for Discounts / VAT
for Discounts & Correct VAT
Land Rover wheel accessories cover the smaller fitting and finishing parts that go around the wheel rather than the wheel itself: centre caps and hub caps, wheel spacers, tyre pressure sensors, balancing beads, valve hardware and inner tubes. This page brings them together for Series, Defender, Discovery, Range Rover and Freelander owners, so you can find the part that completes a wheel without scrolling past full wheels and nuts. Complete wheel hub assemblies and bearings are drivetrain parts and sit in Land Rover Suspension Parts, not here. Some parts are universal, while centre caps, spacers and sensors are matched to the wheel or vehicle, so check the fit before ordering. Everything here is stocked across our Dutch warehouse network for EU dispatch.
Single-point spare wheel mounting bracket for carrying one flat-sided fuel or water can on the spare wheel, moving can storage off the roof and out...
View full detailsBonnet Spare Wheel Support Plate - a reinforced plate that forms the mounting base for a bonnet-mounted spare wheel. It fixes to the bonnet panel ...
View full detailsSpare Wheel Retention Plate - the plate that holds the spare wheel against the rear-door-mounted spare wheel carrier. It clamps over the wheel and...
View full detailsSpare Wheel Cover - protective cover for the externally mounted spare wheel on the rear door. Fits over the exposed face of the spare wheel and ty...
View full detailsSingle Arm Spare Wheel Carrier - chassis-mounted swing-away carrier for the rear-mounted spare wheel. The carrier bolts to the chassis rather than...
View full detailsHeavy duty rear door spare wheel carrier, part of the rear door spare wheel mounting assembly. It replaces the original door-mounted carrier and bo...
View full detailsEz Deflator
Spare Wheel Cover finished in matt black with silver detailing. Fits over the externally mounted spare wheel to shield the tyre and rim from ultra...
View full detailsSpare Wheel Cover in a gloss black and silver finish, for the tailgate-mounted spare wheel. Shields the spare tyre from sunlight, road dirt and st...
View full detailsSpare Wheel Cover is a rigid cover that fits over an externally mounted spare wheel. Moulded in hard plastic with a gloss black finish, it shields...
View full detailsWheel Adaptor Kit, supplied as a set of four. The adaptors mount to the existing hubs and re-centre the wheel, allowing alloy wheels of the same st...
View full detailsAutomatic Tyre Deflators for dropping tyre pressure to a set figure without watching a gauge. Each deflator screws onto the tyre valve and vents a...
View full detailsGoodyear Wrangler Remoulded
Spare Wheel Bracket is the mounting bracket for a side-mounted spare wheel. Forms part of the side spare wheel carrier, working with the anchor pl...
View full detailsSpare Wheel Carrier Clamp Plate secures a bonnet-mounted spare wheel to its carrier. The plate clamps against the wheel to hold it firmly on the c...
View full detailsSpare Wheel Carrier Cable - the replacement cable stay for the swing-away rear-mounted spare wheel carrier. The cable tethers the swing-away carri...
View full detailsCover - Spare Wheel
Cover Assembly
Spare Wheel Cover - a padded vinyl cover that fits over an externally mounted spare wheel to protect the wheel and tyre from weather and dirt. Size...
View full detailsEnhance your Land Rover Defender's off-road capability with the Terrafirma Swing Away Spare Wheel Carrier, designed for Defender 90 and 110 Station...
View full detailsSpare Wheel Cover, semi-rigid moulded construction, matt black. The cover fits over the rear-mounted spare wheel and holds its own shape rather th...
View full detailsSpare Wheel Cover fits over an externally mounted spare wheel to protect the tyre and wheel from weather, road dirt and UV exposure. This is the h...
View full detailsSpare Wheel Cover - a soft cover that fits over an externally mounted spare wheel to shield the tyre and rim from dirt, road grime, moisture and UV...
View full detailsSpare Wheel Carrier mounts to the rear door to carry the spare wheel externally. It bolts through the door and provides the stud plate onto which ...
View full detailsWheel Cover 205 x 16
Spare Wheel Cover - hard-shell cover for a rear-mounted external spare wheel. Sized for a 17-inch wheel, the rigid moulded shell shields the spare...
View full detailsTyre Repair Kit for external plug repair of punctures in tubeless tyres, intended for off-road and emergency use. A puncture can be repaired with ...
View full detailsTyre Repair Kit A kit for the roadside repair of punctures in tubeless tyres. Repairs are made by inserting rubber plugs into the tread puncture t...
View full detailsTyre Pressure Sensor (TPMS) for the direct tyre pressure monitoring system. Fitted at the wheel valve inside the tyre, it measures tyre pressure an...
View full detailsTyre Pressure Sensor - component of the tyre pressure monitoring system (TPMS). Monitors tyre inflation pressure and transmits the reading by radi...
View full detailsTyre Pressure Sensor - wheel-mounted sensor forming part of the Tyre Pressure Monitoring System (TPMS). The sensor is fitted at the valve position...
View full detailsSpare Wheel Cover for an externally mounted spare wheel, sized to fit 235/70 R16 and 255/55 R18 tyres. The cover fits over the spare wheel and tyr...
View full detailsWheel Spacers - Set of 4 - spacers that fit between the hub and wheel to increase track width, improving stance and clearing larger tyres or brake ...
View full detailsWheel Cap - LH for the Freelander 1 wheel arch assembly. This left-hand wheel capping is a trim component that covers and finishes the wheel arch ...
View full detailsFront Wheel Hub Assembly for the front suspension corner. The hub carries the road wheel and, through its integral bearing, lets the wheel rotate ...
View full detailsTyre Pressure Monitoring System is a universal Bluetooth system that reports live tyre pressure and temperature to a smartphone app. Four sensor ca...
View full detailsTyre Pressure Sensor - wheel-mounted pressure and temperature sensor for the Tyre Pressure Monitoring System (TPMS). Mounted at the valve position...
View full detailsWheel Centre Cap - hub cover for modular steel road wheels. It press-fits into the centre bore of the wheel, covering the hub flange and keeping d...
View full detailsWheel Cover for the road wheel. The cover fits over the wheel to give a finished appearance and shield the wheel face from road dirt and brake dus...
View full detailsWheel Cover set, fitted over the road wheels. The covers clip over the wheels to give a finished appearance and shield the wheel face from road di...
View full detailsTPMS Sensor Kit for the tyre pressure monitoring system. The sensor sits inside the wheel at the valve position, measuring the tyre's internal pres...
View full detailsTyre Pressure Monitoring Sensor (TPMS), TGIC type, operating at 433 MHz. Mounted at the wheel, the sensor measures tyre pressure and transmits the...
View full detailsWheel Centre Cap - Black - black centre cap for the Winrace alloy wheel, supplied individually. The cap closes the centre bore of the wheel, cover...
View full detailsTyre Pressure Sensor (TPMS) for the direct tyre pressure monitoring system. Fitted at the wheel valve inside the tyre, it measures tyre pressure an...
View full detailsTyre Pressure Sensor (TPMS) for the direct tyre pressure monitoring system. Fitted at the wheel valve inside the tyre, it measures tyre pressure an...
View full detailsWheel Centre Cap for the alloy road wheel. This cover fits to the hub centre of the alloy wheel, closing off the centre bore and completing the wh...
View full detailsTyre Balancing Beads
Tyre Balancing Beads
This collection holds the parts that sit alongside a wheel rather than the wheel and its fixings. That means centre caps and hub caps that cover the centre bore, wheel spacers that push the wheel outward for clearance or a wider track, tyre pressure monitoring sensors on models fitted with them, balancing beads and weights, valve caps and stems, and inner tubes for steel wheels. The wheels themselves, and the nuts and studs that hold them on, sit in their own sections, so this page stays focused on the finishing and fitting parts. It covers Land Rover and Range Rover from the Series and classic Defender through to the later Discovery and Range Rover ranges.
A few of these parts are broadly interchangeable. Balancing beads, valve caps and most valve hardware are not tied to a particular model. The rest are matched to the wheel or the vehicle. Centre caps are sized to the wheel's centre bore and to the badge style, so a cap for a steel wheel will not suit a later alloy. Wheel spacers are matched to the hub stud pattern and centre bore, and add a fixed amount of track each side. Tyre pressure sensors are matched to the model, year and radio frequency the vehicle expects. Inner tubes are sized to the wheel and tyre. When a part is size or model dependent, confirm it against your wheel or vehicle before ordering.
The quickest way to get the right accessory is to work from the wheel you already have. For a centre cap, measure the opening it pushes into, or quote the part number stamped on the old cap. For a spacer, you need the stud pattern and centre bore of your hub, plus the thickness you want. For a tyre pressure sensor, your model and build year decide the correct type, since fitment changed across generations and left and right hand drive markets. If you are replacing like for like, matching the new part to the old one is the safest check.
It is the group of parts that go around a wheel rather than the wheel itself or the nuts that hold it on. That includes centre caps and hub caps, wheel spacers, tyre pressure monitoring sensors, balancing beads and weights, valve caps and stems, and inner tubes. Complete wheels sit in road wheels and spares, and the fixings sit in wheel nuts and locks.
Centre caps are sized to the centre bore of the wheel and to the badge style, so they are not universal across the range. A cap made for a steel wheel will not suit a later alloy, and sizes changed across models. The safest approach is to measure the opening the cap pushes into, or to quote the part number on your existing cap, before ordering.
Wheel spacers are matched to your hub by stud pattern and centre bore, and they add a set amount of track on each side based on their thickness. Choose the spacer that matches your hub fitment and the clearance you need, and check that your wheel nuts or longer studs still give full thread engagement once fitted. Local road rules on track width and spacers vary, so confirm what is permitted where you drive.
Yes. Tyre pressure monitoring sensors are matched to the model, build year and the radio frequency the vehicle expects, which is typically 433 megahertz on European Land Rover and Range Rover models. A sensor from the wrong generation may not pair with the vehicle, so confirm the correct type against your model and year before ordering.
Balancing beads, valve caps and most valve hardware are not tied to a specific model, so they suit the range broadly. Centre caps, spacers, tyre pressure sensors and inner tubes are size or model dependent and should be matched to your wheel or vehicle.
Budget Parts. Land Rover and Range Rover wheel accessories, stocked in the Netherlands for EU dispatch.