Range Rover L322 Parts

Brake Disc Retaining Screw that locates the brake disc against the wheel hub flange, holding the disc square and in position while the caliper and ...

Water Outlet Tube for the engine cooling circuit of the naturally aspirated 5.0L AJ133 V8 petrol engine. The tube carries coolant between the wate...

Oil Separator Reservoir forms part of the crankcase emission control (crankcase ventilation) system. It separates entrained engine oil from crankc...

Retaining Clip is a fastening clip used in the radiator grille and front bumper assembly. It secures the grille and front bumper trim components t...

Clip - retaining clip for the radiator grille and front bumper assembly. It secures the grille and bumper components to their mountings.

Overflow Container Cap for the cooling system expansion (overflow) reservoir. The cap seals the coolant expansion tank and maintains system pressu...

Head Gasket for the right-hand cylinder bank of the 4.4L DOHC V8 turbo diesel (TDV8) engine. Seals the joint between the right-hand cylinder head ...

Cylinder Head Gasket for the left-hand cylinder head of the 4.4L DOHC DITC V8 diesel (TDV8) engine. Seals the joint between the left-hand cylinder...

Head Gasket for the right-hand cylinder bank of the 4.4L DOHC V8 turbo diesel (TDV8) engine. Seals the joint between the right-hand cylinder head ...

Cylinder Head Gasket for the left-hand cylinder head of the 4.4L DOHC DITC V8 diesel (TDV8) engine. Seals the joint between the left-hand cylinder...

Final Drive Lubricant - a fully synthetic 75W-90 gear oil meeting API GL5, supplied in a 4 litre pack. Specified for the front and rear final driv...

Brake Caliper Guide Pin Dust Cover for the front and rear brake calipers. The boot fits over the caliper guide pin and seals against the carrier b...

Brake Pad Fitting Kit - Front - caliper hardware set used when renewing the front brake pads, covering the guide bush and seal components that loca...

Parking Sensor for the park distance control (PDC) system, used in both front and rear bumper positions. The sensor mounts into its aperture in th...

Camshaft Position Sensor mounted in the timing gear cover, reading the toothed target on the camshaft drive to give the engine control module a dir...

Spark Plug Aperture Gasket seals the spark plug aperture in the cylinder head cover on the left hand cylinder bank. It closes the joint between th...

Camshaft Position Sensor mounted in the timing gear cover, reading the toothed target on the camshaft drive to give the engine control module a dir...

Thermostat Housing for the 5.0-litre AJ133 V8 petrol engine, part of the engine cooling circuit. The housing seats the coolant thermostat and form...

Thermostat Housing for the 5.0-litre AJ133 V8 petrol engine, part of the engine cooling circuit. The housing seats the coolant thermostat and form...

Cylinder Head Gasket seals the joint between the cylinder head and the engine block on the 3.0L V6 turbo diesel engine, containing combustion press...

Cylinder Head Gasket seals the joint between the cylinder head and the engine block on the 3.0L V6 turbo diesel engine, containing combustion press...

Keyless Entry and Start Aerial is the receiver antenna for the passive keyless entry and push-button start system, part of the vehicle's anti-theft...

Remote Control Receiver is part of the vehicle anti-theft alarm system, operating on the 433MHz radio frequency band. It receives the coded radio ...

Inlet Manifold Gasket for the left-hand cylinder bank, sealing the inlet manifold to the cylinder head. Seals the joint between the inlet manifold...

Chain - Timing

Turbocharger Circlip - retaining clip for the turbocharger actuator on diesel turbocharger installations. It secures the actuator rod to the contr...

O-Ring seals the variable valve timing (VVT) solenoid within the timing gear and sprocket assembly. It maintains an oil-tight joint between the VV...

Inlet Manifold Gasket - 5.0 V8 - RH seals the inlet manifold to the cylinder head on the right-hand bank of the 5.0 litre V8 petrol (AJ133) engine,...

Gasket - Oil Filter to Block seals the joint between the oil filter housing and the cylinder block, within the Oil Cooler and Filter assembly. It ...

Spark Plug Aperture Gasket for the right-hand camshaft cover, sealing the spark plug well against oil ingress. The camshaft cover carries a tube f...

Idler Pulley for the front-end accessory drive of the 4.4L V8 diesel engine. The idler pulley provides a smooth rolling surface that routes and gu...

O-Ring for the oil pump inlet tube, part of the oil pump, sump and filter assembly. It seals the joint at the oil pump inlet (pick-up) tube, keepi...

Cylinder Head Gasket seals the joint between the cylinder head and the engine block on the 3.0L V6 turbo diesel engine, containing combustion press...

Gasket - Oil Filter to Block seals the joint between the oil filter housing and the cylinder block, within the Oil Cooler and Filter assembly. It ...

Secondary Drive Belt from the front end accessory drive, 1444 mm in length and eight-ribbed. It runs from the crankshaft pulley over the tensioner...

Inlet Manifold Gasket - 5.0 V8 - RH seals the inlet manifold to the cylinder head on the right-hand bank of the 5.0 litre V8 petrol (AJ133) engine,...

Breather Tube - crankcase ventilation tube within the engine's emission control system. It routes crankcase gases from the engine back into the in...

Cam Cover Gasket for the right-hand cylinder head of the 5.0L AJ133 V8 petrol engine, part of the camshaft cover assembly. The gasket seals the jo...

Inlet Valve - cylinder head inlet (induction) valve for the 5.0L V8 AJ133 supercharged petrol engine. The inlet valve admits the intake charge int...

Timing Tensioner Screw - M8 x 45mm is the fastener that secures the chain tensioner within the timing gear assembly of the 5.0 litre V8 petrol (AJ1...

Gasket - Oil Cooler seals the engine oil cooler to its mounting face, within the Oil Cooler and Filter assembly. It maintains the integrity of the...

O-Ring for the oil pump outlet tube, sealing the pressurised feed within the oil pump, sump and filter assembly. The outlet tube carries oil from ...

Timing Gear Bolt from the engine timing drive, securing the camshaft sprocket and variable camshaft timing adjuster to the camshaft. It provides t...

Screw, M6 x 38mm, from the timing gear assembly - timing chains, tensioners and guides, and the auxiliary drive. It retains the chain guide in pos...

Water Manifold Gasket for the engine cooling and heater circuit - it seals the water manifold tube where it leaves the cylinder block and feeds the...