Range Rover Classic Parts

Bolt - Lower Steering Shaft UJ is the M8 x 35 mm clamp bolt that secures the universal joint at the lower steering shaft, within the steering colum...

Grommet - rubber sealing grommet, 3/4 inch overall diameter with 1/8 inch centre hole. Used to seal and protect wiring cables where they pass thro...

Banjo Bolt secures the breather pipe to an axle, gearbox or transfer case housing. The bolt is drilled through its shank and head so that, clamped...

Drain Plug - Coolant - Cylinder Block is the threaded plug that seals the coolant drain port in the cylinder block, providing a controlled drain po...

Trunnion

Pan Head Screw, M4 x 12mm. Metric pan head screw for use across a range of Land Rover assemblies, including brake system and electrical components.

Front Coil Spring - front suspension coil spring, seated between the axle spring pad and the chassis spring turret to support the vehicle and contr...

Bolt 3/8" x 2"

Front Air Grille covers the fresh air intake at the base of the windscreen, forming part of the fresh air system that feeds the heater and ventilat...

Fuel Sedimentor is a water and sediment trap in the diesel fuel supply line, installed upstream of the fuel filter and injection pump. Fuel passes...

Sedimentor Drain Plug Seal for the sedimentor in the diesel fuel supply. The sedimentor separates water and heavier contaminants from the fuel ahea...

Countersunk Screw - M6 x 12mm is a metric fastener used across multiple assemblies on Land Rover vehicles, including brake disc and drum retention ...

Nutsert - 5/16" UNF is a blind rivet nut (rivnut) with a 5/16" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal ...

Steering Stop Bolt - M12 x 50mm shouldered hex-head bolt for the front axle steering lock assembly. This bolt sets the maximum steering lock angle...

Taper Roller Bearing for the front output shaft of the LT230 transfer box. Installed within the LT230 transfer case differential lock and output s...

Cable Tie, Panel Fixing: grey cable tie strap with a panel fixing, 4.6 x 165 mm.

Head Gasket - seals a single cylinder between the cylinder head and the engine block on the VM 4-cylinder turbo diesel. The VM diesel uses a separ...

Pulley

Rocker Cover O-Ring for the VM four-cylinder turbo diesel engine, sealing the rocker (cam) cover to the cylinder head. It maintains the oil-tight ...

Spire Nut, a J-type sheet-metal spring nut (also known as a speed nut) used to secure trim, panels and fittings. The nut clips over a panel edge o...

Screw 3/8" UNC x 1-1/2" used to secure the starter motor to the engine block on Rover V8 petrol engine applications. This is a 3/8 inch Unified Nat...

clamp exhaust pipe RRclassic (with twin exhaust pipes)

Fuse - 10A for Land Rover electrical systems. This 10A fuse protects individual circuits in the vehicle fuse box from overcurrent damage.

Screw - a No. 10 x 1" pan-head self-tapping screw used across interior and door assemblies. It secures the window regulator and door glass channel...

Polyurethane Suspension Bush Kit A complete polyurethane bush set that replaces the original rubber suspension bushes across the chassis-mounted su...

Shock Absorber Bush Kit for the mounting points of Terrafirma TS-series shock absorbers. The kit provides the hardware required to replace worn bu...

Hose Clip is an adjustable worm-drive band clip that clamps a flexible hose onto its spigot or fitting. It tightens over the hose with a screw-dri...

Fuse rated at 15A for the vehicle electrical system. Fitted in the fusebox to protect a circuit rated at 15 amps, the fuse breaks the connection w...

Drive Screw is a countersunk-head self-tapping screw used to secure body and interior trim components. The self-tapping thread cuts its own mating...

Sump Plug for the engine oil sump drain. Fitted to the sump drain port and removed at each oil change to drain the engine oil. The sealing washer ...

Cylinder Head Bolt - a 7/16" UNC x 2.71" medium-type bolt for the Rover V8, part of the cylinder head fixings. This is the medium-length head bolt...

Bolt - M10 x 130mm is a hex-headed metric fastener with a 10 mm nominal thread diameter and a 130 mm shank length. It serves as a general mounting...

Locking Wheel Nut Set for alloy wheels that use the original alloy wheel nuts, securing the road wheels against theft. The set includes 5 locking ...

Viscous Fan Assembly for the engine cooling system, mounting to the viscous coupling unit on the front of the engine. This 16", 7-blade white fan ...

Plain Washer - Large 5/16" is a large plain washer for use with 5/16" fastenings, providing load distribution beneath bolt heads and nuts across La...

Rivet is a body fixing used to secure sheet-metal panels, wheelarch liners and trim to the vehicle structure. It forms a permanent, vibration-resi...

Sedimentor Drain Plug with Seal for the diesel fuel filter assembly. Fitted at the base of the sedimentor bowl, this plug allows the bowl to be dr...

heavy duty spring front RR/disco pair, like DA4201 and TF014.

Nut An M4 hexagonal plain nut. A general-purpose metric fastener used across a wide range of assemblies. Takes a 7 mm spanner.

Programmable Wiper Delay Relay is a direct replacement for the standard AMR2341 relay in the front wiper circuit, providing a user-adjustable inter...

Winch Remote Control operates an electric recovery winch wirelessly, allowing the operator to stand clear of the winch line during recovery. Wirel...

Fitment: All non ABS models (VIN) JA032851 on to (axle) 38L03120B. 39L05552B. 42L00521B. 43L18579B All Models From (A)57L00001B To (A)57L05188B0

Front Wiper Motor for the windscreen wiper assembly. The motor drives the wiper linkage and wheelboxes that sweep the front wiper blades across the...

Air Spring - Front - pneumatic suspension bellows unit for the front axle of the Range Rover Classic Electronic Air Suspension (EAS) system. The a...

Bump Stop limits suspension travel within the suspension assembly, cushioning the contact between the axle and chassis at the extremes of wheel mov...

Upper Link Bush Set - Polyurethane for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. Supplied as a set of two ...

Windscreen Seal is a rubber glazing seal fitted around the windscreen aperture. It retains the windscreen glass in the body aperture and seals the...

Heater Hose for the 200TDi engine cooling and heating circuit. This hose routes coolant from the engine cooling system to the cabin heater matrix,...