Range Rover Parts

Outer Hub Lock Washer for the front and rear hub assembly on Land Rover solid axles. This lock washer secures the hub bearing retaining nut agains...

Propshaft Gaiter with Clips for the front propshaft sliding joint. This rubber gaiter fits over the splined sliding joint (slip yoke) of the front...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Hub Nut Spanner for the front hub and wheel bearing assembly. The 52mm tool engages the hub retaining nut on the front stub axle. Designed for use...

Drain Plug Washer in copper, used to seal axle differential drain plugs against oil leakage. This copper crush washer seats under the drain plug a...

Stop/Tail Light Bulb - 12V 5/21W (trade reference 380) for rear lamp assemblies. This dual-filament bayonet bulb (BAY15d base) provides 5W tail li...

Swivel Housing to Stub Axle Joint Washer for the front axle swivel assembly. This sealing washer fits between the swivel housing and the stub axle...

Universal Joint for the propeller shaft, of the 82mm cap-to-cap type. The universal (cardan) joint connects two sections of the propshaft, transmi...

Differential Pinion Oil Seal for the axle differential housing. This oil seal fits around the pinion flange where the propshaft coupling connects,...

Axle Breather for the front axle housing on vehicles without a remote breather pipe assembly. This screw-in vent allows the air inside the front a...

Differential Pinion Oil Seal for the axle differential housing. This oil seal fits around the pinion flange where the propshaft coupling connects,...

Shock absorber bush (eye), anti roll bar bush

Track Rod End Boot - Polyurethane for the steering track rod end ball joint. This polyurethane boot fits over the track rod end housing, sealing t...

Upgrade your Series Land Rover suspension with this Polyurethane Shock Absorber Bush Set in black. The set includes 4 pieces, providing everything ...

Rubber Sealing Ring for gear selector shafts in the LT76 gearbox and LT95 transfer box. In the LT76 gearbox, two rings are fitted per unit, sealin...

Ignition Condenser for the contact-breaker (points) ignition system, mounted at the distributor. The condenser is a capacitor wired across the con...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Differential Carrier Gasket for the Rover-type axle assembly. The gasket seals the differential carrier housing against the axle casing at the cen...

Axle Key Washer for the hub nut locking system in the axle assembly. This tab washer seats beneath the axle hub nut, with tabs that locate into ma...

Anti-Roll Bar Washer used at the anti-roll bar and shock absorber mounting. The washer spreads the clamping load of the retaining nut across the m...

Detent Spring for the manual gearbox gear selector mechanism. The spring loads the detent ball against the selector shaft, holding the selected ge...

Side Cover Gasket sealing the cylinder-block side cover (tappet inspection cover) to the block face, for petrol and diesel engines. The side cover...

Copper Sealing Washer used across a wide range of sealing applications on Land Rover vehicles. This soft copper washer provides a reliable, leak-f...

7" round LED headlamp 12/24V black 78W LHD (pair)

Cable Clip for securing the body wiring harness, part of the vehicle electrical system. This clip retains a cable run against the body or chassis,...

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

Wheel Spanner with a 27 mm socket, a hand tool for removing and refitting wheel nuts. Engages the 27 mm hexagon of the wheel nut to loosen or tigh...

Alternator - charging unit in the vehicle's electrical charging system. Driven from the engine by the accessory belt, it generates current to powe...

Gearbox Plug Sealing Washer for LT76 and LT77 manual gearbox drain, level, and inspection plugs. This sealing washer fits beneath the thread of ge...

Flywheel Housing O-Ring - a sealing ring at the rear of the engine where the flywheel housing meets the cylinder block. Fitted to the 2.25L engine...

Track Rod Clamp is a split-tube collar that secures the threaded track rod end into the track rod tube on the front steering axle. Once the front ...

Track Rod End Boot for the steering track rod end ball joint. This rubber boot fits over the track rod end housing, sealing the ball joint against...

7" round LED headlamp 12/24V chrome 78W LHD (pair)

Condenser for the distributor ignition system. The condenser (capacitor) is wired across the contact breaker points inside the distributor. As the...

Locking plate

Lock Washer secures a threaded fastener against loosening under vibration and thermal cycling. Fitted beneath the nut or bolt head, it bites into ...

Headlight Bulb – H4 – 12V 60/55W is a dual-filament halogen headlamp bulb for headlamp units that take the standard H4 fitting. It carries both the...

Propshaft Bolt Kit - Rear is a driveline fixing set for securing the rear propeller shaft at its flange connections. The kit provides the correct-...

Spring plate

Bolt, a hexagon-head fastener with a 5/16" UNF thread, 7/8" long. This imperial fastener is of the UNF (Unified National Fine) thread series and i...

Ball Bearing for the transfer box, supporting the output shaft and its output flange. Fitted in the LT230 and NV225 transfer boxes, the bearing lo...

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

Bulb rated 12V 4W with a small-diameter fitting, part of the vehicle lighting system. This low-wattage bulb suits the small-fitting (Lucas-type) l...

Castle Nut (castellated nut) used to retain halfshafts, output shafts and differential pinion shafts in Land Rover axle and drivetrain assemblies. ...

Hex-head screw, 5/16" UNF thread, 1-1/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and so...

Lucar Connector - a fully insulated two-way in-line electrical connector for joining wiring within the loom. Of the Lucar (blade) terminal type, i...

Hazard Flasher Relay - the switching relay in the hazard warning circuit. When the hazard switch is operated, the flasher relay pulses all four di...