Land Rover Hardware & Fasteners

Gearbox Gasket for the LT76 four-speed gearbox with integral transfer assembly. It seals a mating housing face within the gearbox and transfer cas...

Manifold Clamp - a clamping plate that secures the manifold to the cylinder head. It fits over the manifold flange and draws down onto the cylinde...

Differential Pinion Bearing Spacer used in the axle differential assembly across a broad range of Land Rover models from 1965 onwards. This spacer...

Hoodstick Bracket Clamp - secures a hoodstick to its mounting bracket within the soft-top frame. The clamp holds the hoodstick (the soft-top frame...

Banjo bolt

Oil Pump Lock Tab, part of the engine oil pump assembly. The lock tab is a tab washer fitted under the oil pump retaining fastener; once the faste...

Split Pin locks slotted nuts, clevis pins and linkage joints against loosening, passing through a drilled hole and splayed to retain the assembly. ...

Bolt, 7/16" BSF x 1-3/8" secures the upper swivel pin to the swivel housing in the front axle assembly. The top swivel pin retains the swivel ball...

Circlip Retaining circlip for the gearbox rear output shaft. It seats in a machined groove on the output shaft, locating the adjacent component ax...

Wing Fixing Plate is a two-stud captive stud plate used in the front body mounting assembly, where it secures the front wing to the radiator (front...

Wing Fixing Plate is a three-stud captive stud plate used in the front body mounting assembly, where it secures the front wing to the radiator (fro...

Designed for use with heavy-duty steering arms, this kit provides the necessary brackets and hardware for a solid fitment, enhancing steering stabi...

Nut - M8 plain low-profile nut, sold individually. A standard metric M8 nut in the low-profile (thin) form. Used across gearbox, suspension, axle,...

Bolt is an M8 x 80 mm threaded fastener used to clamp two components together at a bolted joint. It is tightened into a threaded hole or secured w...

Caliper Bolt is the fixing bolt that secures the brake caliper to its mounting bracket. The same bolt specification is used across several chassis...

Safari Door Bolt Kit - a stainless steel fixing set for the rear safari (third) door, for Non-Puma applications. The bolts secure the fixings of t...

High-Tensile Bolt with a 5/16" UNF (Unified National Fine) imperial thread and a 1-1/4" shank length. A hex-head fastener manufactured to a high-t...

Bolt - V8 Inlet Manifold is the fastener that secures the inlet manifold on the Rover V8 petrol engine. It clamps the inlet manifold to the cylind...

Dowel is a precision locating pin used to align mating components in the drivetrain, such as the bell housing, gearbox casing and flywheel or drive...

Screw is a fastener used in cooling and heating system assemblies on Land Rover vehicles.

Heater Knob Screw for the heater control assembly. This screw secures a control knob to its spindle on the heater control panel.

Screw - a self-tapping pan-head fastener used in interior trim assembly. It cuts its own thread into the panel or moulded mounting boss to secure ...

Camshaft Cover Grommet sealing the camshaft cover to the cylinder head on the Td5 2.5L five-cylinder turbo diesel engine. The grommet forms a stat...

Inlet Manifold Seal sealing the inlet manifold to the cylinder block valley on the V8 petrol engine. This formed seal closes the manifold valley j...

Edge Clip - push-on edge clip that grips the flange of an interior trim panel, retaining both the panel and the wiring harness routed along its edg...

Seat Mounting Plates for the seat installation assembly, supplied as a pair. These plates provide the fixed interface between the seat base frame ...

Front door hinge fixing kit used within the body door hinge mounting assembly. The kit provides the required fasteners and mounting components to...

Cable Tie for securing wiring harnesses and cable runs throughout the vehicle.

Aluminium Pop Rivet, a blind rivet used as a general fixing for body panels, interior trim and seat-mounting brackets. It is set with a rivet gun: ...

Bolt - a hexagonal-head bolt with an M10 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the suspe...

Rivet - a mechanical fastener used within the body and chassis assembly to join thin sheet metal and panel components. Nominal size 3/16" (4.8 mm)...

Reverse lamp switch LT85 V8

Shock Absorber Washer - Rear - a retaining washer used at the rear suspension shock absorber mounting. It seats against the lower shock absorber b...

Bolt - a hexagonal-head bolt with an M6 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the vehicl...

Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M5 thread with a 1...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Hex Bolt - a hexagonal-head bolt with an M6 metric thread and a 12 mm length, manufactured to property class 8.8. Class 8.8 is a medium-carbon ste...

Bolt is a general-purpose imperial-thread fixing with a 5/16-inch UNC (Unified Coarse) thread and a 7/8-inch length. Used as a common fastener acr...

Hex Head Bolt, M10 x 30 mm. A metric hex head bolt with a 10 mm thread diameter and 30 mm shank length, used as a general fixing across a range of...

Spring Washer for the fuel tank sender unit and fuel pick-up pipe fixings. Fitted beneath the retaining screws that secure the fuel gauge sender u...

Taper Roller Bearing - outer pinion bearing in the differential final drive assembly. The drive pinion is carried on a pair of opposed taper rolle...

Tailgate Seal for the lower edge of the rear tailboard. It seats along the bottom of the drop-down tailgate and seals against the body, keeping wa...

Door Sill Seal rubber weatherseal for the lower edge of the rear side door aperture, left-hand side. The seal runs along the sill of the door fram...

Oil Seal Retainer is the plate that retains the swivel oil seal on the front axle. It bolts to the swivel housing and clamps the swivel oil seal ag...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Bleed Screw for the hydraulic braking system. This bleed screw (bleed nipple) is fitted to brake calipers or wheel cylinders to allow hydraulic fl...

Starlock Washer - a push-on retaining washer used to secure components onto plain shafts and rods without the need for threading or tools. Once pr...

Plain Washer in M6 oversize form, with a larger outer diameter than a standard M6 washer. It spreads the clamping load of a bolt head or nut over ...