for Discounts / VAT
for Discounts & Correct VAT
Parts for the full Land Rover Series family, produced from 1948 to 1985. This collection covers Series I, Series II, Series IIA, and Series III in both short wheelbase and long wheelbase configurations. Select your generation below to find correctly fitted components for your vehicle.
Wheel Nut A single-chamfer wheel nut that secures the road wheel to the hub studs. The chamfered seating face centres and clamps the wheel against...
View full detailsIgnition and Starter Switch - the electrical switch unit that mounts to the base of the steering column lock, in the ignition and starting circuit,...
View full detailsGearbox Cover Plate Gasket for the LT76 gearbox. This rubber gasket seals the cover plate to the gearbox casing, sealing the joint against oil lea...
View full detailsAccelerator Cable in the throttle control linkage, connecting the accelerator pedal to the carburettor throttle spindle. Transmits pedal movement ...
View full detailsInlet Valve for the cylinder head of the 2.25L 4-cylinder petrol engine, with a 44.5mm head diameter. It seats in the inlet port of the combustion...
View full detailsSeat Box End Panel - Right-Hand is a repair panel forming the outer end face of the seat box assembly. It replaces the corroded offside end panel ...
View full detailsDoor Pillar Repair Bracket for the front right-hand (offside) door pillar. A welded repair section that renews the front door pillar at the bulkhe...
View full detailsElectronic Distributor for the ignition system of the 4-cylinder petrol engine. It distributes high-tension voltage from the ignition coil to each...
View full detailsGearbox Tie Rod Buffer for the gearbox steady (tie rod) mounting. The tie rod restrains the gearbox against fore-and-aft movement under load. This...
View full detailsBattery Cover is the top fixing frame of the battery securing assembly. It clamps down over the top of the battery and bolts to the battery tray, h...
View full detailsDemister Tube
Exhaust Valve for the cylinder head valvetrain of the 2.25L and 2.5L naturally aspirated 4-cylinder diesel engines. The valve seals against its se...
View full detailsCon Rod Bearing Set - connecting rod big-end bearing shells for the 2.25L four-cylinder engine. The con rod bearings sit between the connecting ro...
View full detailsPan Head Screw - a machine screw with a low, rounded-top head and a flat bearing face, used as a general-purpose fixing. Metric M5 thread with a 1...
View full detailsDifferential Cover for the Salisbury rear axle. The cover bolts to the rear face of the axle casing, enclosing the crown wheel and differential and...
View full detailsDistributor Cap for the 2.6L 6-cylinder petrol ignition system on the Land Rover Series III. Fitted over the distributor body, the cap receives hi...
View full detailsMaster Cylinder Reservoir Cap seals the fluid reservoir on the brake or clutch master cylinder. It screws or presses onto the reservoir neck to re...
View full detailsMainshaft Peg is a locating peg fitted to the mainshaft of the LT67 gearbox. It positions and retains its associated component on the gearbox main...
View full detailsCon Rod Bearing Set - connecting rod big-end bearing shells for the 2.25L four-cylinder engine. The con rod bearings sit between the connecting ro...
View full detailsLock Washer for the carburettor butterfly spindle. This lock washer secures the retaining nut on the throttle butterfly spindle inside the carbure...
View full detailsHex nut
Plate - LH is the rear axle brake pipe shield (bracket) for the left-hand side. It mounts on the rear axle and shields the rigid brake pipe runnin...
View full detailsPlate - RH is the rear axle brake pipe shield (bracket) for the right-hand side. It mounts on the rear axle and shields the rigid brake pipe runni...
View full detailsTrack Rod Tube is the central bar of the steering track rod within the front steering linkage. Its threaded ends accept the track rod ends, joinin...
View full detailsSeat Base Cushion for the inner (centre) position of the 3-person front bench seat assembly. Constructed with a foam core upholstered in black vin...
View full detailsFlanged Bolt - an M6 x 25mm hexagon-head bolt with an integral flange formed beneath the head. The flange provides a wide bearing face that spread...
View full detailsDistance sleeve mainshaft
striker lock LH for "anti-burst" locks. (lift-up type)
Electronic Conversion Kit - electronic ignition conversion for the 4-cylinder petrol points distributor. Replaces the contact breaker points and c...
View full detailsGasket
Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...
View full detailsRocker Shaft - the hollow shaft that carries the rocker arms in the valvetrain, mounted across the cylinder head rocker pedestals. The rocker arms...
View full detailsMirror Head is a large replacement exterior door-mirror head measuring 265mm x 160mm, offering an increased field of view over the standard head. ...
View full detailsFootwell Repair Panel is a welded body repair panel for the right-hand (nearside) footwell, replacing the corroded or damaged footwell section ahea...
View full detailsSpare Wheel Carrier is a fixed rear-door-mounted bracket that supports and retains the spare wheel. It bolts directly to the rear door and locates...
View full detailsMaintain a warm and comfortable cabin in your Land Rover Series 3 with this high-quality heater matrix radiator. Designed as a direct replacement, ...
View full detailsMainshaft peg
Viscous Fan Assembly for the engine cooling system, mounting to the viscous coupling unit on the front of the engine. This 16", 7-blade white fan ...
View full detailsDifferential Bearing for the Salisbury axle. It is one of the pair of taper roller bearings that carry the differential carrier - the housing holdi...
View full detailsGasket kit carburettor Zenith Stromberg 175CD
Carburettor Float for the Zenith 361V carburettor, part of the Fuel System assembly on Series petrol engines. The float rides on the fuel surface ...
View full detailsWheel Hub Assembly - the complete axle hub, supplied with the wheel studs already fitted. It serves both front and rear hub positions. The hub mou...
View full detailsGearbox Side Cover Gasket for the LT95 4-speed V8 gearbox. This gasket seals the side cover to the gearbox casing, preventing oil leaks from the ge...
View full detailsthrust collar, bush for stub axle - RRclassic upto (VIN) HA610293, - 101" Forward Control.
Trunnion
Exhaust Valve Guide is pressed into the cylinder head and supports the exhaust valve stem, keeping it accurately centred as the valve opens and clo...
View full detailsU-Bolt - a spring-to-axle clamp in the front suspension. It wraps over the front axle and passes through a spring plate on the underside of the le...
View full detailsFuel Filler Breather Hose, part of the fuel filler and tank ventilation system. The hose vents air displaced from the fuel tank during refuelling,...
View full detailsParts for the full Land Rover Series family, produced from 1948 to 1985. This collection covers Series I, Series II, Series IIA, and Series III in both short wheelbase and long wheelbase configurations. Select your generation below to find correctly fitted components for your vehicle.
80, 86, 88 and 107-inch wheelbase variants. 1.6-litre and 2.0-litre petrol, 2.0-litre diesel from 1957.
Land Rover Series I parts (1948 to 1958) →88-inch SWB and 109-inch LWB. 2.25-litre petrol and diesel, 2.6-litre straight-six and 3.5-litre V8 in select variants.
Land Rover Series II, IIA and III parts (1958 to 1985) →The Land Rover Series family spans four distinct generations produced across 37 years. Series I ran from 1948 to 1958, Series II from 1958 to 1961, Series IIA from 1961 to 1971, and Series III from 1971 to 1985. Each generation used a body-on-frame ladder chassis with selectable four-wheel drive, a two-speed transfer gearbox, and a four-speed manual main gearbox. Wheelbase options were 88 inches (short wheelbase) and 109 inches (long wheelbase) from Series II onward. Series I used wheelbase options of 80, 86, 88, and 107 inches across its production run.
Parts compatibility is not uniform across the family. Some components, particularly engine internals for the 2.25-litre petrol and diesel units, carry across from Series IIA through Series III. Others, including body panels, wiring looms, and axle components, are generation or wheelbase specific. Selecting the correct child collection for your vehicle is the most reliable way to find the right parts.
Browse by generation:
If you are unsure which generation you have, use the vehicle commission number to identify your build date and sub-series before selecting parts.
The Land Rover Heritage Trust holds production records and commission number data for the Series family and is a reliable resource for vehicle identification.
This collection covers components across all major categories for the Series family. The heaviest demand comes from engine and gasket components, suspension and steering parts, body and chassis hardware, electrical and wiring items, and service and maintenance consumables.
Common restoration categories include engine rebuild components (gaskets, seals, bearings, timing parts), swivel housing and axle parts, wiring looms and electrical connectors, body panels and bulkhead sections, brake system components, and clutch and drivetrain parts.
For cross-category browsing by component type, the following category collections carry Series-compatible stock alongside parts for other Land Rover models:
Use the Model filter available on category collection pages to narrow results to Series I or Series 2 and 3 fitment where supported.
Buying GuideThe product grid offers three quality tiers: Genuine, OEM, and Aftermarket.
Genuine parts carry the original Land Rover part number and were manufactured by or for Land Rover. For Series vehicles, genuine Land Rover stock is limited for many components due to the age of the range. Where genuine parts are available, they are listed as Genuine.
OEM parts are manufactured to the same specification as the original part, often by the same supplier that produced the original component, but are sold outside the main brand distribution channel. For Series vehicles, OEM-specification parts are a reliable and widely used choice for mechanical rebuilds.
Aftermarket parts are independently manufactured to a compatible specification. Quality varies by product, and each listing on this site identifies the quality tier clearly. For consumable and body hardware categories on Series vehicles, quality aftermarket parts are the standard choice used by workshops across Europe.
Trade BuyersTrade customers running a workshop or managing multiple Series vehicles can access volume pricing through a Budget Parts trade account. Trade accounts include correct EU VAT invoicing, consolidated order options, and direct contact with the sourcing team for unlisted parts.
If a component is not currently visible in the catalogue, the sourcing team works directly with UK and EU suppliers to locate it. Contact the team with your commission number and part requirement.
Vehicle IdentificationSeries Land Rovers do not carry a modern 17-digit VIN. Each vehicle has a Commission Number on a bulkhead plate that encodes the generation, engine type, wheelbase and build date. Since the identification process and the records you cross-reference against differ between the four generations, the detailed Commission Number guidance lives on the two child collections, scoped to the vehicles each one covers.
For Series I (1948 to 1958), see the Series 1 collection. For Series II, IIA and III (1958 to 1985), see the Series 2 and 3 collection. Both pages cover where the plate sits on each generation, what the encoding tells you, and what to do if the plate is missing. If you have your Commission Number to hand and want fitment confirmed before ordering, contact Budget Parts directly.
Background ReadingFor deeper engineering and restoration context beyond the scope of this hub page, the following long-form guides cover each generation in detail. They are reference reading rather than navigation; the two child collections above are the route to parts.
A detailed reference covering Series I engine variants (1.6-litre and 2.0-litre petrol, 2.0-litre diesel), chassis design, wheelbase evolution, and the critical parts considerations for accurate restoration. Relevant for anyone sourcing components for a Series I vehicle or confirming specifications before ordering.
Series I engine and restoration guide →Covers the engineering and production history of Series II, IIA, and III models, including key differences between generations, engine fitment across sub-variants, and why certain parts are interchangeable while others are not. Useful background before selecting parts from the Series 2 and 3 collection.
Series II, IIA and III restoration guide →These are four successive generations of the same utility vehicle family, each sharing the core body-on-frame architecture but differing in engine, bodywork, and specification. Series I ran from 1948 to 1958 and used a 1.6-litre then 2.0-litre petrol engine, with a diesel option from 1957. Series II ran from 1958 to 1961 and introduced a revised body style. Series IIA ran from 1961 to 1971 and is the highest-volume production variant, available with 2.25-litre petrol and diesel engines and, in certain long wheelbase models, a 2.6-litre straight-six. Series III ran from 1971 to 1985 and brought minor updates including a revised instrument panel and an optional 3.5-litre V8 in select variants. Understanding which generation you have is the essential first step in selecting the correct parts.
Some parts are shared across Series IIA and Series III, particularly engine internals for the 2.25-litre petrol and diesel units, and certain axle and drivetrain components. However, body panels, wiring configurations, and some suspension components differ between generations. Parts shared across Series II and Series IIA are sometimes also different from early and late Series III specifications. The safest approach is to confirm fitment by generation and wheelbase before ordering, and to use the Series 2 and 3 parts collection for those specific generations.
Yes, significantly. Series I vehicles used different wheelbase dimensions (80, 86, 88, and 107 inches depending on year), different body construction details, and earlier engine specifications including the 1.6-litre petrol and the pre-2.25-litre 2.0-litre units. Many body, chassis, and mechanical components are unique to the Series I and do not carry across to Series II or later. The Series 1 parts collection is dedicated to this generation.
Start by identifying which generation your vehicle is. Series I (1948 to 1958) parts are unique to that generation in body, chassis and engine, and live in the Series 1 collection. Series II (1958 to 1961), Series IIA (1961 to 1971) and Series III (1971 to 1985) share considerable parts overlap and are grouped together in the Series 2 and 3 collection. If you are not sure which generation you have, the Commission Number on the bulkhead plate will tell you, and the child collections cover identification in more detail. Use the generation grid above to navigate to the correct collection for your vehicle.
Yes. The Series Land Rover aftermarket is one of the most active classic vehicle parts ecosystems in Europe. New replacement parts are produced for all four generations across the major categories: engine internals for the 2.25-litre petrol and diesel and the 2.0-litre Series I engines, body panels and chassis sections, electrical and wiring components, brake and suspension parts, and full restoration hardware. Genuine Land Rover stock is limited for parts of this age, but OEM-specification parts and quality aftermarket equivalents cover the majority of components in active demand. Specialist UK and EU manufacturers continue to remanufacture Series-specific items, and Budget Parts sources from this network for items not held in catalogue stock.
Start with three steps. First, identify your generation precisely (Series I, II, IIA or III) and your wheelbase, because every parts decision flows from those two facts. Second, work through a baseline service of consumables and wear items: brakes, fluids, filters, ignition components on petrol engines, glow plugs and fuel filters on diesels. Third, plan ahead for the higher-cost restoration items that often surface on Series vehicles after a few months of use, such as bulkhead repair sections, chassis outriggers, swivel housings and gearbox components. The two child collections (Series 1, and Series 2 and 3) hold the parts. The Series I and Series II/IIA/III restoration guides linked below cover the engineering background, common faults and parts priorities for each generation in more depth.