Land Rover Freelander Parts

Bolt - a hexagonal-head bolt with an M10 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the suspe...

Expansion tank cap RRsp, RR3/4, D3, Frl1

Wiper Blade for the rear screen wash/wipe system. Fits the rear wiper arm and sweeps the tailgate glass, operating with the rear wiper motor and w...

Front Differential Oil Seal - a rotary shaft seal fitted to the front differential to retain gear oil and exclude dirt and water where the drive sh...

Inertia Switch in the fuel supply and engine electrical circuit. It cuts electrical power to the fuel pump on a sudden impact or severe deceleratio...

Screw is a fastener used in cooling and heating system assemblies on Land Rover vehicles.

Bulb - 501 is a 12V 5W capless wedge-base bulb, designated W5W. The one-piece glass base pushes directly into the holder, with the contact wires f...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Inlet Manifold Gasket - Lower for the KV6 2.5L V6 petrol engine, sealing the lower inlet manifold to the cylinder head. The gasket maintains an ai...

Cylinder Head Bolt Set for the 1.8L K-Series 4-cylinder petrol engine. The set secures the cylinder head to the block, clamping the head gasket to ...

Flange Bolt - M6 × 10mm is a metric flanged-head fastener used across a wide range of assembly points on Land Rover vehicles. The integrated flang...

Rear Hub Wheel Bearing for the rear hub assembly. It supports the rear wheel hub on the stub axle, allowing the wheel to rotate freely while carryi...

Thermostat O-Ring - K-Series / KV6 is the sealing O-ring for the thermostat housing on the 1.8L K-Series 4-cylinder and 2.5L KV6 petrol engines. I...

Washer is a plain flat washer used as a general-purpose load-spreading fastening component, with a 6 mm internal diameter and a 15 mm outside diame...

Lock Nut secures the tappet adjuster screw on the rocker shaft, holding the valve clearance once it has been set. Tightened against the rocker arm...

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Oil Cooler Pipe for the Freelander 1 fitted with the 2.0L L Series (TCIE) Diesel engine. This pipe carries engine oil from the engine to the exter...

Oil Cooler Pipe for the Freelander 1 fitted with the 2.0L L Series (TCIE) Diesel engine. This pipe forms part of the engine oil cooling circuit, c...

Pipe and Hose Retaining Clip - Engine is a small-bore clip used to retain pipes and hoses at multiple points across the engine bay and fuel system ...

Engine Coolant, pre-mixed for use in the engine cooling system. It circulates through the radiator, water pump and heater circuit to regulate opera...

Flanged Screw - M6 × 12mm is a metric flanged-head fastener used in body, chassis, and electrical component assembly points on Land Rover vehicles....

Oil Filter Gasket for the Rover K-Series 1.8L petrol engine, sealing the oil filter housing to the engine block in the lubrication circuit. This g...

Reverse switch R380 Frl.1 manual

Countersunk Screw - M6 x 12mm is a metric fastener used across multiple assemblies on Land Rover vehicles, including brake disc and drum retention ...

Oil Filler Cap for the engine oil filler neck. Seals the oil filler aperture in the valve cover, preventing oil vapour loss and contamination ingr...

Nut - M10 is an M10 fixing nut for general assembly and repair use across the vehicle. It threads onto an M10 stud or bolt to secure a fastened jo...

Washer - a plain flat washer used as a general-purpose fastening component across many assemblies on the vehicle. Fitted under a bolt head or nut,...

Hose Clip is an adjustable worm-drive band clip that clamps a flexible hose onto its spigot or fitting. It tightens over the hose with a screw-dri...

Connecting Rod Bolt for the engine bottom end, clamping the big-end bearing cap to the connecting rod around the crankshaft journal. Working as a ...

Bolt - M10 x 130mm is a hex-headed metric fastener with a 10 mm nominal thread diameter and a 130 mm shank length. It serves as a general mounting...

Nut An M4 hexagonal plain nut. A general-purpose metric fastener used across a wide range of assemblies. Takes a 7 mm spanner.

Luggage Tie-Down Hook - anchor hook in the luggage compartment for securing loads, integrated with the side trim retainer. Located in the luggage ...

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Wheel Stud for the front and rear axle hubs on the Freelander 1. This stud is pressed into the hub flange and provides the threaded fixing point f...

Finisher Clip - a retaining clip for exterior body finishers and mouldings. The clip secures a trim finisher or moulding to the body panel, engagi...

Indicator Bulb - amber replacement bulb for the exterior indicator lighting circuit. Installs into the indicator lamp housing and provides the amb...

Visco Unit Bearing for the rear propshaft, supporting the viscous coupling unit (VCU) in the four-wheel-drive driveline. The bearing locates on th...

Wheel Brake Cylinder is the rear wheel cylinder of the drum brake assembly. It converts hydraulic pressure from the brake circuit into mechanical ...

Thermostat Housing Gasket seals the joint between the thermostat housing and the engine, preventing coolant leakage at the housing mating face. Fo...

Flanged Nut - M10 flanged fastener. The integral flange spreads the clamping load over a wider area and resists loosening under vibration, removin...

Blade Fuse - 25A for Land Rover electrical systems. This 25A blade fuse protects individual circuits in the vehicle fuse box from overcurrent damage.

Oil Pressure Switch for the V8 petrol engine. The switch monitors oil pressure in the engine lubrication circuit and activates the instrument clus...

Ignition Lead - King The king lead in the high-tension ignition circuit. It carries the high-tension output from the ignition coil to the centre t...

Parking Sensor for the Park Distance Control (PDC) system. This ultrasonic sensor fits into the bumper and transmits and receives ultrasonic pulses...

Cap - Pressure - Radiator

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...