Land Rover Wheel Bearings & Seals

Hub Cap closes the centre of the front hub drive flange, covering the driveshaft coupling bolts within the front axle hub assembly. This version c...

Speedo cable oil seal retainer plate

Oil Seal for the input shaft of the ZF automatic gearbox. The seal fits at the front of the gearbox, where the torque converter drives the input s...

Output Shaft Oil Seal seals the output shaft of the LT95 four-speed gearbox and integral transfer box, retaining gear oil where the shaft passes th...

Primary Pinion Bearing for the manual gearbox, supporting the primary pinion (gearbox input shaft). The primary pinion transmits drive from the cl...

Hub Outer Oil Seal for the front and rear wheel hub assemblies. Located at the outer end of the hub, it retains the wheel-bearing grease within the...

Differential Pinion Bearing Spacer used in the axle differential assembly across a broad range of Land Rover models from 1965 onwards. This spacer...

Oil Seal for the front cover of the LT85 five-speed manual gearbox. It seals the front cover where the primary (input) shaft enters the gearbox, re...

Snap Ring retaining the rubber dust boot on a track rod end within the steering linkage. A spring-steel ring that seats in the outer groove of the...

Differential Pinion Oil Seal with a double sealing lip, for the front and rear differentials. It is press-fitted into the differential housing aro...

Crankshaft Oil Seal - Rear - Heavy Duty for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal hou...

Swivel Pin Housing Oil Seal for the front axle swivel and stub axle assembly. This is the outer seal, fitted at the interface between the stub axle...

Camshaft Oil Seal seals the camshaft on the 2.5L 4-cylinder diesel engines, including the 200TDi. Fitted at the front of the engine where the cams...

Crankshaft Oil Seal seals the front timing cover where the crankshaft nose passes through it. Fitted to the 2.5L 300 TDi diesel engine, the seal r...

Power steering seal kit

Track Rod End Boot Ring - spring retaining ring for the track rod end of the steering linkage. It clamps the rubber dust boot onto the track rod en...

Hub Oil Seal for the front axle, sealing the front hub and drive shaft assembly to retain hub lubricant and exclude water, dirt and grit from the w...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Transfer Box Output Shaft Mud Shield fitted at the output shaft oil seal of the LT230 transfer box. The shield sits over the output shaft ahead of...

Pinion Bearing - 35 × 68.5mm, a tapered roller bearing installed on the Constant Mesh Pinion shaft within the LT77, R380, and LT95 manual gearboxes...

Crankshaft Oil Seal - Rear for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal housing at the f...

Oil Seal Collar for the R380 manual gearbox. The collar fits over the output shaft and provides the hardened running surface against which the gea...

Front Wheel Bearing Kit for the front hub on vehicles without ABS, fitted with Timken taper roller bearings. The bearings carry the front wheel hu...

Snap Ring

Crankshaft Oil Seal - Rear for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal housing at the f...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Oil Seal - Cylinder Head Oil Feed - Front, part of the Engine Lubrication Circuit on the 2.5L VM Turbo Diesel. This seal is installed at the front...

Gearbox Mainshaft Oil Seal, fitted where the mainshaft passes through the gearbox casing on the 5-speed manual transmission. It runs against the r...

Needle Roller Bearing for the R380 manual gearbox. It carries the reverse idler on the layshaft, allowing the gear to rotate with minimal friction ...

Hub Bearing Kit - Front - Non-ABS

Oil Seal

Needle Roller Bearing

PAS pump seal kit

Seal Kit - 11" Travel Shock

Hub Bearing Kit - Front - With ABS

Wheel Bearing Kit - Rear Axle - Non-ABS

Seal - Oil Pump

Oil Seal for the LT230 transfer box input shaft. Part of the transfer box gear train. The seal fits around the rotating input shaft where it enter...

Rear Wheel Bearing Kit containing the parts needed to overhaul one rear hub bearing assembly on non-ABS vehicles. The taper roller bearings carry t...

Front Wheel Bearing Kit containing the parts needed to overhaul one front hub bearing assembly on non-ABS vehicles. The taper roller bearings carry...

Rear Wheel Bearing Kit containing the parts needed to overhaul one rear hub bearing assembly on ABS-equipped vehicles. The taper roller bearings ca...

Gearchange Lever Oil Seal seals the gearchange lever where it enters the manual gearbox housing. It retains transmission oil around the selector l...

Oil Seal for the transfer section of the LT95 combined gearbox and transfer unit, sealing the rear mainshaft. It runs on the rear mainshaft where ...

Oil Seal for the LT95 four-speed gearbox, retaining lubricant within the gearbox and transfer casing. It runs against a rotating shaft to keep gea...

Front Wheel Bearing Kit containing the parts needed to overhaul one front hub bearing assembly on ABS-equipped vehicles. The taper roller bearings ...

Rear Wheel Bearing Kit containing the parts needed to overhaul one rear hub bearing assembly on ABS-equipped vehicles. The taper roller bearings ca...

Rear Wheel Bearing Kit containing the parts needed to overhaul one rear hub bearing assembly on non-ABS vehicles. The taper roller bearings carry t...

Seal Kit - Bump Stop