Land Rover Series Parts

Cylinder Head Bolt - a 7/16" UNC x 2.71" medium-type bolt for the Rover V8, part of the cylinder head fixings. This is the medium-length head bolt...

Engine Stud - a threaded manifold stud fitted to the exhaust system of the diesel engine. It threads into the cylinder head to provide a fixed anc...

Bolt

Mainshaft - Series 3

Layshaft Bearing for the early-type LT76 gearbox. It supports the layshaft (countershaft) within the gearbox, carrying the cluster gear that trans...

Fuel Pump Adaptor for mounting the external fuel pump on petrol engines. It provides the interface between the external fuel pump and its mounting...

Gearbox Gasket for the LT95 four-speed gearbox, sealing the power take-off (PTO) cover joint. Fits between the PTO cover and the gearbox main casi...

Exhaust Valve Guide is pressed into the cylinder head and supports the exhaust valve stem, keeping it accurately centred as the valve opens and clo...

Heater Control Pin

Oil Pump Relief Valve Spring - sets the pressure at which the oil pump's relief valve opens. It holds the relief valve plunger closed against the ...

Injector Bolt - the banjo bolt at the injector spill-return (leak-off) union. It clamps the leak-off pipe fitting to the top of the injector, its ...

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Crankshaft Thrust Washer controls crankshaft end-float - the axial movement of the crankshaft within the block - at the centre main bearing. The w...

Shackle Plate for the rear leaf spring shackle assembly. The shackle plate links the rear eye of the leaf spring to the chassis mounting, allowing ...

Washer - a plain flat washer used as a general-purpose fastening component across many assemblies on the vehicle. Fitted under a bolt head or nut,...

Locating Screw for the engine. A locating screw sets and holds the position of a component against its mounting during assembly. Applies to the 2....

Circlip for the throttle linkage on the carburettor V8 engine. It retains a pin or clevis within the throttle linkage, holding the linkage componen...

Fuel Cap closes and seals the fuel tank filler neck on petrol applications. It uses a two-lug bayonet fixing that locates and locks into the fille...

Door Seal - Front - Top is the weatherstrip that closes the joint between the top edge of the front door and the roof cant rail, forming part of th...

Bump Stop for the suspension, mounted at the limit of axle travel. This rubber stop caps upward suspension movement at full compression, providing...

Rope Hook

Headlamp Bezel is the outer retaining surround for the headlamp unit, mounting within the front lighting panel. It secures and finishes the lamp a...

Number Plate Lamp Plinth is the mounting base for the rear number plate lamp, fixing the lamp unit to the bodywork above the number plate. It loca...

Seat Belt Bracket for the front seat belt, lower mounting, right-hand side. This bracket bolts to the seat box and provides the lower anchorage po...

Circlip - Bonnet Prop Pin is the retaining circlip that secures the pin on the bonnet prop assembly. The circlip locates in a groove on the prop p...

Body Seal - a moulded rubber weather seal in the body & chassis assembly. It closes the gap between adjacent body panels to exclude water, dus...

Mounting Plate for the rear door spare wheel carrier assembly. This steel retainer plate secures the spare wheel against the tailgate-mounted spar...

Window Seal: rubber glazing seal for the window glass, sealing it against water and draughts.

Keep your Land Rovers interior clean and tidy with a loadspace mat. Ribbed rubber / 1,560 x 920 x 3mm Defender 110 - excluded 3 door commercial ...

Cab Mounting Stud

Front Outer Seat Cushion Base for the adjustable seat frame in Series II, IIA, and III 109" long-wheelbase vehicles. This is the outer seat base c...

Washer

Special Bolt with a coarse ACME-form thread, 1/4 in diameter and 5/8 in long. It is a body fixing used to secure inner-wing mudshields, floor plat...

Clevis Pin for the tailboard assembly at the rear of the body. It secures the drop-down tailboard's support cable or chain to its anchor bracket, ...

Flat Washer with a 3/8" bore, fitted under a bolt head or nut to spread the clamping load over a wider area and protect the mating surface.

Distance piece

Valve Collet for the valve gear of the 2.25L petrol and 2.0L diesel engines, used with single-groove valve stems. The split collets seat in the gr...

Joint Washer for the LT76 manual gearbox. Fitted between mating faces within the gearbox to form an oil-tight joint on assembly. Supplied as a sin...

Engine Stud for the Rover V8 petrol engine, measuring 5/16" x 2-1/8" with a UNC/UNF dual thread form. The coarse UNC end threads into the engine c...

Camshaft for the 2.25L 4-cylinder petrol engine valve train. Running in the cylinder block and driven from the crankshaft by the timing gear, the ...

Rocker Cover Washer used at the rocker (valve) cover fixing on the cylinder head. Fitted beneath the rocker cover retaining nut, the washer seals ...

Flywheel Bolt securing the flywheel to the rear flange of the crankshaft. Threaded 7/16 UNF with a 7/8 in shank length, the bolt clamps the flywhe...

Hose Clip for securing flexible hoses to pipes and stubs throughout the Land Rover. Tightening the clip compresses the hose onto the stub to form a...

Oil Relief Valve Sealing Washer seals the oil pressure relief valve within the engine oil pump assembly. It is fitted at the relief valve in the l...

Brake Servo Repair Kit for the Type 50 vacuum brake servo unit (227mm diameter). This overhaul kit contains the components necessary to rebuild th...

Ballast Resistor Resistor in the ignition primary circuit of the 3.5L V8 petrol engine. Wired in series with the ignition coil, it drops the suppl...

Barrel Lock and Key, Set of Two for the door locks, supplied as two keyed lock barrels each with a key. Each barrel is the cylinder the key turns ...

Seat Back and Headrest for the outer front seat, in the deluxe pattern and finished in black. This is the upholstered backrest (squab) the occupant...