for Discounts / VAT
for Discounts & Correct VAT
Gearbox and transfer box parts for Land Rover and Range Rover, covering ZF automatic units, manual gearboxes, transfer cases, and the seals, bearings, and fluids that keep them running. Stocked across our Dutch warehouse network for EU dispatch, with brands including SKF, Corteco, and Timken.
Split Pin secures a clevis pin or castellated nut by passing through a drilled hole, with its legs splayed back to keep the fastener from working l...
View full details2-4 Timing Solenoid for the Jatco 5-speed automatic transmission valve body. The solenoid is mounted within the valve body and regulates the hydra...
View full detailsOil Cooler Hose - Intermediate forms the middle section of the oil cooler hose run on V8 petrol models fitted with the ZF 4-speed automatic transmi...
View full detailsSpring Pin for the R380 five-speed manual gearbox, located on the mainshaft at the 5th/reverse position. The slotted, sprung-steel pin is driven t...
View full detailsCirclip for the LT77 gearbox mainshaft. This circlip seats in a groove on the mainshaft to retain the mainshaft gears in axial location, holding t...
View full detailsReverse Switch Plunger is a plunger within the LT77 gearbox gearchange assembly that operates the reverse lamp switch. When reverse gear is select...
View full details5th Gear Bias Spring is the gearchange bias spring within the LT77 gearbox shift mechanism. It applies spring load to the selector to bias the gea...
View full detailsThrust Washer locates the reverse idler gear on its shaft within the four-speed gearbox. It fits over the reverse idler shaft and bears against th...
View full detailsNeedle Roller Bearing supports the layshaft within the LT85 five-speed manual gearbox. It carries the layshaft (cluster gear) against the gearbox ...
View full detailsGear Lever Assembly for the R380 five-speed manual gearbox. The lever locates in the gear change remote housing on top of the transmission and pro...
View full detailsGear Lever Assembly for the R380 five-speed manual gearbox. The lever locates in the gear change remote housing on top of the transmission and pro...
View full detailsInhibitor Switch mounts on the ZF automatic transmission. It prevents the engine from cranking unless the selector is in Park or Neutral, and sign...
View full detailsIn/Out Member
Mainshaft - LT95 is the main output shaft of the LT95 four-speed gearbox. It carries the speed gears and synchroniser hubs along its splines, tran...
View full detailsSealing Washer for the oil pump of the automatic transmission. It seals the oil pump's pressure circuit within the automatic transmission, maintai...
View full detailsAutomatic Gearbox Extension Housing Gasket for the rear extension housing of the automatic transmission. It forms the fluid-tight joint where the ...
View full detailsAutomatic Transmission Oil Cooler Return Pipe forms part of the automatic transmission cooling circuit on the 3.5L V8 automatic. It carries cooled...
View full detailsTransmission Oil Pipe - a rigid pipe in the automatic transmission's oil cooling circuit, routing fluid from the gearbox to the transmission oil co...
View full detailsGearbox Spring - the synchroniser spring for the 1st and 2nd gear synchroniser assembly within the five-speed manual gearbox. It maintains tension...
View full detailsOil Cooler Pipe - a rigid pipe in the automatic transmission's oil cooling circuit, carrying fluid between the gearbox and the transmission oil coo...
View full detailsTorque Converter Assembly for the automatic transmission. It forms the fluid coupling between the engine flexplate and the gearbox input shaft, tra...
View full detailsLayshaft Gear - a gear from the layshaft, or countershaft, cluster of the LT77 five-speed manual gearbox. The layshaft runs beneath the mainshaft ...
View full detailsGear Change Selector Cable forms part of the manual gearchange linkage, connecting the gear lever to the gearbox selector mechanism. When the driv...
View full detailsGear Selector Lever Button for the automatic transmission selector lever. The push button in the selector lever that releases the detent, allowing...
View full detailsReverse Gear Assembly is the reverse idler gear that runs on the layshaft of the LT77 five-speed manual gearbox. When reverse is selected, the idl...
View full detailsGearbox Oil Screen Filter mounts inside the oil pan of the ZF 6HP26 six-speed automatic transmission, forming the suction-side filter of the hydrau...
View full detailsGear Selector Fork - selector fork in the gear shift assembly of the MT82 six-speed manual gearbox. The same fork serves two positions in the shif...
View full detailsLayshaft is the countershaft of the R380 five-speed manual gearbox. It carries the constant-mesh gear cluster, transmitting drive from the input s...
View full detailsMainshaft for the R380 five-speed manual gearbox, carrying the output-side gears and transmitting drive to the transmission output. Replaces the w...
View full detailsR380 Mainshaft Spacer for the R380 5-speed manual gearbox. The spacer locates on the mainshaft (the gearbox output shaft) within the main gear clus...
View full details3rd/Reverse Gear - a mainshaft gear within the LT95 four-speed gearbox, providing the third-speed and reverse gear ratios in the transmission gear ...
View full detailsTransmission Filter
Gear
Gear Lever Gaiter for the manual transmission gear shift assembly. It fits over the base of the gear lever where it passes through the transmission...
View full detailsShim - 1.20 mm front axle hub shim. Fitted in the front axle hub assembly to set the correct spacing and control end-float within the half-shaft a...
View full detailsCluster Gear for the LT77 five-speed manual gearbox, part of the layshaft geartrain. The cluster carries the constant-mesh gears that run continuo...
View full detailsReverse Idler Gear Assembly for the LT77 five-speed manual gearbox. Provides the reverse gear train, reversing mainshaft rotation for reverse driv...
View full details2nd Gear is a constant-mesh gear wheel within the LT77 five-speed manual gearbox. It provides the second forward gear ratio, meshing with its matc...
View full detailsInterlock Spool Selector interlock spool within the manual gearbox gear-selection mechanism. Prevents more than one gear from being selected at on...
View full detailsTransfer Box Repair Kit - a bearing and seal overhaul set for the DD295 transfer box. The kit renews the internal bearings and oil seals when rebu...
View full detailsCluster Gear (layshaft gear cluster) for the LT77 5-speed manual gearbox, to military specification. The cluster gear runs on the layshaft and car...
View full detailsGear - Transfer Case Actuator is a replacement drive gear for the transfer case shift actuator motor. The actuator motor drives high and low range...
View full detailsAutomatic Transmission Fluid for ZF 6HP Series Transmissions, supplied in a 1-litre bottle. This fluid is formulated from a blend of hydrocracked ...
View full details5th Speed Gear for the R380 5-speed manual gearbox, 37 teeth. This is the mainshaft member of the fifth-gear pair. It runs against the 5th speed c...
View full detailsMainshaft for the LT76 four-speed manual gearbox. The mainshaft is the gearbox output shaft, carrying the main gear cluster and transmitting drive ...
View full detailsFifth Speed Gear - 19-tooth 5th driven gear for the R380 five-speed manual gearbox. Mounts on the mainshaft and meshes with the layshaft to provid...
View full details5th Speed Gear for the LT77 five-speed manual gearbox in V8 applications. The 85mm driven gear for fifth speed, running on the gearbox mainshaft t...
View full detailsInsulatorfloor 6 Speed Man ZF S6-53
Category Overview
Every Land Rover and Range Rover uses a two-part driveline: a main gearbox that handles gear ratios and torque delivery, and a transfer box that splits drive between the front and rear axles for the brand's 4x4 traction. Both are serviceable assemblies and both are made up of parts that wear, leak, or fail individually long before the unit itself needs replacing. This collection covers the seals, bearings, synchros, gaskets, fluids, and rebuild components for the gearboxes and transfer cases fitted across the Defender, Discovery, Range Rover, Freelander, and Series ranges.
For most owners the right approach is component replacement, not unit replacement. A leaking output seal, a worn bearing, or contaminated fluid are repairable faults. Knowing which fault you have, and which part fits your specific gearbox or transfer case, is the difference between a straightforward fix and an expensive misdiagnosis.
ZF Automatic GearboxesModern Land Rover and Range Rover models run almost exclusively on ZF automatic transmissions. The ZF 6HP26 sits in the Range Rover L322, Range Rover Sport L320, and Discovery 3 and 4. The ZF 8HP series followed it across the Range Rover L405, Range Rover Sport L494, Range Rover L460, Range Rover Sport L461, and Discovery 5.
These gearboxes are precision hydraulic-mechatronic units. The valve body, torque converter, and electronic control module are the most common failure points, usually triggered by degraded fluid rather than mechanical wear. Symptoms such as delayed engagement, gear hunting, or harsh shifting on a warm gearbox typically point to valve body or fluid condition, not to a failing transmission.
For service work on these units, ZF specifies ZF Lifeguard Fluid 6 (6HP series) or ZF Lifeguard Fluid 8 (8HP series). The two fluids are not interchangeable. ZF's official position on 8HP service intervals is "fill for life", but independent transmission specialists across Europe recommend a precautionary fluid and pan-filter service at around 80,000 to 120,000 km on vehicles used for towing, urban driving, or high-mileage motorway work. For the technical detail on fluid specifications and service requirements, ZF Aftermarket publishes its own transmission oil reference guide.
Confirm the ZF gearbox code on your vehicle before ordering fluid or service kits. ZF Lifeguard Fluid 6 and Lifeguard Fluid 8 are different specifications, and using the wrong grade is the most common cause of valve body wear after a DIY service.
Manual gearboxes are less common on current production but are still the dominant powertrain across the Classic Defender, early Discovery, Freelander 1, and the Series range. The R380 was the long-running five-speed unit fitted to the Discovery 1 (post-200Tdi production), Discovery 2, and Classic Defender from the 300Tdi through to early Td5. The MT82 six-speed replaced it on the Defender 2.4 and 2.2 TDCi Puma. Earlier production used the LT77 (Discovery 1 200Tdi era) and the LT76 and LT95 on Series 2/3 vehicles.
These units fail in predictable ways. Synchroniser rings on second and third gear wear first. Input shaft and lay shaft bearings degrade with age and oil contamination. Selector linkages and detent springs cause the symptoms most often misdiagnosed as a gearbox fault. Reverse idler gear chatter is common on R380 units past 240,000 km.
For most manual-gearbox owners, parts-level repair is straightforward and rebuild kits are available for the R380, LT77, and MT82. Specific Freelander 1 parts (IB5 manual) sit under the Freelander 1 collection. Series 2/3 gearbox parts have their own fitment requirements covered under the Series 2 and 3 collection.
Transfer BoxesThe transfer box carries as much load as the gearbox and is often the part that goes ignored until it fails. The LT230 is the dominant transfer case across the Classic Defender, Discovery 1, Discovery 2, Range Rover Classic, and P38. It uses gear-drive between input and output shafts and a chain-drive system to the front output. The Discovery 3 and Discovery 4 use a chain-drive Magna Steyr unit with an electronic shift system. Modern Range Rover and Range Rover Sport models on the L405, L494, L460, and L461 platforms use a ZF-integrated transfer case as part of the transmission assembly.
Common failures are output shaft seal leaks, chain stretch on chain-drive units (Magna Steyr and modern ZF), viscous coupling failure on units fitted to early Discovery 2 and Range Rover P38, and selector motor failure on electronic-shift cases.
Transfer box fluid is not the same specification as gearbox fluid on most Land Rover and Range Rover units. The LT230 takes EP90 (or the Land Rover-specified MTF94 on later units), and the Magna Steyr unit on Discovery 3 and 4 takes a specific ATF spec. Confirm before ordering.
Most gearbox parts returns are caused by ordering errors at the buying stage rather than parts faults. The following are the most common we see across the Land Rover and Range Rover range.
For parts that overlap with the clutch system on manual gearboxes, see the Land Rover clutch parts collection. For driveline parts forward and aft of the gearbox, see the driveshaft and propshaft parts collection.
Technical GuidesIn-depth diagnostic and component guides for the gearbox-adjacent failure modes that come up most often on Land Rover and Range Rover models.
Technical breakdown of the L494's 3.0 TDV6 timing chain issues, air suspension faults, and ZF 8HP wear patterns. Covers what fails, why it fails, and which parts the workshop will need.
Range Rover Sport L494 ZF 8HP guideHow to tell drivetrain noise apart from gearbox or transfer box noise, and which parts to inspect before ordering. Covers Discovery 4, Freelander 2, and Series 3 driveline symptoms.
Land Rover driveline diagnosis guideClutch faults are routinely misdiagnosed as gearbox faults due to overlapping symptoms. This guide explains how to identify the real fault before replacing parts.
Land Rover clutch diagnosis guideThe gearbox controls gear ratios and torque delivery from the engine; the transfer box splits drive between the front and rear axles for 4x4 traction and also provides the low-range gearing on Defender and Discovery models. Both are serviceable assemblies and both fail in distinct ways. Drivetrain symptoms can come from either, which is why most Land Rover gearbox parts returns are caused by mis-diagnosis rather than mis-fit.
ZF 6HP26 transmissions (fitted to Range Rover L322, Range Rover Sport L320, Discovery 3, and Discovery 4) take ZF Lifeguard Fluid 6. ZF 8HP transmissions (fitted to Range Rover L405, L460, Range Rover Sport L494 and L461, and Discovery 5) take ZF Lifeguard Fluid 8. The two fluids are not interchangeable. Confirm the gearbox code stamped on the casing before ordering.
ZF's official position on the 8HP series is fill-for-life. In practice, independent transmission specialists across Europe recommend a precautionary fluid and pan-filter service at around 80,000 to 120,000 km, particularly on vehicles used for towing, frequent urban driving, or high-mileage motorway work. The 6HP26 typically receives a service interval at 90,000 km. Manual gearboxes (R380, MT82, LT77) take a gear oil change at approximately 60,000 km.
The LT230, fitted to the Classic Defender, Discovery 1, Discovery 2, Range Rover Classic, and Range Rover P38, fails in three main ways: output shaft seal leaks (often caused by flange wear behind the seal), input gear bearing wear, and selector linkage faults that mimic gearbox symptoms. Most LT230 issues are repairable with component-level parts rather than a full transfer case replacement.
The R380 five-speed manual was fitted to the Discovery 1 (post-200Tdi), Discovery 2, and Classic Defender from the 300Tdi era through to early Td5 production. The LT77 preceded the R380 on the Discovery 1 200Tdi. The MT82 six-speed replaced the R380 on the Defender 2.4 and 2.2 TDCi Puma. Rebuild kits and individual components for all three are stocked in this collection.
Yes. Most Land Rover transmission service jobs touch both units, particularly fluid changes, seal replacements, and bearing kits. Ordering both at the same time reduces vehicle downtime and is the most common workshop order pattern.