Land Rover Freelander Parts

Wheel Spanner with a 27 mm socket, a hand tool for removing and refitting wheel nuts. Engages the 27 mm hexagon of the wheel nut to loosen or tigh...

Oil Drain Plug threads into the drain port at the base of the engine sump, sealing the oil pan against leakage during operation. It sits within the...

Relay, a 70A 4-pin grey mini power relay. It provides high-current make-and-break switching for a heavy electrical load, letting a low-current con...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Trim Clip (Scrivet) is a two-piece plastic push-fit fastener used to secure trim panels, facia sections, splash shields and other clipped-in compon...

Steering Column Shear Bolt securing the steering column mounting clamp to its bracket. The head is designed to shear off once the specified instal...

Relay is a 4-pin electromechanical switching relay used within the vehicle's electrical system. A low-current control signal energises the 12V coi...

Festoon Bulb for interior lamps. A double-ended festoon bulb that locates between the sprung contacts of the courtesy, map and interior lamp housi...

Fuel return tube O-ring seal

Fuel Injector Sealing Washer - seals the fuel injector where it seats in the cylinder head. Fitted at the base of the injector, it forms the combu...

Latch hood, bonnet, RH and LH, with sensor

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Exhaust Mounting - Rubber is a rubber isolator in the exhaust suspension system, fitted between the exhaust assembly and the vehicle underbody. Th...

Radiator tank assembly (Use Cap PCD000090/PCD500030)

Inlet valve stem seal for the cylinder head valve train. The seal is pressed onto the inlet valve guide boss and wipes the valve stem as it recipr...

Cylinder Head Cover Gasket for the 2.0L Petrol engine. This gasket seals the cylinder head cover to the cylinder head, containing oil within the v...

Fuel Pump Support Housing Seal seals the mounting interface of the high-pressure fuel pump support housing on 2.0L Si4 petrol engines. The high-pr...

Turbocharger Oil Return Hose Gasket for the 2.0L Si4 TIVCT petrol turbo engine. It seals the joint at the turbocharger oil return (drain) hose, al...

Oil Separator is the crankcase ventilation (PCV) oil separator for the 2.0L 16V turbocharged petrol engine. It sits in the crankcase breather circ...

Connector

Turbocharger Water Inlet Gasket seals the coolant inlet connection at the turbocharger. It fits between the coolant feed union and the turbocharger...

Brake Caliper Guide Pin Dust Cover for the front and rear brake calipers. The boot fits over the caliper guide pin and seals against the carrier b...

Water Pump circulates coolant through the engine cooling system. Driven from the engine, it pumps coolant through the block, cylinder head and rad...

Camshaft is the inlet camshaft for the 2.0L 16V TiVCT turbocharged petrol engine. It operates the intake valves, running in the cylinder head and ...

Throttle Body Assembly for the 2.0L Si4 240PS turbocharged petrol engine, mounted in the air intake tract between the intake ducting and the inlet ...

Oil Cooler dissipates heat from the engine oil to help maintain a stable oil operating temperature. Fitted in the lubrication circuit of the 2.0L ...

Manifold Absolute Pressure (MAP) Sensor mounted on the inlet manifold, part of the engine management system on the 2.0L 16-valve turbocharged petro...

Thermostat and Housing for the 2.0L 16V Ti-VCT petrol engine, supplied complete as a sealed assembly. It sits in the engine cooling circuit and reg...

Timing Chain for the 2.0L 16V TiVCT turbocharged petrol engine (Si4 240PS and Gen2). It forms part of the engine's timing drive, running between th...

Size/Diameter: 433 MHZ door lock frequency

Vacuum Pump Seal - the sealing ring for the engine-mounted vacuum pump. The vacuum pump generates the vacuum used by the brake servo; this seal cl...

Valve Cover Gasket seals the cylinder head cover (rocker cover) to the cylinder head on the 2.0L 16V petrol engine. It forms the oil-tight joint a...

Oil Filter filters the engine oil on the 2.0L 16V turbocharged petrol engine. Part of the oil cooler and filter assembly, it removes contaminants ...

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Portable Jump Starter and Air Compressor - a handheld 12V power pack combining a battery jump starter, power bank, tyre inflator and LED work light...

Wing Mirror Covers are a pair of chromed upper caps for the exterior door mirror assembly. Each cover fits over the upper section of the existing ...