Land Rover Hardware & Fasteners

Window Regulator - electric regulator forming part of the rear end door glass lifting system. The mechanism converts motor rotation into controlle...

Radius Arm Bolt secures the rear radius arm (bottom link) at its mounting in the rear suspension. It clamps the link's bush to its bracket, mainta...

Nut - M8 plain low-profile nut, sold individually. A standard metric M8 nut in the low-profile (thin) form. Used across gearbox, suspension, axle,...

Bolt is an M8 x 80 mm threaded fastener used to clamp two components together at a bolted joint. It is tightened into a threaded hole or secured w...

Screw is a fastener used in cooling and heating system assemblies on Land Rover vehicles.

Screw - a self-tapping pan-head fastener used in interior trim assembly. It cuts its own thread into the panel or moulded mounting boss to secure ...

Bolt - a hexagonal-head bolt with an M10 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the suspe...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Bleed Screw for the hydraulic braking system. This bleed screw (bleed nipple) is fitted to brake calipers or wheel cylinders to allow hydraulic fl...

Plain Washer in M6 oversize form, with a larger outer diameter than a standard M6 washer. It spreads the clamping load of a bolt head or nut over ...

Cylinder Head Bolt Set for the 1.8L K-Series 4-cylinder petrol engine. The set secures the cylinder head to the block, clamping the head gasket to ...

Rear Hub Wheel Bearing for the rear hub assembly. It supports the rear wheel hub on the stub axle, allowing the wheel to rotate freely while carryi...

Pipe and Hose Retaining Clip - Engine is a small-bore clip used to retain pipes and hoses at multiple points across the engine bay and fuel system ...

Flange Bolt - M6 × 10mm is a metric flanged-head fastener used across a wide range of assembly points on Land Rover vehicles. The integrated flang...

Front Cover Bolt - M10 flanged hex bolt used to secure the engine front (timing) cover. It also serves as a general-purpose fixing at engine and dr...

Flange Bolt is an M8 x 35 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Thermostat O-Ring - K-Series / KV6 is the sealing O-ring for the thermostat housing on the 1.8L K-Series 4-cylinder and 2.5L KV6 petrol engines. I...

Washer is a plain flat washer used as a general-purpose load-spreading fastening component, with a 6 mm internal diameter and a 15 mm outside diame...

Flanged Bolt - an M6 x 25mm hexagon-head bolt with an integral flange formed beneath the head. The flange provides a wide bearing face that spread...

Bolt Threaded fastener used within the exhaust system assembly.

Screw – a black self-tapping screw with a pan head and Pozidriv drive recess, size No. 10 × 5/8 in, used to secure body, trim and panel fixings. B...

Washer - a general-purpose fixing washer used across multiple body, brake and chassis assemblies. It spreads the clamping load of a bolt or nut ov...

Countersunk Screw - M6 x 12mm is a metric fastener used across multiple assemblies on Land Rover vehicles, including brake disc and drum retention ...

Cable Clip - strap-type retaining clip for cable and harness routing. Secures wiring looms or hoses to body panels or chassis members, preventing ...

Propshaft Lock Washer, used within the propshaft and viscous coupling assembly. The lock washer is seated beneath the retaining fastener at the pr...

Thermostat Housing Gasket seals the joint between the thermostat housing and the engine, preventing coolant leakage at the housing mating face. Fo...

Hose Clip is an adjustable worm-drive band clip that clamps a flexible hose onto its spigot or fitting. It tightens over the hose with a screw-dri...

Luggage Tie-Down Hook - anchor hook in the luggage compartment for securing loads, integrated with the side trim retainer. Located in the luggage ...

Flanged Screw - M6 × 12mm is a metric flanged-head fastener used in body, chassis, and electrical component assembly points on Land Rover vehicles....

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Connecting Rod Bolt for the engine bottom end, clamping the big-end bearing cap to the connecting rod around the crankshaft journal. Working as a ...

Lock Nut secures the tappet adjuster screw on the rocker shaft, holding the valve clearance once it has been set. Tightened against the rocker arm...

Plastic Drive Rivet - Front Wheel Arch Liner is a push-in fastener used to secure the front wheel arch liner to the surrounding body structure. Fi...

Wheel Stud for the front and rear axle hubs on the Freelander 1. This stud is pressed into the hub flange and provides the threaded fixing point f...

Bolt - M10 x 130mm is a hex-headed metric fastener with a 10 mm nominal thread diameter and a 130 mm shank length. It serves as a general mounting...

Nut - M10 is an M10 fixing nut for general assembly and repair use across the vehicle. It threads onto an M10 stud or bolt to secure a fastened jo...

Locking Nut - a push-on locking nut for securing interior trim and ducting. It pushes onto a stud or screw thread and grips to hold the fixing cap...

Finisher Clip - a retaining clip for exterior body finishers and mouldings. The clip secures a trim finisher or moulding to the body panel, engagi...

Nut An M4 hexagonal plain nut. A general-purpose metric fastener used across a wide range of assemblies. Takes a 7 mm spanner.

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Washer - a plain flat washer used as a general-purpose fastening component across many assemblies on the vehicle. Fitted under a bolt head or nut,...

Banjo Bolt for the turbocharger oil feed pipe on the Td5 engine. This M12 x 1.0mm thread banjo bolt clamps the hollow banjo fitting of the oil sup...

Wheel Nut for steel road wheels on the Freelander 1. Standard fastener securing the steel road wheel to the hub. Sold individually.

Rivet Screw - 6.3 x 22mm for securing panels and trim on Land Rover vehicles. This scrivet-type fastener combines a screw thread with a expanding ...

Oil Cooler Housing End Cap - LH - the left-hand end cap that closes the engine oil cooler housing on the 2.0 L Series diesel. The oil cooler housi...

Rear Lower Adjusting Link for the rear suspension. The link connects the rear hub carrier to the subframe as part of the lower suspension linkage....

Conrod