for Discounts / VAT
for Discounts & Correct VAT
Parts for the full Land Rover Series family, produced from 1948 to 1985. This collection covers Series I, Series II, Series IIA, and Series III in both short wheelbase and long wheelbase configurations. Select your generation below to find correctly fitted components for your vehicle.
Nut A 4BA hex nut used as a threaded fastener. Applied on the door lock linkage and rear bumper mountings.
Steering Column Cover is the upper shroud enclosing the steering column. Fits together with the lower shroud 347558 to conceal the column and swit...
View full detailsSill Panel is the lower body closing panel that runs along the base of the door aperture, fitted to the right-hand side of the vehicle. Manufactur...
View full detailsFloor Mat Retainer secures the intermediate second-row rubber floor mat. Holds the mat in position against movement underfoot.
Round Head Rivet - 3/16in x 7/16in Steel
Front Outer Wing Panel - Aluminium - Left Hand Side for Series Land Rovers. This aluminium outer wing panel replaces the front left wing skin on S...
View full detailsRear Quarter Window Glass in clear (untinted) glass for the rear body side. It fits the quarter window aperture in the rear body, located alongsid...
View full detailsIgnition Starter Switch with Keys is the key-operated switch in the starting and ignition circuit. It controls the ignition and starter motor feed...
View full detailsStarter Solenoid Solenoid for the Lucas 3M100 starter motor on the 3.5L V8 petrol engine. Mounted on the starter motor body, it engages the starte...
View full detailsDog Guard for the Station Wagon, forming a full-height barrier between the rear load area and the passenger cabin to restrain animals or loose carg...
View full detailsStarter Solenoid - the solenoid for the Lucas M113 starter motor, part of the engine starting system. Mounted on the starter motor body, the solen...
View full detailsExhaust Valve for the cylinder head valvetrain of the 3.5 V8 petrol engine. The exhaust valve opens to release burnt gases into the exhaust port a...
View full detailsInlet Valve for the cylinder head valvetrain of the 3.5 V8 carburettor petrol engine. The inlet valve seals the intake port against combustion pre...
View full detailsStarter Drive
Front Bumperette - a compact protection unit fitted at the front of the vehicle. It provides localised impact protection to the front end. Manufac...
View full detailsPiston Ring Set for the 2.25L 4-cylinder petrol engine, ground to +0.040" (1.0mm) oversize for use with rebored cylinder bores. The rings seal the...
View full detailsVoltage Regulator - 22A for the charging system on Land Rover Series II, IIA, and III models with 4-cylinder petrol engines. Fitted between the dy...
View full detailsCrown Wheel & Pinion is the final-drive gear set within the differential, transferring drive from the propshaft into the axle and turning it th...
View full detailsEngine Overhaul Kit - 2.25L Diesel
Main Bearing Set for the 2.25L 4-cylinder petrol and diesel engine, supplied in 0.010" undersize. The main bearings are the replaceable shell bear...
View full detailsStarter Drive for the Lucas starter motor fitted to the 2.25L 4-cylinder diesel engine. The starter drive carries the pinion that engages the flyw...
View full detailsMain Bearing Set +0.030" 2,25
Bumperette - Rear - LH - Black is the left-hand rear bumperette, a corner protection unit mounted at the rear of the chassis. It bolts to the rear...
View full detailsBumperette - Rear - RH for the rear bumper assembly. This right-hand rear bumperette bolts to the outer end of the rear bumper cross-member, provi...
View full detailsBody Corner Capping, right-hand, galvanised steel. The protective capping that covers the rear corner of the body where the side and rear panels me...
View full detailsFume Curtain – Khaki Canvas is a canvas curtain that hangs across the rear of a soft-top vehicle to reduce the volume of exhaust fumes drawn into t...
View full detailsWheel Arch Kit is a four-piece set of moulded ABS plastic wheel arches. The kit comprises four wheel arch sections covering the front and rear arc...
View full detailsRear Door Chequer Plate Cover - external protection panel for the rear Safari (Station Wagon) door. The chequer plate fits over the outer face of t...
View full detailsRear Sill Panel - Left-Hand is a lower-body repair panel for the rear sill section on the nearside (left-hand) of the body. It forms the outer clos...
View full detailsCrossmember Cover - a cover panel for the chassis crossmember, forming part of the chassis and body structure.
Thrust Washer - intermediate shaft thrust washer for the LT95 four-speed gearbox. It controls the end-float of the intermediate (lay) shaft, takin...
View full detailsThrust Washer sits on the reverse gear shaft within the four-speed gearbox. It acts as a spacer alongside the reverse idler thrust washer, control...
View full detailsReverse Gear Needle Roller Bearing supports the reverse gear within the four-speed gearbox. It locates on the reverse gear shaft and carries the r...
View full detailsReverse Idler Shaft for the LT95 four-speed gearbox. The shaft carries the reverse idler gear, which transfers drive between the layshaft and main...
View full detailsSliding Block forms part of the first-gear synchroniser assembly within the four-speed LT95 gearbox. It locates in the synchroniser hub and transm...
View full detailsScreen to Drain Channel Rear Bracket - Left Hand, part of the windscreen and cab body framework. This bracket secures the windscreen rail to the o...
View full detailsFuel Pipe is a fuel line for the 2.25 litre diesel engine, forming part of the fuel delivery system. It carries fuel between components of the fue...
View full detailsPiston for the 2.25L 4-cylinder diesel engine, machined to +0.040" oversize for a rebored cylinder block. The piston transfers combustion pressure...
View full detailsVacuum Advance Hose for the carburettor-fed 2.25L 4-cylinder petrol ignition system. This hose carries ported vacuum from the carburettor to the d...
View full detailsCylinder head petrol 2.25 leadfree
Joint Washer sealing the carburettor to the inlet manifold on the Stage 1 V8. Forms the gasket joint between the carburettor base and the manifold...
View full detailsWoodruff Key locating the camshaft sprocket on the Rover V8 engine. Fits the 3.5L, 3.9L and 4.2L Rover V8. Not used on the 4.0L or 4.6L engines.
Roller Fairlead - zinc coated - for steel cable winches. This four-roller fairlead mounts to the front of a winch bumper and guides the steel cabl...
View full detailsLimited-Slip Differential is a helical-gear (Detroit TrueTrac type) limited-slip differential centre for the rear axle, with a 10-spline output. T...
View full detailsExtended Bulkhead Upper Repair Panel Set restores the upper section of the bulkhead, the structural firewall panel that separates the engine bay fr...
View full detailsRestore your Series 3 Land Rover with this brand-new bulkhead, designed for universal fitment to both Left-Hand Drive (LHD) and Right-Hand Drive (R...
View full detailsLockable Cubby Box is a centre-console storage box that mounts on the transmission tunnel between the front seats, providing a secure enclosed comp...
View full detailsCapture the sleek design of the Range Rover Evoque with this premium 1:76 scale diecast model in elegant Baltic Blue. This detailed replica perfect...
View full detailsParts for the full Land Rover Series family, produced from 1948 to 1985. This collection covers Series I, Series II, Series IIA, and Series III in both short wheelbase and long wheelbase configurations. Select your generation below to find correctly fitted components for your vehicle.
80, 86, 88 and 107-inch wheelbase variants. 1.6-litre and 2.0-litre petrol, 2.0-litre diesel from 1957.
Land Rover Series I parts (1948 to 1958) →88-inch SWB and 109-inch LWB. 2.25-litre petrol and diesel, 2.6-litre straight-six and 3.5-litre V8 in select variants.
Land Rover Series II, IIA and III parts (1958 to 1985) →The Land Rover Series family spans four distinct generations produced across 37 years. Series I ran from 1948 to 1958, Series II from 1958 to 1961, Series IIA from 1961 to 1971, and Series III from 1971 to 1985. Each generation used a body-on-frame ladder chassis with selectable four-wheel drive, a two-speed transfer gearbox, and a four-speed manual main gearbox. Wheelbase options were 88 inches (short wheelbase) and 109 inches (long wheelbase) from Series II onward. Series I used wheelbase options of 80, 86, 88, and 107 inches across its production run.
Parts compatibility is not uniform across the family. Some components, particularly engine internals for the 2.25-litre petrol and diesel units, carry across from Series IIA through Series III. Others, including body panels, wiring looms, and axle components, are generation or wheelbase specific. Selecting the correct child collection for your vehicle is the most reliable way to find the right parts.
Browse by generation:
If you are unsure which generation you have, use the vehicle commission number to identify your build date and sub-series before selecting parts.
The Land Rover Heritage Trust holds production records and commission number data for the Series family and is a reliable resource for vehicle identification.
This collection covers components across all major categories for the Series family. The heaviest demand comes from engine and gasket components, suspension and steering parts, body and chassis hardware, electrical and wiring items, and service and maintenance consumables.
Common restoration categories include engine rebuild components (gaskets, seals, bearings, timing parts), swivel housing and axle parts, wiring looms and electrical connectors, body panels and bulkhead sections, brake system components, and clutch and drivetrain parts.
For cross-category browsing by component type, the following category collections carry Series-compatible stock alongside parts for other Land Rover models:
Use the Model filter available on category collection pages to narrow results to Series I or Series 2 and 3 fitment where supported.
Buying GuideThe product grid offers three quality tiers: Genuine, OEM, and Aftermarket.
Genuine parts carry the original Land Rover part number and were manufactured by or for Land Rover. For Series vehicles, genuine Land Rover stock is limited for many components due to the age of the range. Where genuine parts are available, they are listed as Genuine.
OEM parts are manufactured to the same specification as the original part, often by the same supplier that produced the original component, but are sold outside the main brand distribution channel. For Series vehicles, OEM-specification parts are a reliable and widely used choice for mechanical rebuilds.
Aftermarket parts are independently manufactured to a compatible specification. Quality varies by product, and each listing on this site identifies the quality tier clearly. For consumable and body hardware categories on Series vehicles, quality aftermarket parts are the standard choice used by workshops across Europe.
Trade BuyersTrade customers running a workshop or managing multiple Series vehicles can access volume pricing through a Budget Parts trade account. Trade accounts include correct EU VAT invoicing, consolidated order options, and direct contact with the sourcing team for unlisted parts.
If a component is not currently visible in the catalogue, the sourcing team works directly with UK and EU suppliers to locate it. Contact the team with your commission number and part requirement.
Vehicle IdentificationSeries Land Rovers do not carry a modern 17-digit VIN. Each vehicle has a Commission Number on a bulkhead plate that encodes the generation, engine type, wheelbase and build date. Since the identification process and the records you cross-reference against differ between the four generations, the detailed Commission Number guidance lives on the two child collections, scoped to the vehicles each one covers.
For Series I (1948 to 1958), see the Series 1 collection. For Series II, IIA and III (1958 to 1985), see the Series 2 and 3 collection. Both pages cover where the plate sits on each generation, what the encoding tells you, and what to do if the plate is missing. If you have your Commission Number to hand and want fitment confirmed before ordering, contact Budget Parts directly.
Background ReadingFor deeper engineering and restoration context beyond the scope of this hub page, the following long-form guides cover each generation in detail. They are reference reading rather than navigation; the two child collections above are the route to parts.
A detailed reference covering Series I engine variants (1.6-litre and 2.0-litre petrol, 2.0-litre diesel), chassis design, wheelbase evolution, and the critical parts considerations for accurate restoration. Relevant for anyone sourcing components for a Series I vehicle or confirming specifications before ordering.
Series I engine and restoration guide →Covers the engineering and production history of Series II, IIA, and III models, including key differences between generations, engine fitment across sub-variants, and why certain parts are interchangeable while others are not. Useful background before selecting parts from the Series 2 and 3 collection.
Series II, IIA and III restoration guide →These are four successive generations of the same utility vehicle family, each sharing the core body-on-frame architecture but differing in engine, bodywork, and specification. Series I ran from 1948 to 1958 and used a 1.6-litre then 2.0-litre petrol engine, with a diesel option from 1957. Series II ran from 1958 to 1961 and introduced a revised body style. Series IIA ran from 1961 to 1971 and is the highest-volume production variant, available with 2.25-litre petrol and diesel engines and, in certain long wheelbase models, a 2.6-litre straight-six. Series III ran from 1971 to 1985 and brought minor updates including a revised instrument panel and an optional 3.5-litre V8 in select variants. Understanding which generation you have is the essential first step in selecting the correct parts.
Some parts are shared across Series IIA and Series III, particularly engine internals for the 2.25-litre petrol and diesel units, and certain axle and drivetrain components. However, body panels, wiring configurations, and some suspension components differ between generations. Parts shared across Series II and Series IIA are sometimes also different from early and late Series III specifications. The safest approach is to confirm fitment by generation and wheelbase before ordering, and to use the Series 2 and 3 parts collection for those specific generations.
Yes, significantly. Series I vehicles used different wheelbase dimensions (80, 86, 88, and 107 inches depending on year), different body construction details, and earlier engine specifications including the 1.6-litre petrol and the pre-2.25-litre 2.0-litre units. Many body, chassis, and mechanical components are unique to the Series I and do not carry across to Series II or later. The Series 1 parts collection is dedicated to this generation.
Start by identifying which generation your vehicle is. Series I (1948 to 1958) parts are unique to that generation in body, chassis and engine, and live in the Series 1 collection. Series II (1958 to 1961), Series IIA (1961 to 1971) and Series III (1971 to 1985) share considerable parts overlap and are grouped together in the Series 2 and 3 collection. If you are not sure which generation you have, the Commission Number on the bulkhead plate will tell you, and the child collections cover identification in more detail. Use the generation grid above to navigate to the correct collection for your vehicle.
Yes. The Series Land Rover aftermarket is one of the most active classic vehicle parts ecosystems in Europe. New replacement parts are produced for all four generations across the major categories: engine internals for the 2.25-litre petrol and diesel and the 2.0-litre Series I engines, body panels and chassis sections, electrical and wiring components, brake and suspension parts, and full restoration hardware. Genuine Land Rover stock is limited for parts of this age, but OEM-specification parts and quality aftermarket equivalents cover the majority of components in active demand. Specialist UK and EU manufacturers continue to remanufacture Series-specific items, and Budget Parts sources from this network for items not held in catalogue stock.
Start with three steps. First, identify your generation precisely (Series I, II, IIA or III) and your wheelbase, because every parts decision flows from those two facts. Second, work through a baseline service of consumables and wear items: brakes, fluids, filters, ignition components on petrol engines, glow plugs and fuel filters on diesels. Third, plan ahead for the higher-cost restoration items that often surface on Series vehicles after a few months of use, such as bulkhead repair sections, chassis outriggers, swivel housings and gearbox components. The two child collections (Series 1, and Series 2 and 3) hold the parts. The Series I and Series II/IIA/III restoration guides linked below cover the engineering background, common faults and parts priorities for each generation in more depth.