Land Rover Hardware & Fasteners

Body Panel Locknut for square-hole panel apertures, used in body, interior, and trim panel assemblies. This push-fit captive nut locates into a sq...

Hylomar Hylosil 100 is a neutral-curing RTV silicone sealant for gasketing, sealing and bonding in automotive and engineering applications. It cure...

Hylomar Universal Blue is a non-setting gasket jointing compound for use on gaskets and machined metal joint faces in automotive and engineering ap...

Spring Washer fitted under a nut or bolt head to resist loosening from vibration. An M8 split-ring (single-coil) spring washer. The sprung opening...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Door Casing Stud for the interior door casing assembly. Locating stud onto which the door casing mounts, retaining the trim panel and holding it i...

Worm-drive Hose Clip with a 32-50 mm clamping range, used to secure a flexible hose to a rigid pipe stub or spigot. Tightening the worm screw draws...

Door Trim Clip for the interior door casing assembly. Fir-tree fastener that secures the door trim casing to the door frame, locating it in the pa...

Oil Cooler Pipe O-Ring for engine and transmission oil cooling circuits. This O-ring seals pipe fitting and hose connection joints in the oil cool...

Lock Nut - 7/16" UNF - self-locking nut providing a prevailing-torque fastening. The nut resists loosening under vibration and dynamic load, secur...

Copper Sealing Washer for banjo bolt connections in the engine oil circuit. This copper washer seats against the machined face of a banjo fitting ...

Spire Nut for body-panel fixings - a sprung spring-steel captive nut that clips over a panel edge or into a pierced hole to provide a threaded anch...

Flanged Locking Nut, M10. General-purpose threaded fastener. The integral flange spreads the clamp load over a wider bearing area, removing the ne...

Flange Bolt, M8 x 50 mm - a hexagon-head bolt with an integral flange beneath the head. The flange spreads the clamping load over a wider bearing ...

Water Pump Seal: sealing ring for the coolant pump (Land Rover description 'Seal-coolant pump'). Used in the Td5 coolant pump installation, also i...

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

Nut - M24 x 1.5mm is a hexagonal fixing nut with an M24 fine-pitch thread (1.5mm pitch). The 1.5mm fine pitch gives more precise clamping and grea...

Aluminium Sealing Washer is a soft metal crush washer fitted under a threaded plug or fitting to form a leak-tight joint. When the bolt or plug is...

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

Flanged Screw, M8 x 20mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washe...

Flange Bolt is an M8 hexagon flange bolt with a 40 mm shank length. The integral flange beneath the head spreads clamping load over a wider bearin...

The Interior Door Card Snap Sac Trim Clips are designed to securely fasten your vehicle's door card and trim pieces. Fitment: all models

Self-Tapping Screw – No. 8 × 5/8 in is a general-purpose fastener for securing body, trim and panel fixings. Being self-tapping, it forms its own ...

Snap Sac Clip - a push-fit fastener that retains the interior door trim panel (door casing) to the door. The clip locates in the door frame and gr...

Brake Pipe Clip – Double secures a pair of brake pipes along their routing through the braking hydraulic circuit, retaining both lines against the ...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Stud - M10 x 25mm, a threaded fastening stud used across a range of Land Rover assemblies. The stud provides a fixed threaded mounting point, allo...

Flange Bolt, M12 - a hexagon-head bolt with an integral flange beneath the head. The flange spreads the clamping load over a wider bearing area an...

Fastener clip

Trim Clip is a plastic fastener used to secure interior and exterior trim panels, finishers and wheelarch liners to the body. It pushes into a pre...

Steering Column Shear Bolt securing the steering column mounting clamp to its bracket. The head is designed to shear off once the specified instal...

Nyloc Nut with an M8 thread - a nylon-insert locking nut used as a self-locking fastener in threaded assemblies. A nylon collar set into the top o...

Trim Clip (Scrivet) is a two-piece plastic push-fit fastener used to secure trim panels, facia sections, splash shields and other clipped-in compon...

Bolt for the brake caliper carrier. Secures the caliper carrier bracket to the hub on disc-brake assemblies, retaining the carrier against braking ...

Fuel Pipe Double Clip for routing the fuel lines in the fuel delivery system. Retains a pair of fuel pipes along their run, holding them against t...

Hex Nut, M24 x 1.5mm securing the constant-velocity (CV) joint stub shaft to the wheel hub within the driveline. The nut retains the CV joint and ...

Exhaust Mount Washer from the exhaust mounting hardware. It seats beneath the fastener at an exhaust mounting point, spreading the clamp load acros...

Flanged Head Screw is an M6 x 12mm machine screw with an integral flange beneath the head. The flange spreads clamping load over a wider area and ...

Copper Sealing Washer used to seal a threaded or banjo joint in the fuel and lubrication circuits. The soft copper deforms under tightening to con...

Transfer Box Casing Seal for the transfer box (transfer case) assembly within the drivetrain. It seals the joint between the transfer box casing s...

Oil Filler Seal seals the oil filler cap against the filler neck on the camshaft (rocker) cover. It sits between the cap and the cover opening, ke...

Locking Nut - an M12 self-locking nut used to secure suspension linkage fasteners. The locking feature resists loosening under the vibration and c...

Sump Plug for the engine oil sump (oil pan), part of the engine lubrication system. It threads into the drain hole at the base of the sump to seal...

Bolt M8 X 16 HTSETS 8.8 S/COL sold EACH

Window Regulator - electric regulator forming part of the rear end door glass lifting system. The mechanism converts motor rotation into controlle...

Radius Arm Bolt secures the rear radius arm (bottom link) at its mounting in the rear suspension. It clamps the link's bush to its bracket, mainta...

Sealing Washer is a copper crush washer used to seal banjo and threaded union joints in the fuel system. Fitted at unions such as the injection pu...

Screw is a fastener used in cooling and heating system assemblies on Land Rover vehicles.