Land Rover Hardware & Fasteners

Nyloc Nut with a 3/8" UNF thread, used to secure propshaft flange bolts. A nylon insert set into the crown of the nut deforms over the bolt thread...

Propshaft Bolt - a fastener that secures the propshaft universal-joint flange to the differential drive flange within the driveline. It clamps the...

Brake Caliper Bolt - M12 x 35mm threaded fastener securing the brake caliper to its mounting on the hub carrier. It holds the caliper in correct a...

Hylomar Hylosil 100 is a neutral-curing RTV silicone sealant for gasketing, sealing and bonding in automotive and engineering applications. It cure...

Injector Sealing Washer seals the base of the fuel injector into the cylinder head on the Td5 2.5L 5-cylinder turbo diesel engine. The washer sits...

Nyloc Nut with a 3/8" UNF thread and a 12 mm across-flats hex, in the full-height (thick) form. A nylon insert set into the crown of the nut defor...

Nyloc Nut with an M20 thread, used across suspension and driveline flange fastenings. A nylon insert set into the crown of the nut deforms over th...

Hylomar Universal Blue is a non-setting gasket jointing compound for use on gaskets and machined metal joint faces in automotive and engineering ap...

Exhaust Gasket - V8 for the exhaust downpipe assembly on V8 petrol engines. This gasket seals the flange joint at the exhaust downpipe, maintainin...

Fir Tree Fastener in light grey, for the roof trim and headlining assembly. Push-fit fastener that secures roof trim panels and headlining ancilla...

Door Casing Stud for the interior door casing assembly. Locating stud onto which the door casing mounts, retaining the trim panel and holding it i...

Copper Sealing Washer for the oil drain plug of the LT77 and R380 manual gearboxes. The washer forms a leak-free seal between the drain plug and t...

Split Pin locks a castellated (slotted) nut in place, passing through the nut slots and a cross-drilled hole in the shaft to stop the nut working l...

Clutch Clip - Push Rod to Lever for the hydraulic clutch actuation system. This spring clip secures the clutch slave cylinder push rod to the clut...

Oil Cooler Pipe O-Ring for engine and transmission oil cooling circuits. This O-ring seals pipe fitting and hose connection joints in the oil cool...

Sump Drain Plug Washer - sealing washer for the engine sump drain plug on the Td5 2.5L 5-cylinder turbo diesel engine. This washer seats between t...

Nyloc Nut with an M10 thread - the nylon-insert locking nut used on U-bolt fixings. A nylon collar set into the top of the nut grips the bolt thre...

Filler Plug sealing the fill and bleed point of the engine cooling system, fitted to the thermostat housing and the radiator. O-ring is included. ...

Fuel Connector Block Gasket for the Td5 2.5L five-cylinder diesel engine, sealing the fuel connector block to the engine within the fuel pressure r...

O-Ring for the LT230 Transfer Box, used at multiple sealing positions within the unit. This O-ring is fitted at several locations in the LT230 two...

Inlet Manifold Gasket for the Td5 2.5L five-cylinder diesel, sealing the inlet manifold to the cylinder head. The gasket forms the air-tight joint...

Wheel Nut - Hex for the road wheel mounting assembly. This hexagonal nut secures the road wheel to the hub, clamping the wheel against the hub fac...

Oil Cooler O-Ring for the 2.5L Td5 5-Cylinder Turbo Diesel engine. This O-ring seals the oil cooler assembly and oil filter housing to the cylinde...

Water Pump Gasket Seals the coolant pump to the engine within the cooling system of the Rover V8 petrol engine. It forms a coolant-tight joint bet...

Oil drain plug TD5

Spire Nut for body-panel fixings - a sprung spring-steel captive nut that clips over a panel edge or into a pierced hole to provide a threaded anch...

Felt Washer for the output shaft assemblies of the LT230 transfer box. This washer is fitted at the front and rear output flanges of the LT230, wh...

Cylinder Head Bolt securing the cylinder head to the cylinder block and clamping the head gasket joint. It maintains the clamping force that seals...

Inlet Manifold Seal for the V8 petrol induction system, straight pattern. The seal closes the joint between the underside of the inlet manifold an...

Cylinder Head Dowel for the Td5 2.5L 5-cylinder turbo diesel engine. The dowel locates between the cylinder block and the cylinder head, aligning ...

Trim Retention Clip for securing door casing and bodyside trim panels. This push-fit clip engages a panel stud on the door inner frame or body str...

Copper Sealing Washer for banjo bolt connections in the engine oil circuit. This copper washer seats against the machined face of a banjo fitting ...

Wiper Clip A retaining clip within the windscreen wiper assembly that secures the wiper blade to the wiper arm, holding the blade in place on the arm.

Anchor Stud providing a threaded fixing point for interior trim panels, door casings, carpet sections, and air intake duct components. This stud a...

Clutch Fork Insert is the nylon insulator that fits over the clutch fork pivot pin inside the bellhousing, cushioning the fork at its fulcrum point...

Nut - M6 is a plain M6 hexagonal nut used as a general-purpose threaded fastener throughout the chassis, body and mechanical assemblies. It tighte...

Brake Disc Fixing Screw that secures the brake disc to the wheel hub. The screw locates and retains the disc against the hub face during assembly,...

Flanged Locking Nut, M10. General-purpose threaded fastener. The integral flange spreads the clamp load over a wider bearing area, removing the ne...

Clip

LT230 Intermediate Shaft O-Ring, sealing the intermediate shaft within the LT230 two-speed transfer box main casing. The intermediate shaft transm...

Nyloc Nut - M16 flanged self-locking nut used at suspension link fastenings. The integral flange spreads the clamp load across the joint face and ...

Clutch Fork Clip secures the clutch arm rod to the release fork inside the gearbox bellhousing on LT77, LT85, and R380 5-speed manual gearboxes. T...

Pop Rivet (blind rivet) for fastening panels, trim and brackets where access is only available from one side. The rivet is fitted into a drilled h...

Joint washer

Propshaft Bolt Kit - Rear is a driveline fixing set for securing the rear propeller shaft at its flange connections. The kit provides the correct-...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Upper Spring Isolator for the coil spring suspension. This rubber seat sits at the upper end of the coil spring, between the top of the spring and ...

Water Pump Seal - sealing ring for the coolant pump within the engine cooling circuit. It forms the coolant-tight joint between the pump and its m...