Range Rover Parts

Blanking Plug closes off an unused 8mm (5/16 inch) aperture in a body panel or chassis section. It belongs to the body grommets and panel-sealing g...

Strap

Hex-head bolt, 5/16" UNC thread, 1" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and socke...

Brake Pipe Clip (double) used to route and secure rigid brake pipes within the braking hydraulic system. The double form retains two brake pipes s...

Self-Locking Nut is an M12 x 1.25 nyloc nut used at the shock absorber mountings in the suspension. It retains the lower mounting of the front and...

Thermostat Housing Gasket for the 200TDi 2.5L turbo-diesel engine, sealing the thermostat housing to the cylinder head within the engine cooling ci...

Inline Fuel Filter for petrol fuel-injection (EFI) systems, fitted in the pressurised fuel supply line between the fuel pump and the injector rail....

Starter Motor for the 2.5L 4-cylinder diesel engine, part of the engine electrical starting circuit. When the ignition is operated the solenoid th...

Flywheel Housing Gasket for the 200 TDi diesel engine, sealing the joint between the flywheel (or drive plate) housing and the rear face of the cra...

Bolt 1/4" UNF x 7/8" is a fixing bolt for the track rod and steering damper within the steering linkage. It clamps the track rod end and secures t...

Bolt - Bracket to Chassis is an M10 x 60 mm fastener that secures a bracket to the vehicle chassis frame. It has a 10 mm nominal thread diameter a...

Wheel Centre Cap with a pewter finish, fitting the centre bore of the alloy road wheel. It conceals the hub and the wheel fixings at the centre of ...

Brake Caliper Repair Kit supplying replacement piston seals for overhauling the brake caliper. New piston seals restore the caliper's ability to r...

Screw – a No. 6 × 1/2 in self-tapping screw used to secure interior trim and panel fixings, such as the instrument binnacle, fascia mouldings and a...

Flame Trap fits into the crankcase ventilation circuit of the V8 twin-carburettor petrol engine, between the crankcase breather and the carburettor...

PDWA Valve

Grommet

Differential Pinion Inner Taper Roller Bearing used in the differential pinion shaft assembly within the axle final drive. The bearing supports th...

Rubber Plug Cushion is a moulded rubber blanking plug that fits into a pre-formed aperture in the body, frame or seat base to close off the opening...

Timing Cover Mudshield is the pressed shield that fits over the timing cover at the front of the engine. It screens the timing case and front pull...

Side Repeater Lens is the lens cover for the side repeater indicator lamp. It fits over the repeater lamp bulb to seal the unit and colour the emi...

Fuel Filler Cap that seals the fuel tank filler neck. Non-locking type with a black finish, closing the filler neck against fuel vapour loss and t...

Fir Tree Fastener push-in fixing in light grey, used to retain headlining, roof trim and similar interior and exterior trim panels. The tapered fi...

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

Stud - M10 x 25mm, a threaded fastening stud used across a range of Land Rover assemblies. The stud provides a fixed threaded mounting point, allo...

Handbrake Spring Kit for the transmission brake – the drum-type parking brake mounted at the transfer box output. The kit comprises the shoe reten...

Oil Seal for the input shaft of the ZF automatic gearbox. The seal fits at the front of the gearbox, where the torque converter drives the input s...

Oil seal

Brake Pipe Clip – Double secures a pair of brake pipes along their routing through the braking hydraulic circuit, retaining both lines against the ...

Clutch Release Bush for V8 petrol applications, located within the clutch assembly at the rear of the crankshaft. The bush seats in the spigot rec...

Front Drive Shaft, left-hand, part of the front axle drive assembly. The shaft transmits torque from the front differential to the front wheel hub...

"Land Rover" Rear Decal Badge A self-adhesive lettered name plate forming part of the exterior rear badging, applied to the rear bodywork. The let...

Rear Brake Caliper, right-hand side, for the rear braking circuit on models fitted with solid (non-vented) rear discs. The caliper clamps the brake...

Oil Cooler Thermostat - the thermostatic control valve in the engine oil cooling circuit. It regulates oil flow to the oil cooler in response to o...

Plain Washer - imperial-dimensioned flat washer with an internal diameter of 7/16 inch and an outer diameter of 13/16 inch. Used in general fasten...

Hose pump to box

Aerial with cable Defender

Cable Clip secures wiring harnesses, breather pipes and similar runs to the body, chassis or panel. It locates in an 8mm mounting hole and holds t...

Accelerator Cable in the throttle control linkage, connecting the accelerator pedal to the fuel injection pump. It transmits pedal movement to the...

Track Rod End Assembly for the steering linkage, connecting the track rod to the steering drop arm and transmitting movement from the steering box ...

Static Lap Seat Belt for the second-row seating position, forming part of the interior occupant restraint system. The non-retractable, fixed-lengt...

Headlamp Bezel - black finish. The trim ring that surrounds the 7" round headlamp, retaining the lamp unit in the front panel and finishing the hea...

Water Pump for the 200TDi 2.5L turbo diesel engine, operating in the engine cooling circuit. Belt-driven from the crankshaft, the pump circulates ...

Anti-roll bar bush

Radius Arm Bush mounts at the axle end of the front radius arm, within the front suspension radius arm and axle location assembly. It forms the co...

Upper Link Bush for the rear suspension, fitted within the top link, fulcrum and ball joint assembly. It seats in the upper (top) link to provide ...

Steering UJ upper

Kit latch bonnet catch LHD