for Discounts / VAT
for Discounts & Correct VAT
Parts for the Range Rover L322, the third-generation flagship produced from 2002 to 2012. This collection covers all three powertrain eras: the BMW-engined pre-facelift (2002 to 2005), the Jaguar-era facelift (2006 to 2009), and late production (2010 to 2012).
24v dsl long belt
"Land Rover" Rear Decal Badge A self-adhesive lettered name plate forming part of the exterior rear badging, applied to the rear bodywork. The let...
View full detailsLocknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...
View full detailsBlanking Plug for closing an unused 13 mm (1/2") hole in body or trim panelling. A push-in plastic plug used to blank off redundant or open apertu...
View full detailsFuel Tank Adaptor Ring secures the in-tank fuel pump and sender unit assembly into the aperture on the top of the fuel tank. The ring locks the pu...
View full detailsA-Pillar Trim Clip A retaining clip used in the interior A-pillar trim assembly. It secures the A-pillar trim panel to the body structure alongsid...
View full detailsLand Rover Grille Name Plate - Black & Silver - front grille name plate carrying the Land Rover lettering, finished in black and silver. Mount...
View full detailsTorx Screw - 4.8 × 25mm for use in Land Rover body and trim assemblies. A metric Torx-head screw, 4.8mm diameter × 25mm length, for use where Torx...
View full detailsLand Rover Oval Name Badge - exterior identification emblem carrying the Land Rover name in gold lettering on a green ground. Fitted to the front ...
View full detailsAir Cleaner Ring for the Range Rover L322 intake assembly. This sealing ring fits within the air cleaner housing on the BMW M62 B44 4.4-litre V8 p...
View full detailsClip is a retaining clip in the front windscreen wiper linkage. It secures the wiper motor and linkage assembly, holding the linkage components to...
View full detailsOil Cooler Gasket for the AJ-Series V8 petrol engine, sealing the oil cooler and filter housing to the cylinder block. This gasket forms the oil-t...
View full detailsCoolant Hose forms part of the heater line within the engine cooling system, routing coolant between the engine and the heater matrix. Supplied co...
View full detailsWater Outlet Connection (Upper) for the 4.4L DOHC V8 turbo-diesel (TDV8) engine. Part of the thermostat and coolant housing assembly, it carries co...
View full detailsTiming Gear Bolt is the hex-head flanged bolt that retains the upper timing gear on the valve-timing drive. It secures the upper gear against the ...
View full detailsTrim Clip is an interior trim fixing that retains the A-pillar trim panel against the body structure. Depending on application it also serves as t...
View full detailsCylinder Head Bolt for the cylinder head assembly on TDV6 and TDV8 diesel engines. The bolt secures the cylinder head to the engine block, clamping...
View full detailsFront Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...
View full detailsHex Flange Nut - a flanged hexagonal nut used as a general threaded fastener across multiple vehicle assemblies. The integral flange spreads the c...
View full detailsClip is a locking retaining clip in the front windscreen wiper linkage. It locks the wiper linkage connection, securing the motor and linkage asse...
View full detailsPower Steering Hose Sealing Washer - seals the union between a power steering supply or return hose and its mating port in the steering hydraulic c...
View full detailsSpecial Stud for the Range Rover L322 bonnet and tailgate area fixings. This stud is used in the bonnet assembly and luggage compartment door fixi...
View full detailsCoolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...
View full detailsAir Suspension Reservoir for the Electronic Air Suspension (EAS) system. This pressure vessel (accumulator) stores a reserve of compressed air, en...
View full detailsEGR Thermostat Assembly that regulates coolant flow through the exhaust gas recirculation (EGR) cooler on the 2.7-litre V6 and 3.6-litre V8 diesel ...
View full detailsWheel Centre Cap for the road wheel, fitting into the centre bore of the rim to cover the hub. Finished in silver with a black logo. The cap conce...
View full detailsOil Seal for the rear differential, part of the rear axle final drive assembly. It seals the rotating shaft where it exits the differential housin...
View full detailsHexagon Nut for use in electrical system assemblies.
Oval LAND ROVER Badge - gold lettering on a green background - for the tailgate. This is the classic oval "LAND ROVER" name badge fitted to the ex...
View full detailsLuggage Hook is a black loadspace hook mounted to the loadspace quarter trim. It provides an anchor point in the load area for securing luggage or...
View full detailsIdler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...
View full detailsBonnet Alarm Switch - plunger switch in the perimeter alarm and anti-theft circuit, sensing whether the bonnet is closed. It mounts on the inner w...
View full detailsHeight Sensor Jumper Lead for the electronic air suspension system. This connecting lead links a ride-height sensor to the chassis wiring harness,...
View full detailsMicroswitch Assembly - switch unit used in the power deployable running board (side step) accessory circuit. It provides the switched contact sign...
View full detailsDual - Bulb
Front Direction Indicator Bulb - 12V 28W, serving the indicator position within the front lamp assembly. At 28W this bulb is rated above the more ...
View full detailsGear Selector Linkage Bush in the floor gear-change assembly of the ZF 6HP26 / 6HP28 6-speed automatic transmission. The bush forms the pivot at t...
View full detailsBolt - threaded fastener used in the rear axle assembly. It is one of the fixings securing rear axle components to the differential housing.
Rear Output Shaft Oil Seal for the ZF 6HP26 and 6HP28 six-speed automatic transmission. It seals the point where the output shaft leaves the rear ...
View full detailsScrew used on the external components of the ZF 5HP24 five-speed automatic transmission. It secures externally mounted hardware to the transmissio...
View full detailsSpring Washer used in the floor-mounted gear change assembly of the ZF 6-speed automatic transmission. It is fitted under the fastener securing th...
View full detailsBolt for the floor-mounted gear change assembly of the ZF 6-speed automatic transmission. It secures the gear change mechanism to its mounting on ...
View full detailsBulb Holder - left-hand rear lamp bulb carrier, forming the electrical backplate of the rear lamp assembly. The carrier clips into the back of the...
View full detailsBulb Holder - right-hand rear lamp bulb carrier, forming the electrical backplate of the rear lamp assembly. The carrier clips into the back of th...
View full detailsNumber Plate Lamp Lens - clear lens for the rear licence plate lamp mounted in the luggage compartment door. The lens clips into the lamp housing ...
View full detailsRear Lamp - LH is the tailgate-mounted reverse lamp for the left-hand side, part of the rear lighting circuit. It mounts in the tailgate panel bes...
View full detailsRear Lamp Assembly is the tailgate-mounted reverse lamp for the right-hand side, part of the rear lighting circuit. It mounts in the tailgate pane...
View full detailsAsy Lamp
The Range Rover L322 is the third-generation Range Rover, produced at Land Rover's Solihull plant from model year 2002 through to 2012, with 293,494 examples built across the full run. It succeeded the Range Rover P38 (1994-2001) and was itself replaced by the Range Rover L405 (2013-2022). It was the first Range Rover to use a monocoque unibody construction and the first to carry four-wheel independent air suspension as standard. Three distinct powertrain eras define the L322, and parts fitment often depends on knowing which era your vehicle belongs to.
The pre-facelift era (2002 to 2005) used the BMW M62TUB44 4.4-litre V8 petrol and the BMW M57D30 3.0-litre Td6 inline-six diesel, paired with a five-speed GM 5L40-E automatic (Td6) or a five-speed ZF 5HP automatic (V8). The facelift era (2006 to 2009) replaced both with Jaguar-sourced engines: the AJ41 4.4-litre V8 and the AJ34S 4.2-litre supercharged V8 for petrol, and the AJD-V8 3.6-litre twin-turbo TDV8 for diesel from model year 2007, all paired with the ZF 6HP six-speed automatic. Late production (2010 to 2012) introduced the AJ133 5.0-litre V8 family in naturally aspirated and supercharged form for petrol, and the larger AJD-V8 4.4-litre TDV8 diesel paired with an eight-speed ZF 8HP automatic.
Parts that fit a 2004 Td6 will not necessarily fit a 2008 TDV8. Engine ancillaries, transmission service components, cooling system parts, and fuel system components are all era-specific. Confirming your engine code and transmission type before ordering is the most reliable way to avoid incorrect fitment.
Use the table below to identify which era your L322 belongs to before selecting engine-specific parts.
| Era | Model Years | Petrol Engines | Diesel Engine | Transmission |
|---|---|---|---|---|
| Pre-facelift (BMW era) | 2002 to 2005 | 4.4 BMW M62 V8 | 3.0 BMW M57 Td6 I6 | GM 5L40-E (Td6), ZF 5HP (V8) |
| Facelift (Jaguar era) | 2006 to 2009 | 4.4 Jaguar AJ41 V8, 4.2 Jaguar AJ34S S/C V8 | 3.6 AJD-V8 TDV8 (from 2007 MY) | ZF 6HP |
| Late production | 2010 to 2012 | 5.0 AJ133 V8, 5.0 AJ133 S/C V8 | 4.4 AJD-V8 TDV8 | ZF 6HP, ZF 8HP (4.4 TDV8) |
The 3.0 Td6 diesel continued into the 2006 model year before being replaced by the 3.6 TDV8 from model year 2007. Terrain Response was introduced from model year 2007.
The L322 underwent significant mechanical changes across its production run. Registration year alone is not always sufficient to confirm your exact specification, particularly for vehicles registered during the 2005 to 2006 transition period, when both the BMW M62 and the Jaguar AJ41 V8 were in production simultaneously. Some early 2006 registrations carry the outgoing BMW engine.
The most reliable method is to use your 17-digit VIN. The VIN is stamped on the door jamb plate, at the base of the windscreen, and on your vehicle registration document. The tenth character encodes the model year, and the full VIN can be used to confirm the engine code and specification via a Land Rover dealer or authorised VIN decoder.
Land Rover’s powertrain specifications for the L322 can vary significantly by production month. To ensure 100% fitment, we recommend using a [VIN Decoder] to verify your model year and engine code before ordering.
Parts CategoriesThe L322 collection covers the full range of replacement and maintenance parts for all three powertrain eras. Categories stocked include engine components (gaskets, seals, ancillaries, cooling system parts), transmission service items (filter kits, fluid, solenoids, valve body components), air suspension components (compressors, air struts, valve blocks, sensors, relay units), braking system parts (discs, pads, calipers, brake lines, sensors), steering and suspension components (arms, bushes, ball joints, drop links, anti-roll bar components), drivetrain and propshaft parts, electrical components (relays, sensors, switches, lamps), fuel system parts, and body and trim components.
Air suspension parts deserve particular attention on the L322. The independent air suspension system was standard across the entire production run from 2002 to 2012. Compressor failure, valve block deterioration, and air strut leaks are among the most frequently replaced component groups. Parts within this category are available in OEM and aftermarket specification for the full model year range.
Quality TiersEvery part on this page is graded Genuine, OEM, or aftermarket and labelled accordingly on the product listing. Genuine carries Land Rover part numbers and packaging; OEM is the same component from the original supplier without the official channel markup; aftermarket is an independently manufactured alternative. For the full definition of each tier, see the Range Rover parts collection.
EU Stock and DispatchBudget Parts stocks Range Rover L322 parts in the Netherlands and dispatches across the EU. The full L322 collection is available to private owners, independent workshops, and trade buyers across European markets.
Budget Parts operates a wholesale portal for registered independent Land Rover workshops and trade buyers across the EU. The portal provides trade pricing, account-based ordering, and direct technical support. If you manage a workshop or operate as a trade parts buyer, you can access trade terms or register your account via the Wholesale Portal.
For the full Range Rover model family including all generations, return to the Range Rover Parts collection.
Technical GuidesThe articles below are published guides that provide diagnostic and technical context relevant to Range Rover L322 owners and workshops. They support your parts decision rather than being read on this page.
The primary fault reference for the L322 generation. Covers air suspension failure patterns, transmission behaviour, cooling system failures, and fuel system issues across the BMW and Jaguar powertrain eras. Read this before ordering parts if you are diagnosing a problem rather than completing a scheduled service.
Range Rover L322 faults and fixes guide →Relevant to the L322 4.4 V8 petrol and TDV8 diesel variants, where cooling system failures are a known service interval concern. Covers how to identify the root cause before selecting replacement parts, including thermostat, coolant pump, and radiator assessment.
Range Rover L322 overheating diagnosis →Covers driveline diagnosis applicable to the L322 four-wheel-drive system, including propshaft vibration, CV joint wear, and transfer case output assessment. Useful before ordering drivetrain components for the L322.
Range Rover L322 driveline diagnosis →The Range Rover L322 covers model years 2002 to 2012. Production at the Solihull plant ran from 2001, with the first customer vehicles delivered as 2002 model year examples. The final L322 models were produced in 2012, with the fourth-generation L405 announced later that year. This collection covers parts for all L322 model years from 2002 to 2012.
The L322 used different engines depending on the production era. Pre-facelift models (2002 to 2005) used the BMW M62 4.4-litre V8 petrol or the BMW M57 3.0-litre Td6 diesel. Facelift models (2006 to 2009) used Jaguar-sourced engines: the AJ41 4.4 V8 or AJ34S 4.2 supercharged V8 for petrol, and the AJD-V8 3.6 TDV8 diesel from model year 2007. Late production (2010 to 2012) used the AJ133 5.0 V8 or 5.0 supercharged V8 for petrol, and the 4.4-litre AJD-V8 TDV8 diesel. Your VIN and the engine code on the engine plate confirm your exact specification. Some 2006 registrations carry the outgoing BMW M62 engine, so confirming via VIN rather than registration year is recommended.
Yes, significantly. The engine change between the pre-facelift and facelift L322 means that engine ancillaries, cooling components, fuel system parts, and transmission service components are not interchangeable between eras. The transmission also changed: early models used a five-speed GM or ZF automatic, while facelift models used the ZF 6HP six-speed, and late production 4.4 TDV8 models used the ZF 8HP eight-speed. Always confirm your engine code and transmission type before ordering engine-specific or gearbox-specific components.
Yes. Four-wheel independent air suspension was standard on the L322 from model year 2002 through to 2012. This applies to all variants and all engines across the full production run. Air suspension compressors, valve blocks, air struts, height sensors, and relay units are all available in this collection for the full 2002 to 2012 range.
Yes. The pre-facelift L322 with the BMW M62 4.4 V8 petrol and BMW M57 3.0 Td6 diesel remains well supported in the EU aftermarket. Service parts including filters, gaskets, cooling components, brake parts, and air suspension components are available across all three quality tiers. BMW-specific items such as the M62 valley pan gasket, M57 turbo actuator, and 5HP transmission service kit are stocked. The earliest L322 vehicles are now over 22 years old, so chassis-related items, body fasteners, and electrical connectors should be inspected as part of any major service. If you are ordering for a known fault and cannot find the part on this page, contact the Budget Parts team with your VIN.
Both engines are members of the Jaguar Land Rover AJD-V8 diesel family but they are not interchangeable. The 3.6 TDV8 was fitted from model year 2007 through to model year 2009 and produces 268 hp in L322 specification, paired with the ZF 6HP six-speed automatic. The 4.4 TDV8 was introduced for model year 2010, produces 309 hp, and is paired with the ZF 8HP eight-speed automatic. Engine block, cylinder head, turbocharger configuration, fuel injection system, exhaust after-treatment, oil sump capacity, and transmission interface all differ. Service parts including timing components, oil filters, fuel filters, and EGR coolers are specific to each variant. Confirm via VIN before ordering any TDV8-specific component.
For most parts, yes. The L322 VIN encodes model year (position 10), engine code, transmission, and key specification flags. Because the L322 went through two powertrain transitions (2005-2006 BMW to Jaguar petrol, 2007 Td6 to 3.6 TDV8 diesel, 2010 to 4.4 TDV8 + AJ133 V8), VIN-based confirmation is more reliable than registration year for any engine, transmission, or fuel-system part. The Budget Parts team can decode your VIN and verify the correct part before despatch if you contact us with your VIN and the part you need.
The L322 is the third-generation Range Rover, produced from 2002 to 2012. The L405 is the fourth generation, produced from 2013 to 2022. The two share no platform architecture. The L405 was the first Range Rover built on an all-aluminium monocoque structure and uses Jaguar Land Rover Ingenium and AJD engine families. Parts for the L322 and L405 are not interchangeable. If you own a 2013 or later full-size Range Rover, you need the L405 collection.