Land Rover Hardware & Fasteners

Gearbox Plug Sealing Washer for LT76 and LT77 manual gearbox drain, level, and inspection plugs. This sealing washer fits beneath the thread of ge...

Captive Nut with a UNF thread, providing a fixed threaded anchor point for a bolted fixing. The nut is retained in its bracket or panel so it cann...

Felt Washer for the output shaft assemblies of the LT230 transfer box. This washer is fitted at the front and rear output flanges of the LT230, wh...

Cylinder Head Bolt securing the cylinder head to the cylinder block and clamping the head gasket joint. It maintains the clamping force that seals...

Track Rod Clamp is a split-tube collar that secures the threaded track rod end into the track rod tube on the front steering axle. Once the front ...

Hinge Pin Kit containing the replacement hardware for door and rear tailgate hinges on Series and early Defender models. Fits the front and rear d...

Bolt - 3/8" BSF x 1" hexagonal head bolt to British Standard Fine thread specification. 3/8" BSF (British Standard Fine) thread with a 1" shank le...

Nut, 1/2" UNF. A threaded fastener used on the early 4-cylinder diesel engine assembly.

Front Hub Lock Washer located within the Front Hub & Driveshaft Assembly, securing the hub bearing retaining nut in position. The lock washer ...

Screw with a 1/4" UNF (Unified Fine) thread, 7/8" long, used as a setscrew in body, hinge and mirror-arm fixings. Note: non-metric (imperial UNF) ...

Inlet Manifold Seal for the V8 petrol induction system, straight pattern. The seal closes the joint between the underside of the inlet manifold an...

Fitment: All models to (VIN) KA930455 All models 1980 on

Cylinder Head Dowel for the Td5 2.5L 5-cylinder turbo diesel engine. The dowel locates between the cylinder block and the cylinder head, aligning ...

Panhard Rod Bolt - a metric hexagon-head bolt measuring M14 x 80mm, used to secure the Panhard rod within the axle location. The Panhard rod locat...

Copper Sealing Washer for banjo bolt connections in the engine oil circuit. This copper washer seats against the machined face of a banjo fitting ...

Elbow Gasket seals the coolant outlet elbow, or thermostat housing, to the inlet manifold on the V8 petrol engine, forming part of the engine cooli...

Nyloc Nut - 1/4" UNF - self-locking nut with a nylon insert set into the collar. The nylon insert grips the bolt thread to resist loosening under ...

Anchor Stud providing a threaded fixing point for interior trim panels, door casings, carpet sections, and air intake duct components. This stud a...

Clutch Fork Insert is the nylon insulator that fits over the clutch fork pivot pin inside the bellhousing, cushioning the fork at its fulcrum point...

Hex Nut - 1/4" UNF is a plain hexagonal nut with a 1/4 inch UNF thread, used as a general-purpose imperial-thread fastener throughout the chassis, ...

Nut - M6 is a plain M6 hexagonal nut used as a general-purpose threaded fastener throughout the chassis, body and mechanical assemblies. It tighte...

Bonnet Hinge Bolt Kit - a set of stainless steel fixings for mounting the bonnet hinges that allow the bonnet to pivot open. The kit secures the h...

Door Casing Trim Clip is a fir-tree push-fit fastener used in the interior door trim assembly to retain the door casing panel against the door fram...

Nyloc Nut - M14 - self-locking nut with a nylon insert set into the collar. The nylon insert grips the bolt thread to resist loosening under vibra...

Flanged Locking Nut, M10. General-purpose threaded fastener. The integral flange spreads the clamp load over a wider bearing area, removing the ne...

Clip

LT230 Intermediate Shaft O-Ring, sealing the intermediate shaft within the LT230 two-speed transfer box main casing. The intermediate shaft transm...

Gearbox Filter for the LT77 five-speed manual gearbox. This gauze oil strainer sits in the gearbox lubrication circuit, screening the oil drawn thr...

Flange Bolt securing the rear output (propshaft) drive flange to the output shaft of the LT230 transfer box. Manufactured to a high-tensile specif...

Fuel Lift Pump Gasket seals the mechanical fuel lift pump to the engine on 2.5L diesel applications, including the 200TDi and 300TDi. Fitted betwe...

Brake Hose Clip in the brake hydraulic circuit, securing a flexible brake hose to its mounting bracket where the hose crosses from the chassis to a...

Nyloc Nut - M16 flanged self-locking nut used at suspension link fastenings. The integral flange spreads the clamp load across the joint face and ...

Speedometer Cable Plate Screw secures the speedometer cable retaining plate to the gearbox. It clamps the plate that holds the speedometer drive c...

Clutch Fork Clip secures the clutch arm rod to the release fork inside the gearbox bellhousing on LT77, LT85, and R380 5-speed manual gearboxes. T...

Water Pump Gasket - 7-Hole for the cooling system on Land Rover 4-cylinder military engines. This gasket seals the mating face between the water p...

Engine Plug (3/8 BSF thread) for Land Rover 4-cylinder petrol and diesel engines. This threaded blanking plug is used at multiple points across th...

Escutcheon Seal for the exterior door handle escutcheon. The seal sits between the handle escutcheon and the outer door skin, sealing the aperture...

Differential flange 4-spline

Nut - a plain full hex nut with a 3/8" BSF (British Standard Fine) thread. A general-purpose imperial fastener used at many points across the engi...

Door Latch - Rear - Anti-Burst is the latching mechanism for the rear end door, operating within the body closure system. It mounts to the rear do...

Washer Pump for the windscreen washer system, running on a 24-volt electrical supply. The pump draws fluid from the washer reservoir and delivers ...

Pop Rivet (blind rivet) for fastening panels, trim and brackets where access is only available from one side. The rivet is fitted into a drilled h...

Joint washer

Compression Olive for rigid fuel pipe unions. This 8 mm ferrule seats between the union nut and the fitting body, compressing onto the pipe as the ...

Oil Seal Housing Gasket for the 300 TDi engine, sealing the rear crankshaft oil seal housing to the rear face of the cylinder block. The gasket fo...

Gasket

Water Pump Gasket seals the coolant pump to the engine front cover on the V8 petrol engine. It fits at the pump mounting face, sealing the coolant...

Drain Plug - a tapered threaded plug used to seal and drain fluid from engine and driveline housings. It serves as a coolant drain plug in the cyl...