for Discounts / VAT
for Discounts & Correct VAT
Parts for the full Land Rover Series family, produced from 1948 to 1985. This collection covers Series I, Series II, Series IIA, and Series III in both short wheelbase and long wheelbase configurations. Select your generation below to find correctly fitted components for your vehicle.
Shackle Plate for the rear leaf spring shackle assembly, in the extended (long) form used on the heavier-duty chassis. It locates the outer eye of...
View full detailsShackle plate
Gasket
Clip
Seat Belt Bracket for the front seat belt, lower mounting, left-hand side. This bracket bolts to the seat box and provides the lower anchorage poi...
View full detailsRubber Washer - Window Catch for the sliding window catch assembly on Series II, IIA, and III Station Wagon body variants, produced up to 1984. Th...
View full detailsRear Sill Panel - Left Hand is a pressed steel body panel that forms the lower left-hand side of the rear body tub. The panel closes the gap betwe...
View full detailsFiller Strip for the door top. The strip fits along the top edge of the door, closing and finishing the joint at the door-top glass frame and seal...
View full detailsFront Floorplate - Left-Hand Side for the cab floor structure of Series II, IIA, and III Land Rovers. This pressed steel panel forms the left-hand...
View full detailsFront Floorplate - Right-Hand Side for the cab floor structure of Series II, IIA, and III Land Rovers. This pressed steel panel forms the right-ha...
View full detailsExhaust Packing Plate for the exhaust mounting strap assembly. It sits between the exhaust strap and its chassis bracket, packing the joint so the...
View full detailsEngine Mounting Bracket for the left-hand side of the engine, part of the engine mounting system. The bracket bolts to the left-hand side of the c...
View full detailsValve Cup for the valve gear of the 3-bearing 2.25L petrol and 2.0L diesel engines, used with single-groove valve stems. The cup seats on the top ...
View full detailsSump Gasket seals the joint between the oil sump and the cylinder block within the engine lubrication system, preventing oil leakage at the sump fl...
View full detailsTransfer Box Sealing Ring - Locking Pin A rubber O-ring that seals the locking pin where it enters the transfer box case. It seals the selector lo...
View full detailsStarter Brush Set A set of replacement carbon brushes for the starter motor, part of the engine starting circuit. The brushes bear on the commutat...
View full detailsRocker Shaft Bush in the cylinder head valvetrain. The bush is pressed into a rocker pedestal and provides the bearing surface that supports the r...
View full detailsExhaust Bracket for the exhaust system mounting. The bracket secures and locates the exhaust pipework against the underbody, supporting the system...
View full detailsBrake Shoe Anchor Plate for the rear drum brake assembly. The anchor plate provides the fixed abutment and locating point for the brake shoes. It ...
View full detailsGrommet seals and protects cables, harnesses and hoses where they pass through body and chassis panels. It is used at wiring harness pass-throughs...
View full detailsInterior Lamp - courtesy lamp for the passenger compartment. Provides interior illumination as part of the interior lighting circuit, typically sw...
View full detailsTappet kit
Shock Absorber Bush Set for the shock absorber mountings. This set provides the bushes that locate each shock absorber at its mounting eyes, insul...
View full detailsDynamo Brush Set for the Lucas C40 dynamo. The carbon brushes bear against the commutator to conduct current through the rotating armature windings...
View full detailsClutch Withdrawal Tube fitted in the clutch cross-shaft withdrawal mechanism on Series II, IIA, and III Land Rovers. This tube forms the connectin...
View full detailsCirclip - Gear Lever Spring Retention for the Series Land Rover gearbox gear lever assembly. This circlip retains the spring, retaining plate and ...
View full detailsTappet Slide for Land Rover 4-cylinder engines, covering the Series I, Series II, Series IIA, and Series III (2.0L Diesel and 2.25L Petrol and Dies...
View full detailsShock Absorber - Oil Filled - Front for the front suspension assembly on Series I, II, and IIA Land Rovers. This oil-filled hydraulic unit mounts ...
View full detailsHub Oil Seal seals the rear hub assembly, retaining lubricant within the hub and excluding dirt and moisture from the wheel bearings. It runs on t...
View full detailsBody Mounting Shim used to set the correct clearance and alignment between the body tub and the chassis mounting points. This thin flat shim is us...
View full detailsPlain Washer distributes the clamping load of a bolt or nut across the mounting surface and protects the surface as the fastener is tightened. Siz...
View full detailsSpring Washer for the fuel tank sender unit and fuel pick-up pipe fixings. Fitted beneath the retaining screws that secure the fuel gauge sender u...
View full detailsBolt - 5/16 inch BSF x 1 inch for the gearbox selector assembly. Used to secure the gear selector forks to their respective selector shafts within...
View full detailsFixed Towing Drop Plate bolts to the rear tow bar to carry the towball at the correct towing height. This is the extra-long version, giving a grea...
View full detailsRear Spring Hanger is a chassis mounting bracket in the rear leaf-spring suspension, forming the forward anchor point that carries the front eye of...
View full detailsDoor Check Arm Bracket is the pivot bracket in the door check assembly that anchors the check arm to the body at the rear door. The check arm runs...
View full detailsBulkhead Repair Panel with Vents - Right-Hand is a weld-in repair section for the upper corner of the bulkhead, incorporating the fresh-air vent su...
View full detailsSteering Relay Arm - Upper is the upper lever of the steering relay unit, the vertical relay mounted on the front chassis crossmember that transfer...
View full detailsStub Shaft with a 10-spline drive coupling, a component of the axle half-shaft assembly. The stub shaft sits within the axle and transmits drive t...
View full detailsTailgate Hook for the lower hinged tailboard, right-hand side. This pigtail (spiral) hook mounts on the body and retains the tailgate support stra...
View full detailsFront Exhaust Pipe forms the front section of the exhaust system, mounting to the exhaust manifold by a four-stud flange. It carries exhaust gas f...
View full detailsGear Lever for the main gearbox, right-hand drive configuration. The gear lever is the primary driver interface in the gearbox change mechanism, t...
View full detailsSteering Relay Shaft Bush - Split Half for the steering relay assembly on classic Land Rover models. This bush is supplied as one half of a split ...
View full detailsClutch Cover is the pressure plate assembly of the clutch, 9 inch (229 mm) diameter, coil-spring type with three release fingers. It bolts to the ...
View full detailsClutch Driven Plate for the LT95 four-speed gearbox, V8 petrol. The driven plate (friction disc) is splined to the gearbox input shaft and clamped...
View full detailsSidelight Bulb, rated 24V 10W, for the front sidelight (parking light) position. The bulb seats in the sidelight holder within the front lamp asse...
View full detailsChubby Cubby Box - a between-seats storage box and armrest that mounts on the centre panel of the seat box. It provides lockable interior storage ...
View full detailsChoke Cable for the DA2126 Weber carburettor conversion. This cable links the dashboard choke control to the carburettor's choke mechanism, provid...
View full detailsParts for the full Land Rover Series family, produced from 1948 to 1985. This collection covers Series I, Series II, Series IIA, and Series III in both short wheelbase and long wheelbase configurations. Select your generation below to find correctly fitted components for your vehicle.
80, 86, 88 and 107-inch wheelbase variants. 1.6-litre and 2.0-litre petrol, 2.0-litre diesel from 1957.
Land Rover Series I parts (1948 to 1958) →88-inch SWB and 109-inch LWB. 2.25-litre petrol and diesel, 2.6-litre straight-six and 3.5-litre V8 in select variants.
Land Rover Series II, IIA and III parts (1958 to 1985) →The Land Rover Series family spans four distinct generations produced across 37 years. Series I ran from 1948 to 1958, Series II from 1958 to 1961, Series IIA from 1961 to 1971, and Series III from 1971 to 1985. Each generation used a body-on-frame ladder chassis with selectable four-wheel drive, a two-speed transfer gearbox, and a four-speed manual main gearbox. Wheelbase options were 88 inches (short wheelbase) and 109 inches (long wheelbase) from Series II onward. Series I used wheelbase options of 80, 86, 88, and 107 inches across its production run.
Parts compatibility is not uniform across the family. Some components, particularly engine internals for the 2.25-litre petrol and diesel units, carry across from Series IIA through Series III. Others, including body panels, wiring looms, and axle components, are generation or wheelbase specific. Selecting the correct child collection for your vehicle is the most reliable way to find the right parts.
Browse by generation:
If you are unsure which generation you have, use the vehicle commission number to identify your build date and sub-series before selecting parts.
The Land Rover Heritage Trust holds production records and commission number data for the Series family and is a reliable resource for vehicle identification.
This collection covers components across all major categories for the Series family. The heaviest demand comes from engine and gasket components, suspension and steering parts, body and chassis hardware, electrical and wiring items, and service and maintenance consumables.
Common restoration categories include engine rebuild components (gaskets, seals, bearings, timing parts), swivel housing and axle parts, wiring looms and electrical connectors, body panels and bulkhead sections, brake system components, and clutch and drivetrain parts.
For cross-category browsing by component type, the following category collections carry Series-compatible stock alongside parts for other Land Rover models:
Use the Model filter available on category collection pages to narrow results to Series I or Series 2 and 3 fitment where supported.
Buying GuideThe product grid offers three quality tiers: Genuine, OEM, and Aftermarket.
Genuine parts carry the original Land Rover part number and were manufactured by or for Land Rover. For Series vehicles, genuine Land Rover stock is limited for many components due to the age of the range. Where genuine parts are available, they are listed as Genuine.
OEM parts are manufactured to the same specification as the original part, often by the same supplier that produced the original component, but are sold outside the main brand distribution channel. For Series vehicles, OEM-specification parts are a reliable and widely used choice for mechanical rebuilds.
Aftermarket parts are independently manufactured to a compatible specification. Quality varies by product, and each listing on this site identifies the quality tier clearly. For consumable and body hardware categories on Series vehicles, quality aftermarket parts are the standard choice used by workshops across Europe.
Trade BuyersTrade customers running a workshop or managing multiple Series vehicles can access volume pricing through a Budget Parts trade account. Trade accounts include correct EU VAT invoicing, consolidated order options, and direct contact with the sourcing team for unlisted parts.
If a component is not currently visible in the catalogue, the sourcing team works directly with UK and EU suppliers to locate it. Contact the team with your commission number and part requirement.
Vehicle IdentificationSeries Land Rovers do not carry a modern 17-digit VIN. Each vehicle has a Commission Number on a bulkhead plate that encodes the generation, engine type, wheelbase and build date. Since the identification process and the records you cross-reference against differ between the four generations, the detailed Commission Number guidance lives on the two child collections, scoped to the vehicles each one covers.
For Series I (1948 to 1958), see the Series 1 collection. For Series II, IIA and III (1958 to 1985), see the Series 2 and 3 collection. Both pages cover where the plate sits on each generation, what the encoding tells you, and what to do if the plate is missing. If you have your Commission Number to hand and want fitment confirmed before ordering, contact Budget Parts directly.
Background ReadingFor deeper engineering and restoration context beyond the scope of this hub page, the following long-form guides cover each generation in detail. They are reference reading rather than navigation; the two child collections above are the route to parts.
A detailed reference covering Series I engine variants (1.6-litre and 2.0-litre petrol, 2.0-litre diesel), chassis design, wheelbase evolution, and the critical parts considerations for accurate restoration. Relevant for anyone sourcing components for a Series I vehicle or confirming specifications before ordering.
Series I engine and restoration guide →Covers the engineering and production history of Series II, IIA, and III models, including key differences between generations, engine fitment across sub-variants, and why certain parts are interchangeable while others are not. Useful background before selecting parts from the Series 2 and 3 collection.
Series II, IIA and III restoration guide →These are four successive generations of the same utility vehicle family, each sharing the core body-on-frame architecture but differing in engine, bodywork, and specification. Series I ran from 1948 to 1958 and used a 1.6-litre then 2.0-litre petrol engine, with a diesel option from 1957. Series II ran from 1958 to 1961 and introduced a revised body style. Series IIA ran from 1961 to 1971 and is the highest-volume production variant, available with 2.25-litre petrol and diesel engines and, in certain long wheelbase models, a 2.6-litre straight-six. Series III ran from 1971 to 1985 and brought minor updates including a revised instrument panel and an optional 3.5-litre V8 in select variants. Understanding which generation you have is the essential first step in selecting the correct parts.
Some parts are shared across Series IIA and Series III, particularly engine internals for the 2.25-litre petrol and diesel units, and certain axle and drivetrain components. However, body panels, wiring configurations, and some suspension components differ between generations. Parts shared across Series II and Series IIA are sometimes also different from early and late Series III specifications. The safest approach is to confirm fitment by generation and wheelbase before ordering, and to use the Series 2 and 3 parts collection for those specific generations.
Yes, significantly. Series I vehicles used different wheelbase dimensions (80, 86, 88, and 107 inches depending on year), different body construction details, and earlier engine specifications including the 1.6-litre petrol and the pre-2.25-litre 2.0-litre units. Many body, chassis, and mechanical components are unique to the Series I and do not carry across to Series II or later. The Series 1 parts collection is dedicated to this generation.
Start by identifying which generation your vehicle is. Series I (1948 to 1958) parts are unique to that generation in body, chassis and engine, and live in the Series 1 collection. Series II (1958 to 1961), Series IIA (1961 to 1971) and Series III (1971 to 1985) share considerable parts overlap and are grouped together in the Series 2 and 3 collection. If you are not sure which generation you have, the Commission Number on the bulkhead plate will tell you, and the child collections cover identification in more detail. Use the generation grid above to navigate to the correct collection for your vehicle.
Yes. The Series Land Rover aftermarket is one of the most active classic vehicle parts ecosystems in Europe. New replacement parts are produced for all four generations across the major categories: engine internals for the 2.25-litre petrol and diesel and the 2.0-litre Series I engines, body panels and chassis sections, electrical and wiring components, brake and suspension parts, and full restoration hardware. Genuine Land Rover stock is limited for parts of this age, but OEM-specification parts and quality aftermarket equivalents cover the majority of components in active demand. Specialist UK and EU manufacturers continue to remanufacture Series-specific items, and Budget Parts sources from this network for items not held in catalogue stock.
Start with three steps. First, identify your generation precisely (Series I, II, IIA or III) and your wheelbase, because every parts decision flows from those two facts. Second, work through a baseline service of consumables and wear items: brakes, fluids, filters, ignition components on petrol engines, glow plugs and fuel filters on diesels. Third, plan ahead for the higher-cost restoration items that often surface on Series vehicles after a few months of use, such as bulkhead repair sections, chassis outriggers, swivel housings and gearbox components. The two child collections (Series 1, and Series 2 and 3) hold the parts. The Series I and Series II/IIA/III restoration guides linked below cover the engineering background, common faults and parts priorities for each generation in more depth.