Land Rover Freelander Parts

Fuse rated at 15A for the vehicle electrical system. Fitted in the fusebox to protect a circuit rated at 15 amps, the fuse breaks the connection w...

Locking Nut - a push-on locking nut for securing interior trim and ducting. It pushes onto a stud or screw thread and grips to hold the fixing cap...

Lock Nut secures the tappet adjuster screw on the rocker shaft, holding the valve clearance once it has been set. Tightened against the rocker arm...

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Oil Cooler Pipe for the Freelander 1 fitted with the 2.0L L Series (TCIE) Diesel engine. This pipe carries engine oil from the engine to the exter...

Oil Cooler Pipe for the Freelander 1 fitted with the 2.0L L Series (TCIE) Diesel engine. This pipe forms part of the engine oil cooling circuit, c...

Pipe and Hose Retaining Clip - Engine is a small-bore clip used to retain pipes and hoses at multiple points across the engine bay and fuel system ...

Engine Coolant, pre-mixed for use in the engine cooling system. It circulates through the radiator, water pump and heater circuit to regulate opera...

Plastic Drive Rivet - Front Wheel Arch Liner is a push-in fastener used to secure the front wheel arch liner to the surrounding body structure. Fi...

Turbo Drain Gasket for the Td5 turbocharger oil drain. The gasket seals the joint where the oil return (drain) pipe meets the underside of the tur...

Flanged Screw - M6 × 12mm is a metric flanged-head fastener used in body, chassis, and electrical component assembly points on Land Rover vehicles....

Shear Bolt for the steering column lock housing. This tamper-resistant security fixing clamps the steering column lock and ignition switch housing ...

Oil Cooler Hose carries automatic transmission fluid between the gearbox and the transmission oil cooler. It forms part of the transmission coolin...

Anti roll bar link replacement

Oxygen Sensor - Front is the upstream (pre-catalyst) lambda sensor in the exhaust system of the petrol engine. Threaded into the exhaust downpipe ...

Oil Filter Gasket for the Rover K-Series 1.8L petrol engine, sealing the oil filter housing to the engine block in the lubrication circuit. This g...

Cylinder Head Dowel - Plastic is a locating pin fitted at the mating face between the cylinder block and cylinder head in the Td5 2.5L 5-cylinder t...

Instrument Bulb Holder Assembly is a 1.4W instrument panel bulb supplied complete with its integrated holder, forming part of the instrument cluste...

Reverse switch R380 Frl.1 manual

Propshaft Lock Washer, used within the propshaft and viscous coupling assembly. The lock washer is seated beneath the retaining fastener at the pr...

Land Rover Oval Name Badge - exterior identification emblem carrying the Land Rover name in gold lettering on a green ground. Fitted to the front ...

Exhaust Gasket - Front Pipe - sealing gasket for the exhaust manifold-to-front-pipe connection on the Freelander 1 1.8L K Series petrol engine. Fi...

Countersunk Screw - M6 x 12mm is a metric fastener used across multiple assemblies on Land Rover vehicles, including brake disc and drum retention ...

Oil Filler Cap for the engine oil filler neck. Seals the oil filler aperture in the valve cover, preventing oil vapour loss and contamination ingr...

Nut - M10 is an M10 fixing nut for general assembly and repair use across the vehicle. It threads onto an M10 stud or bolt to secure a fastened jo...

Cable Clip - strap-type retaining clip for cable and harness routing. Secures wiring looms or hoses to body panels or chassis members, preventing ...

Washer - a plain flat washer used as a general-purpose fastening component across many assemblies on the vehicle. Fitted under a bolt head or nut,...

Fuel Tank Cradle for the Freelander 1 (1997-2006), providing the structural bracket that secures the fuel tank in position beneath the vehicle chas...

Hose Clip is an adjustable worm-drive band clip that clamps a flexible hose onto its spigot or fitting. It tightens over the hose with a screw-dri...

Connecting Rod Bolt for the engine bottom end, clamping the big-end bearing cap to the connecting rod around the crankshaft journal. Working as a ...

Bolt - M10 x 130mm is a hex-headed metric fastener with a 10 mm nominal thread diameter and a 130 mm shank length. It serves as a general mounting...

Parking Aid Sensor, Rear - ultrasonic transducer for the Parking Distance Control (PDC) system, mounted through the rear bumper cover. This is the ...

Nut An M4 hexagonal plain nut. A general-purpose metric fastener used across a wide range of assemblies. Takes a 7 mm spanner.

Rear Differential Output Oil Seal for the Freelander 1 rear drivetrain. This seal fits at each point where the rear driveshafts exit the rear diff...

Luggage Tie-Down Hook - anchor hook in the luggage compartment for securing loads, integrated with the side trim retainer. Located in the luggage ...

Exhaust Manifold Gasket for the 1.8L 4-cylinder K Series petrol engine, sealing the joint between the exhaust manifold and the cylinder head. The ...

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Oil Filter for the Freelander 1 fitted with the 2.0L L Series Diesel engine. Replaces the engine oil filter as part of a routine oil service. The ...

ABS Pump Relay for the Anti-lock Braking System electrical circuit. A normally open, black-bodied relay that controls power supply to the ABS pump...

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Exhaust Manifold Gasket for the 1.8L K-Series petrol engine, part of the exhaust manifold assembly. It seals the joint between the exhaust manifol...

Wheel Stud for the front and rear axle hubs on the Freelander 1. This stud is pressed into the hub flange and provides the threaded fixing point f...

Differential Mounting - Rear - LH supports the rear differential within the rear final-drive assembly. The mounting locates the left-hand side of ...

Finisher Clip - a retaining clip for exterior body finishers and mouldings. The clip secures a trim finisher or moulding to the body panel, engagi...

Side Indicator is a wing-mounted side repeater lamp in the vehicle's direction-indicator circuit, supplied as a pair. Each unit uses LED elements ...

Indicator Bulb - amber replacement bulb for the exterior indicator lighting circuit. Installs into the indicator lamp housing and provides the amb...

Fits Land Rover Defender models (2007-2016) Clear lens wit orange bulb designed for a sleek, modern look