Land Rover Defender New Parts

Drive Belt Idler Pulley - a non-driven guide pulley in the accessory drive belt system of the 3.0L AJ20P6 six-cylinder petrol engine. The idler gu...

Moulding - Front Wheel Arch

Breather Tube forming part of the crankcase ventilation circuit on the 5.0L V8 petrol engine (AJ133). It carries crankcase blow-by gases from the ...

Retaining Clip is a fastening clip used in the radiator grille and front bumper assembly. It secures the grille and front bumper trim components t...

Clip - retaining clip for the radiator grille and front bumper assembly. It secures the grille and bumper components to their mountings.

Overflow Container Cap for the cooling system expansion (overflow) reservoir. The cap seals the coolant expansion tank and maintains system pressu...

Plus Foam Air Filter Eqv LR129322

Brake Pad Set - Rear - friction pad axle set for the rear disc brake assembly. The pads locate in the rear caliper carriers and clamp against the ...

Final Drive Lubricant - a fully synthetic 75W-90 gear oil meeting API GL5, supplied in a 4 litre pack. Specified for the front and rear final driv...

Front Brake Disc, 363 mm diameter - front foundation brake assembly. The disc locates on the front hub and provides the friction surface for the f...

Rear Door Organiser - MOLLE-pattern storage panel mounted to the inside face of the rear door. The webbing grid accepts MOLLE-compatible pouches a...

Brake Caliper Guide Pin Dust Cover for the front and rear brake calipers. The boot fits over the caliper guide pin and seals against the carrier b...

Cylinder Head Gasket sealing the cylinder head to the engine block. Fitted to the 2.0L four-cylinder AJ200 (Ingenium) petrol engine, including PHE...

Brake Caliper Bleed Screw for the front and rear brake calipers. The bleed screw threads into the bleed port on the caliper body and is opened to ...

Camshaft Position Sensor mounted in the timing gear cover, reading the toothed target on the camshaft drive to give the engine control module a dir...

Spark Plug Aperture Gasket seals the spark plug aperture in the cylinder head cover on the left hand cylinder bank. It closes the joint between th...

Camshaft Position Sensor mounted in the timing gear cover, reading the toothed target on the camshaft drive to give the engine control module a dir...

Thermostat Housing for the 5.0-litre AJ133 V8 petrol engine, part of the engine cooling circuit. The housing seats the coolant thermostat and form...

Thermostat Housing for the 5.0-litre AJ133 V8 petrol engine, part of the engine cooling circuit. The housing seats the coolant thermostat and form...

Fuel Filler Restrictor for diesel vehicles, fitted inside the fuel filler neck as part of the fuel tank and filler assembly. It forms a physical b...

Chain - Timing

Brake Disc & Caliper Bolt - a fixing bolt for the brake disc and caliper assembly. It is used at both the front and rear brake disc and calipe...

O-Ring seals the variable valve timing (VVT) solenoid within the timing gear and sprocket assembly. It maintains an oil-tight joint between the VV...

Exhaust Gas Temperature Sensor for the lower sensing position at the diesel particulate filter, within the exhaust aftertreatment system. The sens...

Inlet Manifold Gasket - 5.0 V8 - RH seals the inlet manifold to the cylinder head on the right-hand bank of the 5.0 litre V8 petrol (AJ133) engine,...

Brake Disc & Caliper Bolt - a fixing bolt for the brake disc and caliper assembly. It is used at both the front and rear brake disc and calipe...

Gasket - Oil Filter to Block seals the joint between the oil filter housing and the cylinder block, within the Oil Cooler and Filter assembly. It ...

Spark Plug Aperture Gasket for the right-hand camshaft cover, sealing the spark plug well against oil ingress. The camshaft cover carries a tube f...

O-Ring for the oil pump inlet tube, part of the oil pump, sump and filter assembly. It seals the joint at the oil pump inlet (pick-up) tube, keepi...

Gasket - Oil Filter to Block seals the joint between the oil filter housing and the cylinder block, within the Oil Cooler and Filter assembly. It ...

Fuel Pressure Sensor for the high-pressure fuel injection circuit on petrol engines. It measures fuel rail pressure and temperature and reports to ...

Inlet Manifold Gasket - 5.0 V8 - RH seals the inlet manifold to the cylinder head on the right-hand bank of the 5.0 litre V8 petrol (AJ133) engine,...

Front Brake Pad Kit - friction pad set for the front disc brake assembly, for the 380 mm front disc and size 20 caliper configuration. The pads lo...

Exhaust Gas Temperature Sensor located at the turbocharger. It measures the exhaust gas temperature entering the turbine and aftertreatment stage a...

Blanking Plug used within the engine cooling system - thermostat housing, radiator and coolant expansion tank, and the cooling pipework. The plug ...

Expansion Tank Seal - sealing ring for the bleed valve fitted to the coolant expansion tank in the engine cooling system. Seals the bleed valve in...

Drive Fastener - black plastic drive-in retaining clip used to secure body mouldings, trim panels and interior finishers to their mounting panels. ...

Cam Cover Gasket for the right-hand cylinder head of the 5.0L AJ133 V8 petrol engine, part of the camshaft cover assembly. The gasket seals the jo...

Intercooler Pipe connecting the turbocharger outlet to the intercooler in the charge-air system of the 2.0L AJ200 (Ingenium) four-cylinder diesel e...

Inlet Valve - cylinder head inlet (induction) valve for the 5.0L V8 AJ133 supercharged petrol engine. The inlet valve admits the intake charge int...

Timing Tensioner Screw - M8 x 45mm is the fastener that secures the chain tensioner within the timing gear assembly of the 5.0 litre V8 petrol (AJ1...

Rear Brake Disc - a vented disc from the rear brake disc and caliper assembly. The disc is mounted on the rear hub behind the road wheel and rotat...

Primary Timing Chain Tensioner from the timing drive assembly at the front of the 2.0L four-cylinder AJ200 / AJ20P4 engine. The tensioner bears ag...