Range Rover Evoque L551 Parts

Wheel Centre Cap - a black alloy-wheel centre cap carrying the Land Rover oval in green and silver. It presses into the centre bore of an alloy wh...

Bolt and Washer - an M8 x 24mm bolt supplied with a washer, used as a general-purpose fixing across several Land Rover assemblies. The washer spre...

Wheel Centre Cap - set of four alloy wheel centre caps in Titan Silver. The centre cap clips into the hub bore of an alloy wheel, covering the hub...

EGR Cooler Filter for the low-pressure exhaust gas recirculation circuit of the 2.0L I4 Ingenium diesel engine. The low-pressure EGR system draws ...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Wheel Centre Cover fits into the central hub bore of an alloy wheel, concealing the hub and wheel-mounting hardware behind a finished cap that clip...

Injector Refit Kit supplying the seals needed to refit a fuel injector on petrol engines. It restores the sealing interface between the injector an...

Accessory Drive Belt - multi-rib belt driving the engine's front-end accessories. Transmits crankshaft rotation to the belt-driven ancillaries wit...

Timing Chain Tensioner Arm bears against the timing chain within the timing drive assembly, providing the face through which the tensioner applies ...

Connecting Rod Bolt secures the connecting rod big-end cap to the connecting rod within the crankshaft, pistons and bearings assembly. The bolt cl...

Lithium-Ion Battery - the backup battery for the Telematics Control Unit (TCU). It supplies backup power to the telematics control unit so the uni...

Bolt for the camshaft timing gear, part of the Ingenium engine timing drive. It retains the timing sprocket to the camshaft, transferring drive fr...

Timing Chain Guide - LH Primary - a fixed guide in the timing drive assembly of the 2.0L four-cylinder Ingenium petrol engine (AJ200 / AJ20P4), inc...

DEF Injector Refit Kit

Timing Cover Blanking Plug - threaded plug that closes an aperture in the front timing cover of the 2.0L Ingenium petrol engine (AJ200 / AJ20P4, al...

O-Ring - VVT Solenoid Cover, 47 mm, sealing the variable valve timing solenoid cover to the cylinder head on Ingenium engines - 2.0L AJ20P and AJ20...

Cable Connector - an electrical connector used in the vehicle wiring harness. The connector forms the termination between a harness cable and its ...

Mini Relay with four blade terminals, rated at 40 amp. A four-terminal mini relay switches a single normally-open high-current circuit under the c...

Mini Relay with four blade terminals, rated at 70 amp, grey housing. A four-terminal mini relay switches a single normally-open high-current circu...

Glow Plug - cold-start pre-heating system of the 2.0L Ingenium AJ200 four-cylinder turbo diesel engine. Threads into the cylinder head, one per cy...

Timing Chain Guide, Lower Primary from the front timing gear assembly. It bears against the primary drive chain on the run between the crankshaft ...

Timing Gear Bolt - special-form fastener used in the timing drive assembly at the front of the Ingenium petrol engine. It is one of the fixings th...

Exhaust Mounting Rubber (insulator/hanger) in the exhaust system suspension. Supports the exhaust system on its mounting brackets, isolating exhau...

Timing Chain Guide locates and supports the timing chain within the timing drive assembly. It maintains correct chain alignment along its run, con...

Timing Chain Guide locates and supports the timing chain within the timing drive assembly. It maintains correct chain alignment along its run, con...

Sealing Washer is the fuel injector sealing washer for the Ingenium diesel engine (2.0L and 3.0L AJ20 / AJ21 diesel). It seats at the base of the ...

Nut used in exterior body panel and trim fixings. Secures body components such as the luggage compartment door finisher, radiator grille and bumpe...

O-Ring for the Exhaust Gas Recirculation (EGR) circuit. This seal maintains a gas-tight joint within the EGR section, sealing the connection betwe...

Exhaust Gas Recirculation Gasket seals the exhaust gas recirculation (EGR) connection on the left-hand side, maintaining a gas-tight joint within t...

Circuit Breaker installs within the electrical power distribution system, protecting a circuit against overcurrent by interrupting the supply when ...

Intake Manifold Gasket seals the joint between the intake manifold and the cylinder head, within the air intake assembly. It maintains an airtight...

Sealing Ring sealing a joint within the engine timing gear covers. This O-ring seals a connection at the timing cover assembly, maintaining oil-ti...

Cover Gasket for the upper timing chain cover. It seals the joint between the upper timing chain cover and the engine, maintaining an oil-tight se...

Valve Stem Seal for the cylinder head valvetrain. It seals around the valve stem where it passes through the valve guide, controlling oil entry in...

Timing Chain Guide for the engine timing gear. It supports and locates the timing chain along its run, controlling the chain path and reducing vib...

Timing Chain Guide for the engine timing gear. It supports and locates the timing chain along its run, controlling the chain path and reducing vib...

Timing Chain Tensioner Arm for the engine timing gear. It bears against the timing chain and transmits the tensioner load to take up slack and mai...

Special Bolt for the engine timing gear assembly. It secures a component within the timing gear drive. Fitted to 2.0-litre diesel Ingenium engines...

Idler Pulley for the accessory drive belt system, 65 mm in diameter. It guides the accessory (auxiliary) drive belt across its run, maintaining be...

Bolt securing the fuel injector and high-pressure fuel pipe assembly on the engine fuel system. It clamps the injector and high-pressure pipe unio...

Water Outlet Tube forming the coolant outlet connection at the cylinder head, part of the engine cooling circuit. It carries coolant from the cyli...

O-Ring for the turbocharger of the 2.0L I4 diesel (AJ200) engine, sealing the upper turbocharger-to-pipe joint (14.3 x 2.4 mm). The O-ring seals t...

Oil Drain Plug for the engine oil pan (sump). Threaded into the base of the oil pan, it seals the oil drain point and is removed to drain the engi...

Cylinder Head Bolt with hex head, for the 2.0L I4 diesel (AJ200) engine. The bolt secures the cylinder head to the engine block, providing the cla...

Turbocharger Gasket for the exhaust turbocharger assembly on the 2.0L I4 diesel (AJ200) engine, sealing the turbocharger outlet to the exhaust fron...