Land Rover Hardware & Fasteners

Drain plug LT77 R380

Flange Bolt is an M8 hexagon flange bolt with a 40 mm shank length. The integral flange beneath the head spreads clamping load over a wider bearin...

Injector Sealing Washer seals the base of the fuel injector into the cylinder head on the Td5 2.5L 5-cylinder turbo diesel engine. The washer sits...

O-Ring sealing the front crankshaft (timing) sprocket within the timing case of the 2.5L 300TDi turbo diesel engine. It forms an oil-tight seal ar...

Head Gasket Seals the cylinder head to the cylinder block on the pre-TDi 2.25L and 2.5L naturally aspirated and turbocharged diesel engines. It co...

Link Clip - an anti-rattle clip for the side door latch linkage. It retains the latch operating rod within the door lock mechanism, holding the li...

Top Link Bolt - 3/4 UNF x 4 inch hexagon head bolt for securing the front top link (upper radius arm) at the fulcrum and ball joint mounting points...

Anti-Rattle Clip secures the linkage rod within the door latch and lock mechanism. It retains the lock linkage rod at its connection point, holdin...

Caged Nut securing the front door hinge to the body pillar. The nut is held in a floating sheet-metal cage that retains it against the panel and l...

Grille Screw – Black secures the front grille panel to its surrounding bodywork. The black finish matches the grille and adjacent trim, giving a d...

Self-Tapping Screw – No. 8 × 1/2 in is a general-purpose fastener used across body, trim and electrical fixings, such as lamp guards, wheelguards, ...

Inlet Manifold Stud with a UNF thread. Threads into the cylinder head to mount the inlet manifold, taking the manifold nut that clamps the manifol...

Swivel Pin Shim, 0.010" thick, fitted at the front axle swivel pin housing. The shim is placed beneath the swivel pin (king pin) to set the correc...

Swivel Pin Shim, 0.005" thick, fitted at the front axle swivel pin housing. The shim is placed beneath the swivel pin (king pin) to set the correc...

Pedal Pin is the pivot pin in the pedal box assembly that locates the brake and clutch pedals. It passes through the pedal boss and the pedal moun...

Barrel Lock with Key A lock barrel (cylinder) supplied complete with its key, forming the keyed locking element of the door lock assembly. The bar...

Mounting stud

Hexagon Nut with a 7/16" BSF (British Standard Fine) thread. A standard nut cut to the British Standard Fine thread form used throughout the fixin...

Castle Nut - M12 castellated nut used on the steering and suspension ball-joint fixings. Its slotted crown takes a split pin through the drilled h...

Brake pad fitting kit for STC1277

Bolt - a hexagonal-head bolt with a 3/8" UNF (Unified Fine) imperial thread and a 1" length. Used as a suspension and chassis fixing at points such...

Set Screw, M8 x 70 mm. A fully threaded hexagon-head fastener in high-tensile steel with a bright zinc-plated finish. Used across a range of chassi...

Grease Nipple is a long-thread lubrication fitting with a UNF thread form, used to deliver grease into propshaft universal joints and sliding splin...

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

Front Propshaft Flange Bolt Kit - the high-tensile fasteners that secure the front propshaft to its mating flanges at the transfer box and axle end...

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Shock Absorber Mounting Washer (inner), used at pin-type shock absorber mountings within the suspension damper installation. It seats on the mount...

The Interior Door Card Snap Sac Trim Clips are designed to securely fasten your vehicle's door card and trim pieces. Fitment: all models

Thermostat Gasket for the Td5 2.5L 5-cylinder turbo diesel engine, sealing the coolant outlet elbow to the thermostat housing. It forms the coolan...

Hex-head bolt, 1/4" UNF thread, 7/8" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socket...

Seal

Camshaft Oil Seal seals the camshaft on the 2.5L 4-cylinder diesel engines, including the 200TDi. Fitted at the front of the engine where the cams...

Washer 20mm

Flanged Bolt, M10 x 30 mm. A metric bolt with an integral flange beneath the hexagon head that spreads clamping load over a wider area and helps re...

Heater (Glow) Plug Ballast Resistor for the diesel pre-heat circuit. Wired in series with the heater plugs, the resistor drops the battery supply t...

Brake Pipe Clip (double) for ABS-equipped braking systems, used to route and secure rigid brake pipes. The double form holds two brake pipes side ...

Double Pipe Clip for the fuel delivery system. This clip locates and retains a pair of parallel fuel pipe runs in a single fixing, holding the feed...

Window Filler Strip is a body weather-sealing trim for the side (quarter) window aperture, closing the gap between the fixed window glass and the s...

Flanged Nyloc Nut, M10, a multi-purpose locking fastener used across the chassis and suspension. The nylon insert resists loosening under vibratio...

Fuel Pipe Clip securing fuel pipe within the fuel delivery system. The clip retains and locates the fuel line along its routing, holding it agains...

Core Plug (Cup Type) for sealing the core holes left in the engine block casting after the sand cores are removed during manufacture. The cup-shap...

Head Bolt Kit - a complete set of cylinder head bolts for the Rover V8 engine, securing the cylinder heads to the block and clamping the head gaske...

Loadspace Mat Retainer for the rear door aperture at the tailboard. The retainer is a profiled strip that clamps the rear door weatherseal and the...

Gearbox-Transfer Box Gasket for the LT76 gearbox, sealing the mating joint between the gearbox and the transfer box. The gasket maintains the oil-...

Tab Washer for the steering drop arm retaining nut on the Adwest steering box. Fitted beneath the drop arm nut on the steering box output shaft, t...

Wheel Stud for the axle hub - 16mm pull-in type. Mounts in the hub flange to carry the road wheel, which is clamped by the wheel nut running on th...

U-Bolt for the leaf spring suspension, clamping the front leaf spring to the axle. This is the short, round-top type with a 7/16" BSF thread. It p...