Range Rover Parts

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Dislocation Cone - Rear Coil Spring for the rear coil spring seat assembly. When long-travel shock absorbers or lowered top-mount shock relocators...

Dowel - Bell Housing Alignment in the gearbox/engine interface assembly. This dowel locates the bell housing accurately relative to the engine blo...

Crankshaft Bolt is the retaining bolt that secures the pulley and damper assembly to the nose of the crankshaft on the V8 petrol engine. Threaded ...

Blanking Plug - a push-fit plug used to close an unused aperture in a body panel, door or interior trim component. It seals the opening against wa...

Grommet - rubber sealing grommet, 3/4 inch overall diameter with 1/8 inch centre hole. Used to seal and protect wiring cables where they pass thro...

Coil Spring - Front - +2" Light Duty is a front suspension coil spring providing approximately 50mm (2 inches) of lift above the standard ride heig...

Shock Absorber Bush Kit for the mounting points of Terrafirma TS-series shock absorbers. The kit provides the hardware required to replace worn bu...

Return to Centre Steering Damper for installation within the steering linkage assembly. This unit mounts between the axle steering arms and the st...

Turret Securing Rings - Front are reinforcement rings that fit around the front shock absorber top mount aperture in the inner wing. They distribut...

Flywheel Bolt, 7/16" UNC x 1" hexagonal head, securing the flywheel to the rear crankshaft flange. Used on V8 petrol engines with manual transmiss...

Nut - 2BA, a small-diameter fastener in the British Association (BA) thread standard. 2BA refers to the No.2 size within the British Association t...

Fuel Pump is a low-pressure in-tank unit forming part of the fuel delivery system on petrol applications. Mounted inside the fuel tank, it acts as...

Hex nut

Axle Breather Pipe Clip from the axle breather system, retaining the breather hose along its run from the axle case up to its higher mounting point...

Dump Valve

Blind Nutsert (M6) is a threaded insert that provides an M6 female thread in thin sheet metal or panels where the rear face is not accessible. It ...

Pull Ring for the rear seat lock release. It operates the split rear seat lock mechanism, releasing the seat squab so the backrest can be folded d...

Bolt and Washer - an M8 x 25 mm hexagonal-head bolt supplied with a washer. A general-purpose threaded fastener used at various fixing points on t...

DIFFERENTIAL - ASSEMBLY - FRONT AXLE - 24 SPLINE - 4 BOLT FLANGE - D2

Swivel Housing: - Classic Defender 90/110/127/130 upto KA930455 (upto and including 1993 modelyear) (NON-ABS) Axle Code 20L, 21L, 22L, 23L, - Disco...

Clutch Driven Plate for the V8 clutch assembly. It is carried on the gearbox input shaft between the flywheel and the clutch cover (pressure plate)...

Clevis pin

Half Shaft Shim is a 1.05mm selective shim used in the front axle drive shaft and hub assembly. It sets the endfloat of the front half shaft drive...

Half Shaft Shim - 0.75mm is a 0.75mm selective shim that fits on the outside of the axle driving member to set the endfloat of the half shaft withi...

Transmission Brake Drum for the transmission (hand) brake. Mounts to the transfer box rear output flange and houses the transmission brake shoes, ...

Clutch Release Lever Pivot Cap for the clutch release lever pivot pin. One is required per clutch release arm.

Flange Bolt - M10 x 35mm flanged hex bolt used at a range of driveline and engine mounting points, including bell housing, flywheel and clutch, tra...

Flange Bolt is an M8 x 35 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Cylinder Head Bolt for the 200TDi 2.5-litre direct-injection turbo diesel engine. It secures the cylinder head to the engine block, clamping the he...

Turbo to exh. manifold gasket 200TDi D1, RRcl.

Exhaust Bracket supports and locates a section of the exhaust system against the underbody. It carries the weight of the exhaust at its mounting p...

Fuel Injector for the EFI V8 petrol engine, part of the multi-point electronic fuel injection system. The injector is an electrically-operated sol...

Front Cover Gasket for the 2.5L 200TDi diesel engine, the smaller of the front cover gaskets. It seals the joint between the front cover and the c...

Rocker Shaft Clamp for the cylinder head valve train on the 300TDi 2.5L turbo diesel engine. Secures the rocker shaft to the cylinder head pedesta...

Gasket

Intercooler Hose for the 2.5L 300TDi 4-cylinder turbo diesel engine on EGR-equipped variants. This rubber hose connects the intercooler to the int...

Belt Tensioner for the V8 EFI petrol engine, part of the ancillary (serpentine) drive belt system. The tensioner pulley bears against the auxiliar...

Rocker Arm, RH for the rocker shaft assembly of the 2.5L 300Tdi turbo diesel engine. Mounted on the rocker shaft, it transfers push rod motion fro...

Rocker Arm, LH for the rocker shaft assembly of the 2.5L 300Tdi turbo diesel engine. Mounted on the rocker shaft, it transfers push rod motion fro...

Polyvee Belt 3.9V8 1253mm

Oil Drain Pipe Gasket for the turbocharger oil return line on the 300TDi 2.5L turbo diesel engine. It seals the flanged joint where the external o...

Circlip - LT77 Selector Shaft for the LT77 5-speed manual gearbox. This circlip retains the selector shaft within the gear selector and shaft asse...

Hexagon Bolt - an M16 x 100 mm high-tensile bolt, property class 10.9, used to secure the front radius arm. The 10.9 grade provides the high clamp...

Cap bolt

Bolt with a 3/8" UNC (Unified National Coarse) imperial thread and a 2" shank length. A hex-head fastener used in body, chassis and general assemb...

Bolt - M6 x 30mm is a metric threaded fastener with a 6 mm nominal thread diameter and a 30 mm shank length. It secures bolted joints where an M6 ...

Steering Box Oil Seal Oil seal for the input (worm) shaft of the manual, non-power (Gemmer) steering box, sealing around the shaft where it enters ...