Land Rover Freelander Parts

Pedal Pad - Clutch & Brake - moulded rubber pad that fits over the clutch and brake pedal arms in the pedal box. Provides the wear-resistant, ...

O-Ring seals the left-hand output of the Intermediate Reduction Drive (IRD) unit, part of the IRD casing and seal set. It sits at the joint where ...

Coolant Pipe routes coolant to the thermostat within the engine cooling circuit, forming a rigid section of the coolant path to the thermostat hous...

Diff Mounting - RH is the right-hand mounting that locates the rear axle differential to the vehicle body. It carries the differential's reaction ...

Sealing Washer is a copper crush washer used to seal banjo and threaded union joints in the fuel system. Fitted at unions such as the injection pu...

LED Side Repeater is an amber side repeater lamp within the exterior signalling circuit, mounted in the front wing aperture. Each lamp provides la...

CV Joint Circlip - the retaining circlip that secures the constant velocity (CV) joint to the front drive shaft. The circlip locates in a groove o...

Coolant Pipe forms a rigid section of the engine cooling circuit, carrying coolant between connection points on the cooling system. Fitted to the ...

Heater Hose - Outlet is a moulded coolant hose within the heater circuit of the HVAC system. It carries coolant away from the heater matrix outlet...

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Bolt Threaded fastener used within the exhaust system assembly.

Bleed Screw for the hydraulic braking system. This bleed screw (bleed nipple) is fitted to brake calipers or wheel cylinders to allow hydraulic fl...

Plain Washer in M6 oversize form, with a larger outer diameter than a standard M6 washer. It spreads the clamping load of a bolt head or nut over ...

Festoon Bulb for interior lamps. A double-ended festoon bulb that locates between the sprung contacts of the courtesy, map and interior lamp housi...

Screw - a self-tapping pan-head fastener used in interior trim assembly. It cuts its own thread into the panel or moulded mounting boss to secure ...

Oil Seal - Clutch Housing for the manual transmission drivetrain on the Freelander 1. This oil seal is located at the clutch housing and prevents ...

USB Charging Socket - a dashboard-mounted charging socket that fits a standard factory switch aperture, giving a flush, integrated appearance in pl...

Bolt - a hexagonal-head bolt with an M10 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the suspe...

Expansion tank cap RRsp, RR3/4, D3, Frl1

Wiper Blade for the rear screen wash/wipe system. Fits the rear wiper arm and sweeps the tailgate glass, operating with the rear wiper motor and w...

Front Differential Oil Seal - a rotary shaft seal fitted to the front differential to retain gear oil and exclude dirt and water where the drive sh...

EGR Valve to Pipe Gasket for the diesel exhaust gas recirculation (EGR) system. The gasket seals the flanged joint between the EGR valve and the r...

Flange Bolt is an M8 x 35 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Inertia Switch in the fuel supply and engine electrical circuit. It cuts electrical power to the fuel pump on a sudden impact or severe deceleratio...

Front Cover Bolt - M10 flanged hex bolt used to secure the engine front (timing) cover. It also serves as a general-purpose fixing at engine and dr...

Screw is a fastener used in cooling and heating system assemblies on Land Rover vehicles.

Bulb - 501 is a 12V 5W capless wedge-base bulb, designated W5W. The one-piece glass base pushes directly into the holder, with the contact wires f...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Inlet Manifold Gasket - Lower for the KV6 2.5L V6 petrol engine, sealing the lower inlet manifold to the cylinder head. The gasket maintains an ai...

Screw – a black self-tapping screw with a pan head and Pozidriv drive recess, size No. 10 × 5/8 in, used to secure body, trim and panel fixings. B...

Cylinder Head Bolt Set for the 1.8L K-Series 4-cylinder petrol engine. The set secures the cylinder head to the block, clamping the head gasket to ...

Flange Bolt - M6 × 10mm is a metric flanged-head fastener used across a wide range of assembly points on Land Rover vehicles. The integrated flang...

Oil Seal seals the right-hand driveshaft output of the Intermediate Reduction Drive (IRD) unit. The IRD transmits drive from the gearbox to the fr...

Rear Hub Wheel Bearing for the rear hub assembly. It supports the rear wheel hub on the stub axle, allowing the wheel to rotate freely while carryi...

Oil Feed Rail for the 1.8 K-series petrol engine - the strengthened lower ladder rail that bolts to the underside of the cylinder block. It clamps...

Window Regulator - electric regulator forming part of the rear end door glass lifting system. The mechanism converts motor rotation into controlle...

Thermostat O-Ring - K-Series / KV6 is the sealing O-ring for the thermostat housing on the 1.8L K-Series 4-cylinder and 2.5L KV6 petrol engines. I...

Inlet Manifold Gasket for the 1.8L 4-cylinder K Series petrol engine, sealing the inlet manifold to the cylinder head. The gasket maintains an air...

Rear Bumper Lamp - Left-Hand - the near-side rear lamp unit that mounts within the rear bumper, below the main tail lamp cluster, as part of the ve...

IRD Rear Output Flange Oil Seal for the Freelander 1 Intermediate Reduction Drive (IRD) unit. The IRD transfers drive to the rear propshaft and vi...

Top Radiator Hose for the 2.0L Diesel engine cooling circuit. This upper radiator hose connects the engine coolant outlet at the thermostat housin...

Heater Hose - Inlet is a moulded coolant hose within the heater circuit of the HVAC system. It delivers hot coolant from the engine cooling circui...

Radiator Top Hose for the engine cooling system. This upper hose carries hot coolant from the engine's thermostat outlet to the radiator top inlet...

Oil Pressure Switch - tapered thread, engine lubrication circuit. Screws into the oil gallery - at the pump, the filter housing or the oil cooler ...

Washer is a plain flat washer used as a general-purpose load-spreading fastening component, with a 6 mm internal diameter and a 15 mm outside diame...

Radiator Hose Assembly - the coolant hose set for the engine cooling system, connecting the radiator and thermostat housing into the engine cooling...

Washer - a general-purpose fixing washer used across multiple body, brake and chassis assemblies. It spreads the clamping load of a bolt or nut ov...

Flanged Bolt - an M6 x 25mm hexagon-head bolt with an integral flange formed beneath the head. The flange provides a wide bearing face that spread...