Land Rover Freelander Parts

Rear Brake Shoe Set for the rear drum brake assembly. Each shoe carries a bonded friction lining and is forced outward against the inner face of t...

Handbrake Cable - left-hand cable in the parking brake system. This cable transmits the handbrake lever's travel to the rear brake actuating mecha...

Plain Washer, an M6 flat washer. It fits under the head of an M6 bolt or nut to spread the clamping load over a wider bearing area and protect the...

Gear Lever Gaiter - flexible boot that seals around the gear shift selector rod where it passes through the floor into the transmission tunnel. Th...

Cylinder Block Plug - sealing plug fitted to the cylinder block casting. The plug closes a machined port in the block, sealing the casting so that...

Quarterlight Cap Hinge for the opening rear side window (quarterlight) assembly of the 3-door body. The quarterlight is the hinged rear side glass...

Trim Retention Clip - fastener for securing interior trim and finisher panels. This clip holds interior trim panels - such as pillar post and sill...

Blanking Plug for the clutch bellhousing. It seals an unused aperture in the housing, closing off an opening not required in this configuration and...

Front Brake Calliper Bolt - a fixing within the front brake assembly. This bolt secures the front brake calliper to the hub carrier, clamping the ...

Lock Nut - self-locking threaded fastener used to secure a bolted joint against loosening under vibration. The locking feature maintains clamp loa...

Suspension Arm Bush - rubber bush for the front lower suspension arm. Pressed into the arm's mounting eye, it locates the lower arm at its chassis...

Plain Washer - M12 flat washer used in the rear suspension lower link (bottom link) assembly. Fitted on the M12 bottom-link securing bolt, where i...

Nut (M12) for the front anti-roll bar drop link, serving as the lower securing nut that retains the drop link to the suspension. The drop link con...

Oil Drain Plug for the axle differential housing. Threaded into the lower drain port of the differential casing, it seals the housing in service a...

EGR Valve Filter is a service component of the exhaust gas recirculation (EGR) system, fitted in line with the EGR solenoid control valve. It filt...

Clip — a 6 mm Starlock push-on retaining washer used as a general-purpose fastener across several systems, including exhaust mounting, trim and oth...

Oil Cooler Water Hose for the 2.0-litre four-cylinder diesel engine in non-air-conditioned configuration. It forms part of the engine cooling circ...

CV Joint Boot Kit for the outer constant-velocity joint on the rear drive shaft. The boot seals the outer CV joint, retaining the joint grease and...

Hose Clip for the cooling system, securing coolant and heater hose connections. This clip clamps a hose onto its pipe or stub, holding the joint t...

Freelander lampguard set 4 pcs STC7960 BFA 3001 LG321

Front Lamp Guard Set - protective guards that mount over the front headlamp units as part of the vehicle's exterior protection. The moulded guards...

Rear Door Rubbing Strip - exterior protective moulding fitted along the rear door. It shields the door's paintwork and lower panel edge from minor...

Front Door Rubbing Strip, the protective moulding that runs along the outer face of the front door to guard the bodywork against knocks, scuffs and...

Blanking Plug used to close off an unused port or aperture, sealing the opening against the ingress of dirt, fluid or air.

Intake Manifold Motor for the 2.5 KV6 petrol engine, mounted on the upper inlet manifold to drive the variable induction system (VIS) intake valves...

2-4 Timing Solenoid for the Jatco 5-speed automatic transmission valve body. The solenoid is mounted within the valve body and regulates the hydra...

Idler Pulley for the auxiliary drive belt system of the 1.8L 4-Cylinder K Series petrol engine. The idler runs against the auxiliary drive belt to...

O-Ring elastomer sealing ring used at static joints within the engine assembly, including camshaft and cylinder head cover interfaces, timing gear ...

Fuel Injector O-Ring for diesel applications. The sealing ring at the fuel injector within the fuel injection system. It maintains a leak-tight jo...

Screw, 6 x 26 mm. A threaded fastener used to secure components during assembly.

Fuel Tank Inspection Plate is the access cover that closes the inspection aperture in the floor above the fuel tank. Removing it gives access to t...