Land Rover Hardware & Fasteners

Core Plug for the cylinder head, sealing a core hole left in the casting during manufacture. It closes the opening left by the casting sand core a...

Windscreen Hinge Bolt is a fixing used to secure the folding windscreen frame hinge to the scuttle. It clamps the hinge mounting at the base of th...

Steering Box Joint Washer - 0.005" selective shim washer used within the steering box. Fitted at the steering box joint face, this shim sets the c...

Lock Nut with a 5/16" BSF thread. The lock nut secures a threaded fastening against loosening under vibration, maintaining clamp load in service. ...

Sealing Washer - copper sealing ring for the cooling system drain points. It seats under the radiator drain plug and the cylinder block drain tap, ...

Door Bolt Kit - a stainless steel fixing set for the four side doors (Non-Puma applications). The kit comprises M8 countersunk Allen-head bolts, J...

Plain Washer with a 6 mm (1/4") bore, a general-purpose flat washer for use with M6 fasteners. Fitted beneath a bolt head or nut to spread the cla...

Plain Washer - a flat, load-spreading washer with a 1/4 in (6 mm) bore and 5/8 in outside diameter, approximately 1/16 in thick, finished in Sherar...

Nyloc Nut with an M16 thread - a nylon-insert locking nut used on heavily loaded suspension and driveline fixings. A nylon collar set into the top...

Hex-head bolt, 5/16" UNC thread, 1" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and socke...

Tab Washer locks the drop arm retaining nut on the Adwest power steering box, its tab folded against a flat on the nut to stop it working loose und...

Lokut Nut is a self-locking nut used to secure the headlamp to the body at the front wing. The self-locking design resists loosening under vibrati...

Set Screw, a hexagon-head metric fastener, M10 x 25mm. In Land Rover terminology a set screw is a bolt threaded along its full length rather than ...

Screw M6 x 20 pan-head screw. It can be used in place of LR083229 (RYG500650 / DYP500210 / EYG50080) but is not identical: this screw has no capti...

Bolt, a hexagon-head fastener with a 5/16" UNF thread, 7/8" long. This imperial fastener is of the UNF (Unified National Fine) thread series and i...

Speedo cable oil seal retainer plate

Driving Member (front hub drive flange) for the front axle hub assembly. It bolts to the outer face of the hub and engages the splined end of the f...

Suspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...

Spring ring

Locking Nut Clip - a grey spire nut clip that pushes onto a panel edge and receives a self-tapping screw. It gives a captive threaded fixing point...

Injector Clamp Bolt for the Td5 2.5L 5-cylinder turbo diesel engine. It secures the injector clamp to the cylinder head, holding the fuel injector ...

Fir Tree Clip - a push-fit fastener that secures the door casing (interior door trim panel) to the door. The ribbed, tapered fir-tree stem pushes ...

Thermostat Housing Gasket for the 200TDi 2.5L turbo-diesel engine, sealing the thermostat housing to the cylinder head within the engine cooling ci...

Anti-Roll Bar Bolt Protector for the rear suspension. It fits over the rear anti-roll bar mounting strap and its retaining bolt, shielding the fixi...

Bolt 1/4" UNF x 7/8" is a fixing bolt for the track rod and steering damper within the steering linkage. It clamps the track rod end and secures t...

Aluminium Sealing Washer is a soft metal crush washer fitted under a threaded plug or fitting to form a leak-tight joint. When the bolt or plug is...

Screw – Facia is a No. 6 × 1/2 in self-tapping screw used to secure the facia panel assembly, including the cowl instrument binnacle and the upper ...

Screw – a No. 6 × 1/2 in self-tapping screw used to secure interior trim and panel fixings, such as the instrument binnacle, fascia mouldings and a...

Brake Pipe Clip – Double secures a pair of brake pipes along their routing through the braking hydraulic circuit, retaining both lines against the ...

Brake pipe clip

Clutch Release Bush for V8 petrol applications, located within the clutch assembly at the rear of the crankshaft. The bush seats in the spigot rec...

Exhaust Saddle Clamp for securing exhaust pipe sections to underbody mounting brackets in the exhaust system. The U-shaped saddle body seats over ...

Exhaust Clamp Plate for the exhaust mounting assembly. Three-hole clamping plate that secures the exhaust pipe within the mounting bracket assembl...

Heater control cable clip (Heating / Heater Controls)

Rear Crossmember Bolt Kit - a set of stainless steel fixings for securing the rear crossmember to the chassis. The rear crossmember is the rearmos...

Lock Nut is a captive plastic fastener (commonly known as a Lokut nut) that receives a No. 10 self-tapping screw. The body pushes into a square pa...

Hex-head bolt, 3/8" UNC thread, 1-1/8" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and so...

Hub Cap closes the centre of the front hub drive flange, covering the driveshaft coupling bolts within the front axle hub assembly. This version c...

A-frame Ball Joint Fitting Kit – the mounting hardware for the rear A-frame ball joint and its housing. The fixings secure the ball-joint housing t...

Front Bumper Tapping Block and Bolt Set for securing the front bumper, comprising the tapping block and the associated bolt set. The tapping block...

Contact Set - Lucas Distributor is the breaker-point set for the ignition distributor. Mounted on the distributor baseplate, the points are opened...

Anti-roll bar bush

Castle Nut (castellated nut) used to retain halfshafts, output shafts and differential pinion shafts in Land Rover axle and drivetrain assemblies. ...

Bumper Bolt Set in stainless steel - the fixing kit that secures the front bumper to the chassis front cross-member. This kit includes 4 x M10 x 1...

Fir Tree Fastener push-in fixing in grey, used to retain headlining, roof trim and similar interior and exterior trim panels. The tapered fir-tree...

Screw used as a securing fastener in the pedal box area and in brake pipe routing. This screw retains the cover plate at the top of the pedal box,...

Hex-head bolt, 5/16" UNF thread, 3/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socke...

Output Shaft Oil Seal seals the output shaft of the LT95 four-speed gearbox and integral transfer box, retaining gear oil where the shaft passes th...