Range Rover L322 Parts

Crankcase Breather Tube - a hose in the crankcase emission control (crankcase ventilation) system on petrol engines. The tube routes blow-by gases...

Pin, 6 x 36mm, from the timing gear and auxiliary drive assembly of the 5.0L AJ133 V8 petrol engine. It serves as the guide pin for the auxiliary ...

Piston Ring Set for the 4.4 TDV8 diesel engine, supplying the rings for one piston at standard bore size. The set provides the compression and oil...

Crankshaft Front Oil Seal for the timing gear cover, sealing the crankshaft nose where it passes out through the front cover. It runs on the crank...

D3S xenon headlamp bulb, supplied with its igniter, for headlamp units originally built as bi-xenon or adaptive xenon assemblies. D3S is a mercury...

Front Brake Caliper Attachment Kit supplying the pad-retaining and caliper attachment hardware that secures the brake pads in the front caliper bod...

Pulley - Fan

Blind Anchor Nut - a threaded anchor nut that provides a captive fixing point where the reverse side of the panel is inaccessible. It is used in t...

Front Brake Pad Set - friction pads for the front disc brake calipers, forming part of the front foundation braking assembly. The pads are carried...

Piston ring set for the 5.0L AJ133 V8 petrol engine, in both naturally aspirated and supercharged form. Part of the cylinder block assembly – cran...

Exhaust Gas Temperature Sensor for the front position of the exhaust after-treatment system on 4.4L V8 turbo diesel engines fitted with a Diesel Pa...

Intercooler to Inlet Manifold Gasket from the charge air induction system of the supercharged 5.0L V8 petrol engine (AJ133). The supercharger and ...

Wheel Nut Set - set of twenty wheel nuts, sufficient for four five-stud road wheels. Each nut clamps the road wheel against the hub face on the wh...

Flanged Hex Bolt M10 x 25mm - a threaded fastener used in the engine timing gear and turbocharger mounting assemblies. The integral flange under t...

Gear - Transfer Case Actuator is a replacement drive gear for the transfer case shift actuator motor. The actuator motor drives high and low range...

Mass Air Flow Sensor is fitted in the air cleaner assembly of the 4.4L DOHC V8 diesel engine, downstream of the air filter. It measures the mass o...

Exhaust Gas Temperature Sensor for the 4.4L V8 turbo diesel (SDV8/TDV8) exhaust and after-treatment system. The sensor measures gas temperature in...

Gasket - Cylinder Head

Rear Crankshaft Seal and Retainer - the rear main oil seal supplied complete with its retainer housing, sealing the crankcase at the transmission e...

Cylinder Head Gasket for the 4.4L V8 diesel engine, right-hand cylinder head. It seals the joint between the cylinder head and the engine block, co...

Exterior mirror motor - left-hand side glass adjustment motor within the door mirror head. The motor sits behind the mirror glass and drives the g...

Manifold Absolute Pressure (MAP) Sensor - measures the pressure inside the intake manifold and supplies an engine-load signal to the engine control...

Crankshaft Seal & Retainer – Rear is the rear main oil seal together with its carrier plate, mounted to the rear face of the cylinder block on ...

Oil Pump for the engine lubrication system. It draws oil from the sump and pressurises it through the lubrication circuit to the engine's bearings ...

Leak Detection Pump - DMTL (Diagnostic Module Tank Leakage) unit for the fuel tank evaporative emission (EVAP) system. The module sits between the...

Output Flange for the transfer box output shaft. It bolts to the output shaft and provides the mounting face for the propshaft, transmitting drive ...

Oil Cooler Assembly for the 5.0-litre supercharged V8 petrol engine (AJ133). It forms part of the engine lubrication circuit, transferring heat fro...

Oil Seal for the ZF transfer case. Seals a rotating shaft on the transfer case to retain lubricant and exclude contaminants.

Drain Plug Washer for the transfer box drain and level plugs. The washer seals the plug against the transfer box casing and is replaced each time ...

Cylinder Block Core Plug Seal sealing a core plug aperture in the cylinder block. It seals a casting core plug opening in the block, preventing co...

Oil Drain Plug for the ZF transfer box housing. The plug closes the drain and fill port in the transfer box casing, and is removed to drain and re...

Wheel Nut Set - Satin Black - set of twenty wheel nuts in a satin black finish, sufficient for four five-stud road wheels. Each nut clamps the roa...

Sensor - High Low Position - Tripminder

Electronic Pressure Control Solenoid for the transfer case control circuit. The solenoid is actuated electrically by the vehicle's control module ...

Brake Pad Front Green

Fuel Pressure Regulator for the right-hand cylinder bank of the 4.4L DOHC V8 turbo diesel (TDV8) engine, supplied with its valve. Regulates pressu...

Sensor exhaust gas oxygen

Oil Cooler Assembly - the oil-to-coolant heat exchanger of the engine's Oil Cooler and Filter assembly. Engine coolant is passed through the coole...

CANNY is an advanced CAN interface developed by Lazer Lamps that enables the seamless installation of auxiliary lights on modern vehicles equipped ...

Sensor - Exhaust Gas - Temperature

Secondary Drive Belt Idler guides and maintains tension on the secondary (supercharger) drive belt within the front-end accessory drive. The idler...