Land Rover Defender New Parts

Fixing Screw, M6 x 65 mm. A threaded fastener used as a general fixing across a range of vehicle assemblies.

Timing Chain Guide for the primary timing chain, fitted on the right-hand side of the timing drive. It locates and supports the chain along its ru...

Timing Chain Blade is the tensioner blade in the engine's timing chain drive. It provides the curved, low-friction face that the timing chain bears...

Water Pump Gasket for the coolant pump on 5.0L V8 (AJ133) and 3.0L supercharged V6 petrol engines. The gasket seals the joint between the water pu...

Anti-Roll Bar Link - connects the rear anti-roll (stabilizer) bar to the suspension on the left-hand side. This drop link transfers body-roll load...

Gasket - Throttle

Degas Hose for the engine cooling system's degassing circuit. The hose routes coolant and entrained air from the engine and radiator to the degas (...

Ignition Coil for V6 and V8 petrol engines, mounted directly on the spark plug in a coil-on-plug arrangement. The coil steps up the battery supply...

Idler Pulley for the secondary drive belt circuit on supercharged petrol engines. The idler is a freely-rotating, sealed-bearing pulley that guide...

Coolant Hose carries engine coolant through the cooling circuit, connecting the components that circulate coolant to and from the engine. Moulded ...

Body Moulding Retainer Clip, a lantern-type fastener for the vehicle's exterior trim. The clip secures exterior body mouldings - such as the rocke...

Oil Cooler Tube carries engine oil through the oil cooler circuit. The tube connects the engine oil system to the oil cooler, routing oil to be co...

O-ring for the variable valve timing (VVT) solenoid, part of the timing gear assembly at the front of the engine. The solenoid meters oil flow to ...

Inlet Manifold Gasket for the left-hand cylinder bank of the 5.0 litre V8 petrol engine (AJ133). It seals the joint between the inlet manifold and ...

Vacuum Pump Seal - sealing ring between the engine-driven vacuum pump and its mounting face on the engine, forming part of the brake servo vacuum c...

O-Ring - Radiator Hose

Intercooler to Inlet Manifold Gasket from the charge air induction system of the supercharged 5.0L V8 petrol engine (AJ133). The supercharger and ...

Gasket - Oil Cooler seals the engine oil cooler to its mounting face, within the Oil Cooler and Filter assembly. It maintains the integrity of the...

Front Brake Caliper Attachment Kit - the caliper fitting hardware for the front disc brake assembly. The kit contains the brake pad clips and the ...

Brake Caliper Locating Pin Kit for the sliding brake caliper. The guide pins let the caliper float on its carrier bracket so both brake pads wear ...

Ignition Coil for the 2.0L four-cylinder petrol engine (AJ200 / AJ20P4, including PHEV). This is a coil-on-plug unit that mounts directly on the sp...

Piston Ring Set for the 5.0L V8 AJ133 petrol engine, supplied at standard bore size. The ring pack seals the combustion chamber against the cylind...

Brake Caliper Guide Pin Dust Cover for the front and rear brake calipers. The boot fits over the caliper guide pin and seals against the carrier b...

Camshaft Position Sensor mounted in the timing gear cover, reading the toothed target on the camshaft drive to give the engine control module a dir...

Thermostat Housing for the 5.0-litre AJ133 V8 petrol engine, part of the engine cooling circuit. The housing seats the coolant thermostat and form...

Inlet Manifold Gasket - 5.0 V8 - RH seals the inlet manifold to the cylinder head on the right-hand bank of the 5.0 litre V8 petrol (AJ133) engine,...

Inlet Valve - cylinder head inlet (induction) valve for the 5.0L V8 AJ133 supercharged petrol engine. The inlet valve admits the intake charge int...

Piston assembly - piston for the AJ133 5.0L supercharged V8 petrol engine, in the standard (nominal production) bore size. The piston runs in the ...

Piston - 0.50 mm Oversize for the 2.0-litre Ingenium (AJ200D / 204DTD) diesel engine. An engine-rebuild piston machined 0.50 mm over the standard ...

Water Pump for the 3.0L supercharged V6 and 5.0L V8 petrol (AJ133) engines. The pump circulates coolant through the engine block, cylinder heads a...

Camshaft Sprocket is a timing-drive gear in the valve train of the 2.0L Ingenium diesel engine (AJ200D). Mounted on the end of the camshaft, it is...

Brake Actuator - electric parking brake (EPB) actuator, part of the electronic parking brake assembly. The motor-driven actuator applies and relea...

Front Axle Shaft - the front propshaft that transmits drive from the transfer case output to the front differential, feeding torque to the front ax...

Radiator is the primary heat exchanger of the Engine Cooling System, transferring heat from the engine coolant to the air drawn through the front c...

Brake Vacuum Pump, the auxiliary vacuum source for the brake servo on petrol engines. Petrol engines - particularly direct-injection and superchar...

Fuel Pump - high-pressure, engine-mounted fuel injection pump within the direct-injection fuel system on petrol engines. Driven off the engine, it...

Fan Assembly

Spark Plug Well Gasket seals the spark plug aperture in the camshaft (valve) cover on the right-hand cylinder head bank. It prevents engine oil fr...

Spark Plug Gasket - LH seals the spark plug apertures in the left-hand cylinder head cover (cam cover). It keeps engine oil out of the spark plug w...