Land Rover Defender New Parts

Clip is a fastening used within the body moulding assembly, retaining exterior trim and moulding panels against the bodywork.

Gasket - Exhaust Manifold

O-Ring for the oil filter and cooler assembly. It seals a connection within the oil cooler and filter assembly, maintaining oil-tight integrity at...

Sealing Ring sealing a joint within the engine timing gear covers. This O-ring seals a connection at the timing cover assembly, maintaining oil-ti...

Bolt securing the fuel injector and high-pressure fuel pipe assembly on the engine fuel system. It clamps the injector and high-pressure pipe unio...

Oil Drain Plug for the engine oil pan (sump). Threaded into the base of the oil pan, it seals the oil drain point and is removed to drain the engi...

Fixing Screw, M6 x 65 mm. A threaded fastener used as a general fixing across a range of vehicle assemblies.

Magnetic Oil Drain Plug - M14 x 21 sump drain plug in the engine lubrication system. The plug seals the drain aperture in the oil sump and is remo...

Timing Chain Guide for the primary timing chain, fitted on the right-hand side of the timing drive. It locates and supports the chain along its ru...

Timing Chain Blade is the tensioner blade in the engine's timing chain drive. It provides the curved, low-friction face that the timing chain bears...

O-Ring seal for the automatic transmission oil cooler circuit (ZF 8-speed, 8HP). The O-ring seals a connection in the transmission fluid cooling c...

Water Pump Gasket for the coolant pump on 5.0L V8 (AJ133) and 3.0L supercharged V6 petrol engines. The gasket seals the joint between the water pu...

Anti-Roll Bar Link - connects the rear anti-roll (stabilizer) bar to the suspension on the left-hand side. This drop link transfers body-roll load...

Gasket - Throttle

Degas Hose for the engine cooling system's degassing circuit. The hose routes coolant and entrained air from the engine and radiator to the degas (...

Ignition Coil for V6 and V8 petrol engines, mounted directly on the spark plug in a coil-on-plug arrangement. The coil steps up the battery supply...

Idler Pulley for the secondary drive belt circuit on supercharged petrol engines. The idler is a freely-rotating, sealed-bearing pulley that guide...

Coolant Hose carries engine coolant through the cooling circuit, connecting the components that circulate coolant to and from the engine. Moulded ...

Body Moulding Retainer Clip, a lantern-type fastener for the vehicle's exterior trim. The clip secures exterior body mouldings - such as the rocke...

Oil Cooler Tube carries engine oil through the oil cooler circuit. The tube connects the engine oil system to the oil cooler, routing oil to be co...

O-ring for the variable valve timing (VVT) solenoid, part of the timing gear assembly at the front of the engine. The solenoid meters oil flow to ...

Vacuum Pump Seal - sealing ring between the engine-driven vacuum pump and its mounting face on the engine, forming part of the brake servo vacuum c...

O-Ring - Radiator Hose

Gasket - Oil Cooler seals the engine oil cooler to its mounting face, within the Oil Cooler and Filter assembly. It maintains the integrity of the...

Front Brake Caliper Attachment Kit - the caliper fitting hardware for the front disc brake assembly. The kit contains the brake pad clips and the ...

Brake Caliper Locating Pin Kit for the sliding brake caliper. The guide pins let the caliper float on its carrier bracket so both brake pads wear ...

Ignition Coil for the 2.0L four-cylinder petrol engine (AJ200 / AJ20P4, including PHEV). This is a coil-on-plug unit that mounts directly on the sp...

Hub Bearing

Brake Caliper Guide Pin Dust Cover for the front and rear brake calipers. The boot fits over the caliper guide pin and seals against the carrier b...

Brake Caliper Bleed Screw for the front and rear brake calipers. The bleed screw threads into the bleed port on the caliper body and is opened to ...

Camshaft Position Sensor mounted in the timing gear cover, reading the toothed target on the camshaft drive to give the engine control module a dir...

Drive Fastener - black plastic drive-in retaining clip used to secure body mouldings, trim panels and interior finishers to their mounting panels. ...

Steering Column Repair Gaiter is a replacement gaiter for the steering column. It seals the steering column and is supplied as a repair item to re...

Piston - 0.50 mm Oversize for the 2.0-litre Ingenium (AJ200D / 204DTD) diesel engine. An engine-rebuild piston machined 0.50 mm over the standard ...

Crankcase Breather Cover - part of the crankcase ventilation assembly on the 3.0L Ingenium AJ20P6 six-cylinder petrol engine. The cover closes the...

Hood Latch for the bonnet closing mechanism. The latch is body-mounted and engages the bonnet striker to hold the bonnet shut, releasing when the ...

Water Pump for the 3.0L supercharged V6 and 5.0L V8 petrol (AJ133) engines. The pump circulates coolant through the engine block, cylinder heads a...

Front Suspension Arm - lower rear arm of the front suspension assembly, right-hand side. It links the lower end of the front knuckle to the subfra...

Front Suspension Arm - lower rear arm of the front suspension assembly, left-hand side. It links the lower end of the front knuckle to the subfram...

Oil Cooler, part of the engine lubrication system. It draws heat out of the engine oil to hold oil temperature within its operating range under su...

Air Suspension Levelling Valve - front valve block in the four-corner electronic air suspension circuit. It sits between the compressor and reserv...