Land Rover Interior Parts

Bulkhead Vent Hinge Pin Kit in stainless steel - replaces the pivot pins on which the bulkhead (scuttle) air vent flaps hinge. The original steel ...

Front Floor Contour Mat Kit is a pair of shaped rubber mats for the front cabin footwells, forming part of the interior floor protection. Each mat...

Transfer Lever Knob in yellow, for the four-wheel-drive engagement lever on the transfer gearbox. It threads onto the top of the selector lever an...

Handbrake Gaiter - round-hole type - for the transmission handbrake (parking brake) lever assembly. This rubber gaiter fits over the base of the L...

Facia Louvre Vent Housing for air-conditioned models, mounted in the facia as part of the cabin air distribution system. It carries the directiona...

Edge Clip - push-on edge clip that grips the flange of an interior trim panel, retaining both the panel and the wiring harness routed along its edg...

Seat Back Foam is the moulded foam pad that forms the front seat backrest. It belongs to the seat and trim assembly. The foam fits between the sea...

Seat Raising Kit is a pair of extended seat rails for one front seat, fitting in place of the standard seat runners within the seat mounting assemb...

screw M5 x 12

Heater Control Finger Grip The finger grip fitted to a heater control slider on the heater (HVAC) control panel, operated in the up/down plane. It...

Interior Door Handle for the left-hand side. Part of the door latch and release mechanism. Mounted on the inner door, the handle operates the latc...

Fusebox Housing Bolt is the threaded fastener that secures the fusebox housing within the dashboard. It retains the fuse box mounting in the parce...

Accelerator Pedal Lever Pad is the moulded rubber pad that fits over the accelerator pedal lever. It provides the contact face between the driver's...

The Interior Door Card Snap Sac Trim Clips are designed to securely fasten your vehicle's door card and trim pieces. Fitment: all models

Hex-head bolt, 1/4" UNF thread, 7/8" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socket...

Seat Base Foam Cushion forms the lower outer section of the seat base assembly within the interior seating system. It provides the primary support...

Loadspace Mat Retainer for the rear door aperture at the tailboard. The retainer is a profiled strip that clamps the rear door weatherseal and the...

Accelerator Pedal Return Spring for the cable-operated throttle linkage. The spring returns the accelerator pedal to its rest position when foot p...

Seat Belt Buckle - Right-Hand - the latching receptacle of the seat belt restraint, into which the belt tongue (latch plate) engages and locks to h...

Front seat belt LH

Screw M6 x 20 pan-head screw. It can be used in place of LR083229 (RYG500650 / DYP500210 / EYG50080) but is not identical: this screw has no capti...

Bolt, a hexagon-head fastener with a 5/16" UNF thread, 7/8" long. This imperial fastener is of the UNF (Unified National Fine) thread series and i...

Fir Tree Clip - a push-fit fastener that secures the door casing (interior door trim panel) to the door. The ribbed, tapered fir-tree stem pushes ...

Heater Control Finger Grip The finger grip fitted to the hot/cold (temperature) control on the heater control panel. It clips onto the control lev...

Steering Wheel Boss in the steering column assembly, providing the mounting interface between the column shaft and the steering wheel. The 48-spli...

Seat Back for the outer front seat, in the deluxe pattern and finished in black. This is the upholstered backrest (squab) the occupant leans agains...

High/Low Lever Gaiter - the flexible boot that seals the transfer box high/low range selector lever where it passes through the centre console. Fi...

Screw – a No. 6 × 1/2 in self-tapping screw used to secure interior trim and panel fixings, such as the instrument binnacle, fascia mouldings and a...

Window switch

Instrument Panel Finisher is the moulded trim panel that frames the instrument binnacle on the dashboard. It fits over the facia around the instru...

Fir Tree Fastener push-in fixing in grey, used to retain headlining, roof trim and similar interior and exterior trim panels. The tapered fir-tree...

Self-Tapping Screw – No. 8 × 5/8 in is a general-purpose fastener for securing body, trim and panel fixings. Being self-tapping, it forms its own ...

Hex-head bolt, 5/16" UNF thread, 3/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socke...

Carpet Drive Clip is an interior trim fastener used to retain the floor carpets against the body. The drive-clip design presses into a mounting ho...

Gaiter Retainer - secures the rubber gaiter around the high-low (transfer) lever on the LT76 gearbox, which carries an integral transfer box. The ...

Interior Door Handle for the right-hand side. Part of the door latch and release mechanism. Mounted on the inner door, the handle operates the lat...

Fir Tree Fastener push-in fixing used to retain body trim and exterior panels against the bodywork. The tapered fir-tree shank pushes into a pre-d...

Bolt 1/4" UNF x 2" is a hex-head set bolt with a 1/4-inch Unified National Fine (UNF) thread at 28 threads per inch and a 2-inch shank length. It ...

Door Card Fixing Kit for the interior door trim assembly of the Defender, in black. This kit provides the black-coloured rivets and fasteners requ...

Cubby Box Cup Holder for the centre console cubby box. The holder mounts to the sloping front face of the cubby box, providing a fixed location fo...

Hex-head screw, 5/16" UNF thread, 1-1/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and so...

Gear Lever Knob fits to the top of the manual gear lever within the gearchange assembly, providing the hand grip and carrying the gearshift pattern...

Gear Knob - LT95 is the hand grip fitted to the main gear lever of the LT95 4-speed gearbox. It threads onto the top of the gear lever and provide...

Coin Tray for the vehicle interior, providing a small open storage recess for coins, keys and other small items. The tray locates in the dashboard...

Fir Tree Clip push-in fastener used to secure interior door casings and trim panels to the body shell. The barbed fir-tree profile is pushed into ...

Decal

Steering Column Shroud (Lower) is the lower half of the two-part trim cover that encloses the steering column beneath the dashboard. It mates with...

Instrument Cowl is the binnacle that surrounds and shrouds the instrument cluster in the upper dashboard. Part of the fascia and instrument pack a...