamp that repeats the direction indicator signal. The amber lens flashes in time with the front and rear ind...

Fuel Tank Locking Ring for the fuel pump and sender unit assembly. This ring secures the fuel pump and sender unit in the top of the fuel tank, pr...

Headlight Bulb – H4 – 12V 60/55W is a dual-filament halogen headlamp bulb for headlamp units that take the standard H4 fitting. It carries both the...

Flange Bolt is an M8 hexagon flange bolt with a 40 mm shank length. The integral flange beneath the head spreads clamping load over a wider bearin...

Depression control valve assembly TD5 and 2L Freelander

Capless Wedge Bulb, 12V 1.2W, for instrument, facia, clock and cigar-lighter illumination. The glass wedge base pushes directly into the panel hol...

Nut - M24 x 1.5mm is a hexagonal fixing nut with an M24 fine-pitch thread (1.5mm pitch). The 1.5mm fine pitch gives more precise clamping and grea...

Water Pump O-Ring Set provides the sealing rings for the coolant pump, sealing the pump to its mounting face and preventing coolant leakage at the ...

Aluminium Sealing Washer is a soft metal crush washer fitted under a threaded plug or fitting to form a leak-tight joint. When the bolt or plug is...

The Interior Door Card Snap Sac Trim Clips are designed to securely fasten your vehicle's door card and trim pieces. Fitment: all models

Washer Jet Tubing is the flexible hose used within the windscreen washer system, supplied in 1 m lengths. It carries washer fluid from the reservo...

Snap Sac Clip - a push-fit fastener that retains the interior door trim panel (door casing) to the door. The clip locates in the door frame and gr...

Visco Unit Bearing for the rear propshaft, supporting the viscous coupling unit (VCU) in the four-wheel-drive driveline. The bearing locates on th...

Air flow meter TD5 replacement

Self-Tapping Screw – No. 8 × 5/8 in is a general-purpose fastener for securing body, trim and panel fixings. Being self-tapping, it forms its own ...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Stud - M10 x 25mm, a threaded fastening stud used across a range of Land Rover assemblies. The stud provides a fixed threaded mounting point, allo...

Diff mounting Freelander

Exhaust Mount Washer from the exhaust mounting hardware. It seats beneath the fastener at an exhaust mounting point, spreading the clamp load acros...

Clutch Release Bracket mounts within the clutch release mechanism at the gearbox bellhousing, locating and supporting the release components. It p...

Brake Caliper Guide Pin Set for the sliding (floating) disc brake caliper assembly. The guide pins locate the caliper to its mounting bracket and a...

Windscreen Washer Pump An electric pump that draws fluid from the washer reservoir and delivers it under pressure to the washer jets. It press-fits...

Hex Nut, M24 x 1.5mm securing the constant-velocity (CV) joint stub shaft to the wheel hub within the driveline. The nut retains the CV joint and ...

Fuel Pipe Double Clip for routing the fuel lines in the fuel delivery system. Retains a pair of fuel pipes along their run, holding them against t...

Rear Stop and Flasher Lamp for installation in the left-hand position of the rear bumper. This unit provides the stop lamp and direction indicator...

Copper Sealing Washer used to seal a threaded or banjo joint in the fuel and lubrication circuits. The soft copper deforms under tightening to con...

Trim Clip (Scrivet) is a two-piece plastic push-fit fastener used to secure trim panels, facia sections, splash shields and other clipped-in compon...

Cam Cover Gasket for the 1.8L K-Series petrol engine, sealing the camshaft cover to the top face of the cylinder head. It seals the camshaft and v...

Steering Column Shear Bolt securing the steering column mounting clamp to its bracket. The head is designed to shear off once the specified instal...

Wheel Nut for alloy road wheels, part of the wheel mounting assembly. It threads onto the hub stud and clamps against the wheel's nut seat to centr...

Thermostat housing replacement

Radius Arm Bolt secures the rear radius arm (bottom link) at its mounting in the rear suspension. It clamps the link's bush to its bracket, mainta...

Sump Plug for the engine oil sump (oil pan), part of the engine lubrication system. It threads into the drain hole at the base of the sump to seal...