Range Rover Evoque L551 Parts

Bolt - M8 x 50 - Torx is an M8 threaded fastener, 50 mm long, with a Torx drive head. It is used as a general-purpose fixing across a range of bod...

Wheel Centre Cap - set of four alloy wheel centre caps in Titan Silver. The centre cap clips into the hub bore of an alloy wheel, covering the hub...

Washer Fluid Level Sensor for the windscreen washer system. The sensor fits into the washer fluid reservoir and monitors the volume of fluid remai...

Wheel Centre Cover fits into the central hub bore of an alloy wheel, concealing the hub and wheel-mounting hardware behind a finished cap that clip...

Injector Refit Kit supplying the seals needed to refit a fuel injector on petrol engines. It restores the sealing interface between the injector an...

Blanking Plug - timing chain cover, supplied with its O-ring. Seals a machined service aperture in the timing chain cover of the Ingenium engine f...

Bolt for the camshaft timing gear, part of the Ingenium engine timing drive. It retains the timing sprocket to the camshaft, transferring drive fr...

Antifreeze and Coolant Concentrate - red, extended-life engine coolant concentrate for the cooling system, supplied in a 1 litre container. The fl...

Spark plug for the ignition system of the Ingenium petrol engine range - 1.5L AJ20P3, 2.0L AJ20P4 / AJ200P and 3.0L AJ20P6 / AJ22P6, including plug...

DEF Injector Refit Kit

Rear Crankshaft Oil Seal - the main oil seal at the flywheel end of the crankshaft, part of the crankshaft sealing arrangement on the Ingenium engi...

Mini Relay with four blade terminals, rated at 70 amp, grey housing. A four-terminal mini relay switches a single normally-open high-current circu...

Valve stem seal for the cylinder head valve train. The seal locates on the valve guide and wipes the valve stem as it reciprocates, metering the s...

Sealing Washer is the fuel injector sealing washer for the Ingenium diesel engine (2.0L and 3.0L AJ20 / AJ21 diesel). It seats at the base of the ...

Nut used in exterior body panel and trim fixings. Secures body components such as the luggage compartment door finisher, radiator grille and bumpe...

Adhesive and Sealer is a glass bonding adhesive and sealer used to seat and seal fixed automotive glazing to the body. It bonds and seals the wind...

Valve Stem Seal for the cylinder head valvetrain. It seals around the valve stem where it passes through the valve guide, controlling oil entry in...

Oil Drain Plug for the engine oil pan (sump). Threaded into the base of the oil pan, it seals the oil drain point and is removed to drain the engi...

Metal Name Plate is an exterior badge fitted to the bodywork. It mounts to the body panel as a model or trim identifier and forms part of the vehic...

Brake Fluid for the hydraulic braking and clutch actuation system, supplied in a 1 litre container. A DOT 4 low-viscosity (ESL) fluid formulated f...

Automatic Transmission Fluid (ATF) for the automatic gearbox and power steering circuit. Specified as the transmission and power steering fluid to...

Wheel Cover set, fitted over the road wheels. The covers clip over the wheels to give a finished appearance and shield the wheel face from road di...

Wheel Cover for the road wheel. The cover fits over the wheel to give a finished appearance and shield the wheel face from road dirt and brake dus...

Diesel Exhaust Fluid (AdBlue) for diesel vehicles fitted with a selective catalytic reduction (SCR) exhaust after-treatment system. The fluid is h...

Front Crankshaft Oil Seal - radial lip seal in the cylinder block and front cover assembly, sealing the crankshaft nose where it passes through the...

Axle Oil 75W-90 is a hypoid gear oil for the front and rear differentials and final drive units. The 75W-90 grade lubricates the crown wheel and p...

Flanged Nut with an integral flange that spreads the clamping load and helps resist loosening, removing the need for a separate washer. Used to se...

Retaining Clip is a fastening clip used in the radiator grille and front bumper assembly. It secures the grille and front bumper trim components t...

Clip - retaining clip for the radiator grille and front bumper assembly. It secures the grille and bumper components to their mountings.

Bumper Retainer Nut - a push-in retaining nut used in the front bumper, radiator grille and rear bumper assemblies. The retainer clips into a pres...

Tyre Pressure Sensor - wheel-mounted pressure and temperature sensor for the Tyre Pressure Monitoring System (TPMS). Mounted at the valve position...

Exterior mirror motor - left-hand side glass adjustment motor within the door mirror head. The motor sits behind the mirror glass and drives the g...

Drive Belt Tensioner - automatic tensioner for the front-end accessory drive on the AJ20 Ingenium petrol engine range. A spring-loaded pivoting ar...

Camshaft Sprocket for the timing drive of the Ingenium engine family - the 2.0L and 3.0L diesel and 3.0L petrol units. Mounted on the end of the ca...

Purge Control Valve - evaporative emission (EVAP) control system. The valve sits in the line between the activated carbon canister and the engine ...

Bonnet Latch for the bonnet (hood) closure mechanism. It engages the bonnet striker to hold the bonnet closed and releases it when operated, formin...

Screw and Washer - M5 x 20 is a self-tapping fastener with a captive washer, an M5 thread, 20 mm length and a hex head. It secures body panels, sp...