Range Rover Evoque L551 Parts

Cable Connector - an electrical connector used in the vehicle wiring harness. The connector forms the termination between a harness cable and its ...

Front Brake Sensor Wiring Bracket - mounting bracket for the brake pad wear sensor lead at the front disc brake and caliper assembly. The bracket ...

Coolant Bypass Tube - a rigid coolant transfer pipe in the cooling circuit of the 2.0L AJ20P4 four-cylinder petrol engine. The tube carries coolan...

Front Wiper Blade - Driver's Side is the driver's side blade of the front windscreen wiper system in left-hand drive configuration. It is the long...

Mini Relay with four blade terminals, rated at 40 amp. A four-terminal mini relay switches a single normally-open high-current circuit under the c...

Mini Relay with four blade terminals, rated at 70 amp, grey housing. A four-terminal mini relay switches a single normally-open high-current circu...

Front Wiper Blade for the windscreen wiper system, mounting to the wiper arm on the passenger side of left-hand drive vehicles. The blade carries ...

Glow Plug - cold-start pre-heating system of the 2.0L Ingenium AJ200 four-cylinder turbo diesel engine. Threads into the cylinder head, one per cy...

Valve stem seal for the cylinder head valve train. The seal locates on the valve guide and wipes the valve stem as it reciprocates, metering the s...

Timing Chain Guide, Lower Primary from the front timing gear assembly. It bears against the primary drive chain on the run between the crankshaft ...

Exhaust Clamp for the 2.0L Ingenium diesel exhaust system (AJ200D / AJ20D4). The clamp secures the front section joint of the exhaust, holding the...

Timing Gear Bolt - special-form fastener used in the timing drive assembly at the front of the Ingenium petrol engine. It is one of the fixings th...

Coolant Hose - Overflow - moulded hose in the engine cooling system, forming part of the overflow circuit between the cooling circuit and the coola...

Front Shock Absorber Insulator from the front suspension strut assembly. It sits at the spring seat between the coil spring and the strut, isolati...

Timing Gear Bolt - a fixing bolt in the engine timing drive, retaining a timing gear. It secures the timing gear on the 2.0L four-cylinder AJ200 p...

Exhaust Mounting Rubber (insulator/hanger) in the exhaust system suspension. Supports the exhaust system on its mounting brackets, isolating exhau...

O-Ring - seals a joint in the thermostat housing and its associated coolant connections. Fitted to the 2.0L four-cylinder AJ200/AJ20 petrol and di...

Timing Chain Guide locates and supports the timing chain within the timing drive assembly. It maintains correct chain alignment along its run, con...

Timing Chain Guide locates and supports the timing chain within the timing drive assembly. It maintains correct chain alignment along its run, con...

Sealing Washer is the fuel injector sealing washer for the Ingenium diesel engine (2.0L and 3.0L AJ20 / AJ21 diesel). It seats at the base of the ...

Nut used in exterior body panel and trim fixings. Secures body components such as the luggage compartment door finisher, radiator grille and bumpe...

O-Ring for the Exhaust Gas Recirculation (EGR) circuit. This seal maintains a gas-tight joint within the EGR section, sealing the connection betwe...

Rear Crankshaft Oil Seal for the 2.0L AJ200 engine. This seal fits around the rear of the crankshaft where it exits the cylinder block, retaining ...

O-Ring for the Exhaust Gas Recirculation (EGR) circuit, 60mm. This seal maintains a gas-tight joint within the EGR section, sealing the connection...

Bearing Cap Bolt with hex head for the crankshaft main bearing assembly of the AJ200 / AJ20 four-cylinder Ingenium engines. Secures the crankshaft...

Exhaust Gas Recirculation Gasket seals the exhaust gas recirculation (EGR) connection on the left-hand side, maintaining a gas-tight joint within t...

Circuit Breaker installs within the electrical power distribution system, protecting a circuit against overcurrent by interrupting the supply when ...

Energy-Absorbing Foam Pad is fitted within the fuel filter assembly, cushioning the filter and absorbing vibration and impact energy. Supplied for...

Adhesive and Sealer is a glass bonding adhesive and sealer used to seat and seal fixed automotive glazing to the body. It bonds and seals the wind...

Intake Manifold Gasket seals the joint between the intake manifold and the cylinder head, within the air intake assembly. It maintains an airtight...

Seal for the oil filter to oil cooler connection, part of the oil cooler and filter assembly. This O-ring seals the joint between the oil filter h...

Sealing Ring sealing a joint within the engine timing gear covers. This O-ring seals a connection at the timing cover assembly, maintaining oil-ti...

Cover Gasket for the upper timing chain cover. It seals the joint between the upper timing chain cover and the engine, maintaining an oil-tight se...

Valve Stem Seal for the cylinder head valvetrain. It seals around the valve stem where it passes through the valve guide, controlling oil entry in...

Timing Chain Guide for the engine timing gear. It supports and locates the timing chain along its run, controlling the chain path and reducing vib...

Timing Chain Guide for the engine timing gear. It supports and locates the timing chain along its run, controlling the chain path and reducing vib...

Timing Chain Tensioner Arm for the engine timing gear. It bears against the timing chain and transmits the tensioner load to take up slack and mai...

Special Bolt for the engine timing gear assembly. It secures a component within the timing gear drive. Fitted to 2.0-litre diesel Ingenium engines...

Idler Pulley for the accessory drive belt system, 65 mm in diameter. It guides the accessory (auxiliary) drive belt across its run, maintaining be...

Exhaust Manifold Gasket sealing the exhaust manifold and turbocharger joint. The same gasket serves both the exhaust manifold and the turbocharger...

Bolt securing the fuel injector and high-pressure fuel pipe assembly on the engine fuel system. It clamps the injector and high-pressure pipe unio...

Water Outlet Tube forming the coolant outlet connection at the cylinder head, part of the engine cooling circuit. It carries coolant from the cyli...

O-Ring for the turbocharger of the 2.0L I4 diesel (AJ200) engine, sealing the upper turbocharger-to-pipe joint (14.3 x 2.4 mm). The O-ring seals t...

Oil Drain Plug for the engine oil pan (sump). Threaded into the base of the oil pan, it seals the oil drain point and is removed to drain the engi...

Cylinder Head Bolt with hex head, for the 2.0L I4 diesel (AJ200) engine. The bolt secures the cylinder head to the engine block, providing the cla...