Range Rover Parts

Bolt 10.9 M12 x 100

Radiator is the main engine cooling radiator with an aluminium core, serving the front of the engine cooling circuit. Mounted ahead of the engine ...

Bolt - an imperial hexagon-head bolt with a 5/16" UNF thread and a 2-3/4" shank length. This is an engine-area fixing for early Series application...

Joint Washer - a sealing washer for the piston-cooling oil squirt jet in the engine lubrication circuit. It seals the oil spray jet where it meets...

Windscreen Washer Non-Return Valve fits inline in the washer fluid delivery pipe, forming part of the windscreen washer system. It allows fluid to...

Exhaust Clamp Plate for the exhaust system, used at the front-pipe and catalyst joint. The plate works together with a U-bolt to draw the exhaust c...

Ignition Coil for the V8 petrol ignition system. It converts the low-voltage supply into the high-tension voltage that fires the spark plugs throug...

Single Pipe Clip, a routing clip that retains a single pipe or line against the chassis or body. It holds fuel, evaporative-loss or brake pipework...

Single Clip is a single-aperture retaining clip used to secure brake and fuel pipes, the accelerator cable and the hand throttle control. It holds...

Anti-Rattle Spring for the front disc-brake caliper. It holds the brake pads under light tension inside the caliper, taking up free play so the pad...

Core Plug for the rear of the camshaft bore in the V8 petrol cylinder block. The cup-type plug seals the machined opening at the rear of the camsh...

Bulb, 12V 4W (type 233, BA9s single-contact bayonet cap). A miniature bayonet bulb used in number plate, side, interior and rear lamp positions.

Spring Retention Ring for the front coil-spring suspension. It clamps the upper end of the road spring, securing it against its seat on the chassis...

O-Ring for the speedometer drive spindle on the LT230 transfer gearbox. Seals the spindle housing where the speedometer drive take-off enters the ...

Fuel Pipe Olive for the fuel supply line. The olive is the compression ferrule that seats between the fuel pipe and its union fitting. When the un...

Cable Grommet for the wiring loom, fitting a 41.5 mm panel hole and accepting a cable of up to 6 mm. Made of black rubber, it lines the hole where...

Double-Grooved Ball Bearing for the manual gearbox and transfer box. It supports and locates a rotating shaft within the casing, carrying the radia...

Starter Motor for the 3.5L V8 petrol engine, operating in the engine starting circuit. When energised through the starter solenoid, the pinion is ...

Sump Plug for the engine oil sump (oil pan), part of the engine lubrication system. It threads into the drain hole at the base of the sump to seal...

Flange Bolt - M8 x 85mm hex bolt with an integrated flange beneath the head. The flange spreads the clamping load across a wider bearing surface a...

Propshaft UJ Circlip - a retaining clip for the universal joint of the propeller shaft. It seats in the groove of the yoke ear and holds the beari...

Exhaust Mount Washer from the exhaust mounting hardware. It seats beneath the fastener at an exhaust mounting point, spreading the clamp load acros...

Handbrake Adjuster Repair Kit for the cable-operated transmission drum handbrake. The kit renews the adjuster mechanism of the drum brake mounted ...

Level plug R380

Cylinder Head Gasket for the Rover V8 petrol engine, sealing the joint between one cylinder head and the engine block. It seals the combustion cha...

Cylinder Head Bolt (Long) for the V8 petrol engine, securing the cylinder head to the engine block. This is the longer of the two head bolt length...

Cylinder Head Bolt (Short) for the V8 petrol engine, securing the cylinder head to the engine block. This is the shorter of the two head bolt leng...

Inlet & Exhaust Manifold Gasket - 300TDi

Alternator for the engine charging circuit, of the Lucas A127 type rated at 45A output. Driven by the auxiliary drive belt from the crankshaft pul...

Fuel Pressure Regulator mounts on the fuel rail of the multiport electronic fuel injection (EFI) system. It holds a constant pressure difference b...

Hex-head bolt, 7/16" UNF thread, 1-1/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and soc...

Steering Wheel - a 14-inch three-spoke replacement wheel with a black vinyl rim and black centre. The wheel mounts to the steering column through ...

Coolant Temperature Transmitter is the engine coolant temperature sender, threaded into the cylinder head where it reads the temperature of the coo...

Countersunk Screw - a machine screw with a flat, cone-shaped head that seats flush with the surface it fixes, leaving no proud edge. Metric M6 thr...

Exhaust mounting spacer tube

Bonnet Alarm Switch

Water Temperature Sensor (coolant temperature transducer) that threads into the thermostat housing within the engine cooling circuit. The transduc...

Window Regulator Handle for the front door, operating the manual window regulator (winder mechanism) to raise and lower the door glass. The handle...

Oil Pressure Sensor Monitors engine oil pressure in the lubrication circuit and signals the oil pressure gauge or warning lamp on the instrument pa...

Banjo Bolt (6mm) for the fuel injector leak-off return circuit on the 200TDi and 300TDi 2.5L turbo diesel engines. The hollow bolt clamps the inje...

Decoke Gasket Set for the 3.5L V8 petrol engine with twin carburettors. The set supplies the gaskets needed when the cylinder heads are removed fo...

Mainshaft Bearing supports the mainshaft within the LT230 transfer box, carrying the shaft's rotational loads and keeping it running true as drive ...

Decal - ZF Automatic Gearbox is an adhesive identification label associated with the ZF automatic transmission, located in the centre console and c...

Headlamp Bezel - stainless steel, 7". The trim ring that surrounds the 7" round headlamp, retaining the lamp unit in the front panel and finishing ...

Polyurethane Boot - Defender - Discovery 1/2 - RRC - P38

Steering box sector shaft seal kit for the steering system. This kit contains the sealing components required for the sector shaft assembly withi...

Front Stub Axle for the front hub and swivel pin housing assembly at the front axle. The stub axle passes through the swivel pin housing and provi...

Gasket kit 300tdi lower block set no rear crankshaft seal