Range Rover Parts

Push Rod - a valvetrain component in the overhead-valve layout of the Rover V8 engine. It sits between the camshaft-driven tappet and the rocker a...

Modular Steel Wheel - Black - 7J x 16 A modular steel road wheel finished in black, sized 7J x 16 with an ET08 offset. The steel construction suit...

Bracket

Propshaft Spacer Kit (25mm) - a driveline spacer fitted between the propshaft flange and the transfer box or differential flange to restore the pro...

Screw is a fastener used in cooling and heating system assemblies on Land Rover vehicles.

M12 Nut used as a fastener at several chassis and running-gear locations, including the swivel pin housing, drive shaft fixings and front brake cal...

Bolt 5/16" UNC x 5" is a long mounting bolt for the coolant pump and power steering pump on the 3.5L V8 petrol engine. Its length carries the powe...

Changeover Relay - 5-Pin - Green is a standard 5-pin changeover relay used across multiple electrical circuits. This relay is used in various appl...

Inertia Switch in the fuel supply and engine electrical circuit. It cuts electrical power to the fuel pump on a sudden impact or severe deceleratio...

Spring Washer for use as a locking fastener component across Land Rover assemblies. A helical split spring washer providing resistance against fas...

Shock Dropper - Rear - Pair: zinc-plated steel relocated rear shock absorber top mounts that lower the upper mounting point by 50mm. By relocating...

Rear Shock Absorber provides damping control within the rear axle spring and damper assembly for suspension set up with extended travel. Twin-tube...

Front suspension shock absorber designed to control spring oscillation and maintain tyre contact with the road surface. Twin-tube low-pressure ni...

CV Joint Circlip - the retaining circlip that secures the constant velocity (CV) joint to the front drive shaft. The circlip locates in a groove o...

Water Pump for the 3.5L Rover V8 petrol engine cooling circuit. Belt-driven from the front of the engine, the pump circulates coolant through the ...

Kickdown Cable Assembly for the automatic transmission control. The cable links the throttle to the automatic gearbox, relaying throttle position s...

Power steering seal kit

Steering Lever - RHD for the Adwest power steering box, supplied with the ball joint fitted. Also known as the drop arm, the lever clamps onto the...

Locknut is a self-locking M10 nut used as a general threaded fastener across the vehicle. Its locking feature resists loosening under vibration, m...

Nut - M8 plain low-profile nut, sold individually. A standard metric M8 nut in the low-profile (thin) form. Used across gearbox, suspension, axle,...

Fuel Tank Bracket for securing the fuel tank to the vehicle chassis. This metal bracket forms part of the fuel tank mounting assembly, locating an...

Radius Arm Bush Set - Front - Polyurethane is a set of four polyurethane bushes for the front radius arm-to-chassis mountings. The radius arms loc...

Spill Rail for the 300 TDi fuel injection system. The spill rail links the leak-off unions at the top of the injectors and carries surplus fuel fro...

Fulcrum Bracket for the rear suspension A-frame assembly. The bracket provides the chassis mounting point for the A-frame ball joint, which locate...

Alloy Wheel is a single-piece 16 x 7-inch alloy road wheel finished in black. It has a five-stud 5x165 mm bolt pattern and an ET20 offset, which s...

Window Regulator Escutcheon - Front Door

Nut - 10/32" UNF A nut with a #10-32 UNF (Unified National Fine) internal thread, run onto a matching UNF bolt or stud to clamp the joint.

Swivel Pin Housing Oil Seal for the front axle swivel and stub axle assembly. This is the outer seal, fitted at the interface between the stub axle...

Brake Disc - Solid - Front is the front brake disc, mounting to the wheel hub and providing the friction surface the brake pads clamp against durin...

Half Shaft Shim - 0.90mm is a 0.90mm selective shim that fits on the outside of the axle driving member to set the endfloat of the half shaft withi...

Half Shaft Shim - 0.60mm is a 0.60mm selective shim used to set the endfloat of the axle half shaft within the hub assembly. It is fitted at the d...

Front Axle Shim, 0.45mm thick. Fitted to the front axle half-shaft assembly to set the correct end-float, taking up clearance so the shaft is posit...

O-Ring - LT95 Gearbox seals the transfer shaft on the LT95 4-speed gearbox, which carries an integral transfer case, preventing oil leakage at the ...

Wheel Hub Stud FRC5926 or RUF000020 for Defender 90 And 110, Discovery I and Range Rover Classic.

O-ring

Gear Selector Ball End is the ball-joint pivot in the gear change selector linkage, connecting the selector rod to the transmission operating shaft...

Gearbox Gasket seals the top cover to the main casing of the LT77 five-speed manual gearbox, forming an oil-tight joint between the top cover plate...

Flange Bolt, M8 x 120 mm - a hexagon-head flange bolt that secures the coolant (water) pump on the 300TDi 2.5-litre turbo diesel engine. The integ...

Camshaft Oil Seal seals the camshaft on the 2.5L 4-cylinder diesel engines, including the 200TDi. Fitted at the front of the engine where the cams...

Sealing Washer is a copper crush washer used to seal banjo and threaded union joints in the fuel system. Fitted at unions such as the injection pu...

Crankshaft Woodruff Key for the 2.5L 300TDi and 2.5L Td5 diesel engines. This semicircular key seats in a slot machined into the crankshaft nose an...

Timing Gear Housing Gasket for the 300 TDi engine, sealing the drain plate to the timing gear housing at the front of the engine. Forms the joint ...

Banjo Bolt for the fuel and oil circuits, used to secure a banjo union to its housing while allowing fluid to pass through the cross-drilled body. ...

Valve Stem Seal - the seal fitted over the valve stem in the cylinder head to control the oil that passes down the stem into the port. This is the...

Breather Filter is the crankcase ventilation filter mounted at the rocker cover on the V8 EFI petrol engine. It filters oil vapour and mist from t...

Spring Retaining Plate Front coil spring retaining plate that clamps over the top of the spring at its seat, holding the spring captive so it canno...

Plain Washer M8

Power Steering Pump - Hobourn-type hydraulic pump serving the power-assisted steering circuit on V8 engines. It is driven from the crankshaft by a ...