Land Rover Hardware & Fasteners

Salisbury Joint Washer for the Salisbury rear axle differential. The gasket seats between the differential carrier and the axle casing, sealing th...

Door Trim Clip for the interior door casing assembly. Fir-tree fastener that secures the door trim casing to the door frame, locating it in the pa...

Transfer Box Gear Lever Knob fitted to the LT230 transfer box gear lever in vehicles where the LT230 is paired with the LT77 main gearbox. The lev...

Spire Clip used to retain front wing panels and heater assembly components. This spring-steel clip slides over a screw or stud thread and grips se...

U-Bolt Nut - 7/16 BSF for use in the leaf spring suspension assembly. U-bolts clamp the leaf spring pack to the axle casing at the front and rear ...

Clutch Clip - Push Rod to Lever for the hydraulic clutch actuation system. This spring clip secures the clutch slave cylinder push rod to the clut...

Oil Cooler Pipe O-Ring for engine and transmission oil cooling circuits. This O-ring seals pipe fitting and hose connection joints in the oil cool...

Swivel Pin Gasket seals the joint between the swivel pin housing and the axle case on the front axle. It sits at the mating face where the swivel ...

Brake Union Nut - Metric Thread for the hydraulic brake pipe circuit. This union nut seals and secures brake pipe connections at the unions throug...

Sump Drain Plug Washer - sealing washer for the engine sump drain plug on the Td5 2.5L 5-cylinder turbo diesel engine. This washer seats between t...

Exhaust Bush - Male is the male-profile rubber mounting bush used in the exhaust system vibration isolation assembly. This bush pairs with the cor...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Nyloc Nut with an M10 thread - the nylon-insert locking nut used on U-bolt fixings. A nylon collar set into the top of the nut grips the bolt thre...

Front Hub Lock Washer for the front hub and driveshaft assembly. This tabbed washer seats between the hub nut and the hub bearing assembly on the ...

Split Pin for use in the front and rear suspension assembly of the Series Land Rover. The split pin is inserted through the hole in a castle nut o...

Axle Key Washer for the hub nut locking system in the axle assembly. This tab washer seats beneath the axle hub nut, with tabs that locate into ma...

Grommet

Power steering seal kit

Filler Plug sealing the fill and bleed point of the engine cooling system, fitted to the thermostat housing and the radiator. O-ring is included. ...

Oil Seal Retainer for the front axle swivel housing assembly. This retaining plate holds the swivel housing oil seal square against the chrome swiv...

Water Pump Inlet Gasket - seals the water pump inlet housing against the engine front cover within the coolant circuit. It forms the joint between...

Fuel Connector Block Gasket for the Td5 2.5L five-cylinder diesel engine, sealing the fuel connector block to the engine within the fuel pressure r...

Thermostat Housing Gasket Seals the thermostat housing to the cylinder head within the cooling system of the 300 TDi 2.5L turbo diesel engine. It ...

Bolt, M10 x 45 securing the front drive member to the hub. The drive member transmits torque from the axle shaft to the road wheel, and these bolts...

Suspension and Chassis Mounting Bolt used across multiple suspension and chassis linkage positions. This hexagon bolt secures components including...

Bolt - fixing bolt with an ACME (trapezoidal) thread form, used to secure the outer front wing to the bulkhead. It fastens the rear mounting flang...

Sealing Washer used at sealing interfaces across multiple engine assembly groups. This washer is used in rocker cover and breather assemblies, val...

Brake Pipe Clip - single-bore retaining clip for securing a rigid brake pipe to the chassis or body structure. This clip holds the brake pipe in i...

Anti-Roll Bar Washer used at the anti-roll bar and shock absorber mounting. The washer spreads the clamping load of the retaining nut across the m...

Brake Pipe Clip - Double secures and routes rigid hydraulic brake pipes within the braking system. This double clip retains two brake pipes at a s...

Oil Filter Gasket for the engine lubrication system, sealing the oil filter bowl to the filter housing on 4-cylinder petrol and diesel engines. Th...

Clip is a multi-purpose retaining clip used to secure cables, harnesses and small components in their mountings. It locates and holds items such a...

O-Ring for the LT230 Transfer Box, used at multiple sealing positions within the unit. This O-ring is fitted at several locations in the LT230 two...

Inlet Manifold Gasket for the Td5 2.5L five-cylinder diesel, sealing the inlet manifold to the cylinder head. The gasket forms the air-tight joint...

Flanged Screw, M8 x 25 mm. A metric set screw with an integral flange beneath the hexagon head that spreads clamping load and helps resist loosenin...

Lock Nut - 7/16" UNF - self-locking nut providing a prevailing-torque fastening. The nut resists loosening under vibration and dynamic load, secur...

Transfer Box Gear Change Bush for the LT230 transfer box gear change and differential lock linkage. This bush fits the gear change linkage connect...

Radius Arm Bolt - hexagon head bolt securing the rear radius arm at the axle and chassis mounting points within the rear suspension assembly. This...

Oil Cooler O-Ring for the 2.5L Td5 5-Cylinder Turbo Diesel engine. This O-ring seals the oil cooler assembly and oil filter housing to the cylinde...

Door Hinge Bolt for attaching door hinges to the body structure. This countersunk bolt secures the hinge plate to the hinge assembly, providing a ...

Exhaust Bush - Female is the female-profile rubber mounting bush used in the exhaust system vibration isolation assembly. This bush pairs with the...

Rocker cover rubber washer petrol

Water Pump Gasket Seals the coolant pump to the engine within the cooling system of the Rover V8 petrol engine. It forms a coolant-tight joint bet...

Oil drain plug TD5

Lock Washer for the gearbox mainshaft, securing the special retaining nut where the mainshaft meets the transfer box. A tab washer whose tang is b...

Shim hinge

Fuel Pump Gasket for the 2.0L diesel engine (Series II) and 2.25L diesel engine (Series IIA). This gasket seals between the mechanical fuel pump b...

Self-Locking Nut with a 5/16" UNF thread and a 1/2" across-flats hexagon. The self-locking action resists loosening under vibration, retaining cla...