Land Rover Interior Parts

Cigar Lighter - the panel-mounted lighter and 12V accessory socket in the instrument panel electrical system. The assembly comprises a socket and ...

Floor Mat Set is a set of tailored rubber floor mats that protect the cabin footwells from mud, water and everyday wear. The moulded rubber constr...

Fir Tree Fastener is a push-fit trim clip that retains roof insulation against the vehicle body. Its ribbed fir-tree shank pushes into a pre-forme...

Screw - a self-tapping pan-head fastener used in interior trim assembly. It cuts its own thread into the panel or moulded mounting boss to secure ...

Air Duct Seal - seals the heater air duct against the parcel tray within the HVAC air distribution. For vehicles without air conditioning.

Self-Tapping Screw – No. 6 × 3/4 in used to secure interior trim and panel fixings, such as the dash panel and upper fascia mouldings. Being self-...

Heater Duct, left-hand side, within the heater air distribution system. Routes air from the heater assembly to the floor-level outlet beneath the ...

Nut - 10/32" UNF A nut with a #10-32 UNF (Unified National Fine) internal thread, run onto a matching UNF bolt or stud to clamp the joint.

Double DIN Console - one-piece centre console fascia in black, providing the mounting aperture for a double DIN head unit in the Td5 dashboard. It...

Nut - M8 plain low-profile nut, sold individually. A standard metric M8 nut in the low-profile (thin) form. Used across gearbox, suspension, axle,...

Hex Head Bolt - 1/4" UNF thread, 5/8" long, with a hexagonal head. A general-purpose imperial fastener with a Unified Fine (UNF) thread form, driv...

Cable Gaiter - Door Wiring is a protective sleeve and grommet fitted at the door aperture of the Defender body, routing the door wiring harness saf...

Pedal Pad is the moulded rubber cover that fits over a foot pedal within the pedal box assembly, providing a non-slip contact surface for the drive...

Early Seat Diaphragm Door Only - Discovery 1 4

Window Regulator Escutcheon - Front Door

Pedal Pad - Clutch & Brake - moulded rubber pad that fits over the clutch and brake pedal arms in the pedal box. Provides the wear-resistant, ...

Seat Back Foam is the moulded cushioning for the outer front seat back. It forms the padded profile that sits over the seat back frame, beneath the...

Floor Mat is a moulded rubber footwell mat shaped to fit the right-hand floor over the gearbox tunnel. The foam backing adds sound insulation unde...

Floor Mat is a moulded rubber footwell mat shaped to fit the left-hand floor over the gearbox tunnel. The foam backing adds sound insulation under...

Interior Mirror Plate is the base/fixing plate that mounts the interior rear-view mirror to the body. It is a three-hole mounting plate that faste...

Alloy Gear & Transfer Box Knobs Machined alloy replacement knobs for the main gear lever and the transfer box lever, supplied as a matching pai...

Instrument Panel Dash Mounting for the instrument binnacle assembly. This structural mounting bracket secures the instrument panel within the dash...

Facia Panel Assembly - LHD is the end closing trim for the upper dashboard fascia on left-hand drive Defender 90 and 110, finished in black. This ...

Gearbox Tunnel Cover in moulded rubber for the transmission tunnel. It fits over the tunnel around the gear and transfer levers, giving a finished ...

Gear Lever Gaiter - black gaiter supplied with its housing, fitting over the main gear lever where it passes through the centre console. It seals ...

Seat Belt is the front right-hand inertia-reel seat belt assembly. It comprises the retractor, webbing and buckle tongue for the front right-hand ...

Nylon Stud, a trim retaining fastener used to hold interior trim panels and carpet in position. The stud pushes into a pilot hole in the body pane...

Leather hasp civilian

Carpet Drive Fastener is a trim fastener used within the interior floor carpet assembly to secure the carpet to the floor. The fastener is driven ...

Interior Trim Fastener in Bahama Beige, for securing rear interior trim panels in seven-seat Discovery 1 variants. This plastic push-in fastener c...

Front Floorplate - Left-Hand Side for the cab floor structure of Series II, IIA, and III Land Rovers. This pressed steel panel forms the left-hand...

Interior Trim Retainer Clip - a moulded fastener used to secure interior trim to the vehicle body. The clip retains door casings, pillar trims and...

Seat Mounting Plates for the seat installation assembly, supplied as a pair. These plates provide the fixed interface between the seat base frame ...

USB Charging Socket - a dashboard-mounted charging socket that fits a standard factory switch aperture, giving a flush, integrated appearance in pl...

Edge Clip - push-on edge clip that grips the flange of an interior trim panel, retaining both the panel and the wiring harness routed along its edg...

Toebox Trim Fastener - the fixing that secures the footrest and toebox trim panel in the footwell. It retains the lower trim at the A-post and toe...

Aluminium Pop Rivet, a blind rivet used as a general fixing for body panels, interior trim and seat-mounting brackets. It is set with a rivet gun: ...

Glovebox Lock Set secures the glovebox lid in the closed position and is released by key. It mounts in the glovebox within the facia, forming part ...

Switch Panel provides the mounting location for auxiliary switchgear in the dashboard and parcel-tray area of the fascia. Manufactured from alumin...

Seat Base - Techno Style The base cushion of a front seat, forming the seating surface that mounts to the seat frame and runners. Finished in the ...

Front Floorplate - Right-Hand Side for the cab floor structure of Series II, IIA, and III Land Rovers. This pressed steel panel forms the right-ha...

Seat Belt Bracket provides the upper shoulder belt anchorage point in the front seat restraint system. Fitted to the left-hand side, it secures th...

Flange Bolt is an M8 x 35 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Screw is an M4 x 8mm fastener used in the door mirror assembly, securing components of the interior and exterior mirrors at their mounting points. ...

Grommet / Blanking Plug - Dash Bulkhead for Land Rover Defender. This rubber plug seals an unused aperture in the dash bulkhead (such as a heater ...

Accelerator Pedal Pad - the moulded rubber cover that fits over the accelerator pedal. It provides a grippable, wear-resistant contact surface for...

Interior Lamp - courtesy lamp for the passenger compartment. Provides interior illumination as part of the interior lighting circuit, typically sw...

Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M5 thread with a 1...