Land Rover Gearbox & Transferbox Parts

Hex-head bolt, 7/16" UNF thread, 1-1/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and soc...

Gearbox Tunnel Insulation Pad - heat and sound insulation pad fitted to the gearbox tunnel around the gear lever. For manual transmission applicat...

Plug Washer for the drain and filler/level plugs on the LT95 gearbox and differential. The washer seats between the threaded plug and the casing t...

Gearbox Mounting - left-hand transmission rubber mounting for the 2.5L 300 TDi diesel. This rubber-to-metal mounting supports the gearbox on the l...

Gear Lever Grommet for the 5-speed manual gearchange assembly. It seals around the gear lever where it passes through the housing, sealing out dra...

Differential Thrust Washer for the LT230 transfer box centre differential. It bears against the differential gears within the centre differential,...

Mainshaft Bearing supports the mainshaft within the LT230 transfer box, carrying the shaft's rotational loads and keeping it running true as drive ...

O-Ring - Gear Change Selector seals the gear change selector shaft where it enters the transmission housing, preventing lubricant leakage at the sh...

Oil Seal for the front cover of the LT85 five-speed manual gearbox. It seals the front cover where the primary (input) shaft enters the gearbox, re...

Drain Plug for the gearbox, transfer box and axle casings. It threads into the drain point at the base of the casing to retain the oil in service, ...

In/out member spring

Shim plate

Bottom cover seal

Collar Bush for the four-wheel-drive selector mechanism in the two-speed transfer box. It seats on the high-range 4WD selector rod, locating the s...

First Gear Bush for the LT76 gearbox mainshaft. The bush journals the mainshaft first gear, providing the running surface on which the gear turns o...

Oil Temperature Sender for the engine oil temperature gauge circuit. The sender threads into the oil gallery and carries a temperature-sensitive re...

Taper Roller Bearing - shaft bearing for the R380 five-speed manual gearbox. A taper roller bearing carries both radial load and axial thrust, loc...

Sealing Plug for the transmission handbrake drum on the LT95 four-speed gearbox. The drum-type transmission handbrake acts on the transfer box out...

Clutch Slave Cylinder, part of the hydraulic clutch release circuit. The slave cylinder receives fluid pressure from the clutch master cylinder an...

Automatic Transmission Filter for the ZF automatic gearbox fluid circuit. It sits in the transmission fluid pan and filters the ATF drawn up into t...

Transfer Box Output Mud Shield Shield that fits over the transfer box output flange to protect the output shaft oil seal from mud, water and debris...

lock washer. sold EACH.

Needle Roller Bearing for the transfer box intermediate gear. The bearing carries the intermediate gear on its shaft within the gear cluster, allo...

Bolt is an M8 x 80 mm threaded fastener used to clamp two components together at a bolted joint. It is tightened into a threaded hole or secured w...

Nut - M8 plain low-profile nut, sold individually. A standard metric M8 nut in the low-profile (thin) form. Used across gearbox, suspension, axle,...

Alloy Gear & Transfer Box Knobs Machined alloy replacement knobs for the main gear lever and the transfer box lever, supplied as a matching pai...

O-Ring seals the left-hand output of the Intermediate Reduction Drive (IRD) unit, part of the IRD casing and seal set. It sits at the joint where ...

Intermediate shaft lock nut LT230

Gearbox Bearing for the R380 5-speed manual gearbox, measuring 35 × 72 mm. Fitted within the R380 transmission assembly, this rolling-element bear...

Kickdown Cable Assembly for the automatic transmission control. The cable links the throttle to the automatic gearbox, relaying throttle position s...

Gearbox Sump Gasket for the ZF 4-speed automatic transmission, sealing the joint between the transmission oil pan (sump) and the gearbox casing. T...

Transfer Box Lever Lock Nut used to secure the selector linkage at the transfer case. This half nut (thin profile locking nut) threads onto the sel...

Drive Flange is a torque-transmitting flange fitted to the manual gearbox output. It provides the bolted coupling that carries drive from the gear...

External Circlip for the R380 manual gearbox selector yoke. The circlip locates in the groove on the selector yoke and retains it in position with...

Seat yoke

Gear Selector Ball End is the ball-joint pivot in the gear change selector linkage, connecting the selector rod to the transmission operating shaft...

Gearbox Gasket seals the top cover to the main casing of the LT77 five-speed manual gearbox, forming an oil-tight joint between the top cover plate...

Gearbox Gasket seals the transfer box side cover joint on the LT85 five-speed manual gearbox, forming an oil-tight seal between the side cover and ...

Oil Seal - Clutch Cross Shaft for Series 1 and Series 2 Land Rover vehicles (1948-1971). The clutch cross shaft passes through the bellhousing and...

Gearbox Gasket for the LT76 four-speed gearbox with integral transfer assembly. It seals a mating housing face within the gearbox and transfer cas...

Gear Lever Retaining Plate for the gear lever turret on the LT76 manual gearbox. The plate bolts over the base of the gear lever to retain it in i...

Front Cover Bolt - M10 flanged hex bolt used to secure the engine front (timing) cover. It also serves as a general-purpose fixing at engine and dr...

Flange Bolt - M10 x 35mm flanged hex bolt used at a range of driveline and engine mounting points, including bell housing, flywheel and clutch, tra...

Dowel is a precision locating pin used to align mating components in the drivetrain, such as the bell housing, gearbox casing and flywheel or drive...

Bellhousing Grommet is the rubber grommet that seals an aperture in the clutch bellhousing. It closes the opening in the bellhousing casing to kee...

Oil Seal - Clutch Housing for the manual transmission drivetrain on the Freelander 1. This oil seal is located at the clutch housing and prevents ...

Transmission Selector Switch for the Discovery 2 automatic gearbox. This switch monitors the position of the gear selector lever and signals the t...

Dowel - Bell Housing Alignment in the gearbox/engine interface assembly. This dowel locates the bell housing accurately relative to the engine blo...