Land Rover Series Parts

Rear Propshaft for the short-wheelbase chassis, forming part of the driveline between the transfer gearbox and the rear axle. The propshaft transm...

Manifold Stud - a mounting stud for the manifold. Threaded into the cylinder head, it locates the manifold and clamps it to the head face via its ...

Double-Grooved Ball Bearing for the manual gearbox and transfer box. It supports and locates a rotating shaft within the casing, carrying the radia...

Universal Joint is a cross-type (spider) joint fitted within the propshaft assembly, transmitting rotational drive between opposing yokes while acc...

Propshaft UJ Circlip - a retaining clip for the universal joint of the propeller shaft. It seats in the groove of the yoke ear and holds the beari...

Breather Set Screw secures the breather to the rocker cover within the engine crankcase ventilation arrangement. It retains the breather against t...

Front Bumper in galvanised steel, mounting across the front of the chassis frame. It bolts to the front chassis dumb-irons to provide front-end im...

Swivel Pin Housing Locking Plate mounts to the front axle swivel pin housing. It locks the swivel pin in position and provides the fixed stop that...

Cylinder Head Bolt - a clamping bolt securing the cylinder head to the engine block. It draws the head down onto the block to compress the head ga...

Drain Plug for the axle casing and fuel tank. This brass threaded plug seals the drain aperture at the bottom of the differential and axle casing,...

Rivet - a mechanical fastener used within the body and chassis assembly to join thin sheet metal and panel components. Nominal size 3/16" (4.8 mm)...

Ignition Condenser for the contact-breaker distributor, of the Lucas type, supplied with a long lead (17-7/8 in). Wired across the contact-breaker...

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the replaceable big-end shell bearings that fit between the connecting rods an...

Main Bearing Set for the Rover 3.5-litre V8 petrol engine. These are the replaceable shell bearings that carry the crankshaft in the cylinder block...

Window Channel

Seal Ring - a copper crush-type sealing washer. It fits beneath a threaded plug or at a metal-to-metal joint and deforms as it is tightened, takin...

Headlamp Bezel - stainless steel, 7". The trim ring that surrounds the 7" round headlamp, retaining the lamp unit in the front panel and finishing ...

Plain Nut - an M10 threaded fastener used at engine and chassis fixing points. Applications include retaining the shock absorber mountings to the ...

Oil Pump Shaft & Gear for the 3.5L V8 petrol engine, part of the lubrication system. The shaft and its drive gear transmit rotation from the ca...

Pinion Bearing (Outer) for the Salisbury axle differential. It is the outer of the pair of taper roller bearings that carry the drive pinion, seate...

Ignition Switch - Petrol - Steering Column is the electrical ignition and starter switch mounted in the steering column, forming part of the igniti...

Brake Pipe for the front braking hydraulic circuit. This is the flexible pipe that feeds the front wheel cylinders. It connects the chassis-mounte...

Split Pin - a 1.5mm x 12mm cotter pin used to lock a slotted (castle) nut or to retain a clevis pin. Passed through a drilled cross-hole in the sh...

Inlet Valve Stem Seal for the cylinder head valvetrain, fitted over the inlet valve stem at the top of the valve guide. The seal meters the oil pa...

Differential Guard for the axle differential, protecting the diff housing and cover from impact damage off-road. Clamps over the differential cent...

Tank Unit Screw is the slotted cheese-head securing screw for the fuel-tank sender unit. It clamps the fuel-level sender flange down onto the top ...

Inlet Valve Guide for the diesel cylinder head, part of the valve train. Pressed into the cylinder head, the guide locates the inlet valve stem an...

Glow Plug for the 2.25L diesel engine running a parallel (converted) glow plug system. Part of the cold-start pre-heating circuit. The glow plug h...

Indicator front/rear LED clear lens

Plain Washer - flat washer for use in general fastening assemblies throughout the vehicle. Distributes load and protects mating surfaces under bol...

Mirror Head - 195 mm x 145 mm. The rectangular exterior mirror head that fits the bar-type mirror arm, providing the driver's rearward view along t...

Decoke Gasket Set for the 3.5L V8 petrol engine with twin carburettors. The set supplies the gaskets needed when the cylinder heads are removed fo...

Rocker Shaft for the valvetrain of the Rover V8 petrol engine. The shaft mounts on the cylinder head and carries the rocker arms, transferring pus...

Hex-head bolt, 7/16" UNF thread, 1-1/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and soc...

Size/Diameter: 1/4" unf x 7/8"

Bolt - a hexagonal-head bolt with a 5/16" UNC (Unified Coarse) imperial thread and a 3/4" length. Used as an engine-assembly fixing, including cams...

Countersunk Screw - a machine screw with a flat, cone-shaped head that seats flush with the surface it fixes, leaving no proud edge. Metric M6 thr...

Pan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M6 thread with a 1...

Contact Set (breaker points) for the contact-breaker distributor, of the Ducellier type. The points are opened and closed by the distributor cam t...

Ignition Condenser for the contact-breaker distributor, of the Ducellier type. Wired across the contact-breaker points, the condenser absorbs the ...

Shock Absorber for the rear suspension, forming part of the rear axle damping assembly. This telescopic hydraulic damper is fitted between the cha...

Shock Absorber for the front axle, damping suspension movement by converting the energy of spring oscillation into heat as the axle moves relative ...

Brake Master Cylinder Repair Kit for the non-ABS brake master cylinder. The kit renews the internal seals when the master cylinder is overhauled, ...

Electric Fuel Pump mounted externally in the fuel supply system, drawing petrol from the tank and delivering it to the carburettor. This is an ext...

Hex Nut is a metric M5 hexagonal nut used as a general-purpose threaded fastener across multiple vehicle assemblies. It runs onto a matching M5 ma...

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Wheel Stud for use with Wolf-style rims in the wheel hub assembly. This 60mm long, 15mm diameter stud locates the wheel to the hub and secures it ...

Transfer Case Bottom Cover Gasket for the LT95 combined gearbox and transfer case. It seals the joint between the bottom cover and the transfer ca...