Range Rover Parts

Nut is a metric M12 threaded nut used as a general-purpose fastener across multiple vehicle assemblies. It runs onto a matching M12 male thread to...

Crown wheel and pinion set with a 4.1:1 final drive ratio for the rear differential, long nose differential configuration. The crown wheel and pin...

Self-Tapping Screw - a No. 10 x 1/2" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as th...

Protector for the fuel pipe system, fitted within the fuel pipes assembly on petrol applications. Used on Defender with 2.8L 6-cylinder BMW M52 pet...

Suspension Kit - Medium Load - +2" Lift is a matched front and rear spring and damper set supplied as a single package, pairing +2" (50 mm) lifted ...

Shaft 90/110 RH 31/10

Throttle Linkage for the 3.5L V8 fitted with twin Stromberg 175CD carburettors. This linkage connects the throttle pedal input to both Stromberg c...

Bolt - M6 x 55mm hex head bolt used in braking system assemblies. Standard metric hex fastener supplying clamping force in brake-related mounting ...

Exhaust Manifold - LH End Section for the 300TDi 2.5L inline 4-cylinder turbo diesel engine. Forms the left-hand (longer elbow) section of the two...

Spring Nut A clip-on spring-steel fastener, also known as a speed nut, used across body, grille and chassis fittings. It slides over a panel edge ...

Inline Fuel Filter for petrol engines, fitted in the low-pressure fuel supply line between the tank and the fuel pump or carburettor. This sealed ...

Wiper Motor Mounting Pad for the rear wiper motor, used on the Defender and Range Rover Classic. This rubber fixing pad sits between the wiper mot...

Layshaft Shim for the LT77 five-speed manual gearbox, located at the layshaft (countershaft) front cover and bearing. This is a selective shim use...

Diesel Fuel Filter Plug Seal - a sealing ring for the drain plug on the diesel fuel filter and sedimentor. It seals the drain/bleed plug against t...

Breather Hose for the 300 TDi crankcase ventilation system. The hose carries crankcase breather (blow-by) gases from the engine breather outlet ba...

Oil Pump Driveshaft

Battery Isolator Switch - key-operated master cut-off switch for the vehicle electrical system, rated at 300A. Wired inline on the main battery le...

Pack Gasket - Zenith/Stromberg 175CD (Small) is a gasket pack for the Zenith/Stromberg 175CD constant-depression carburettor. It supplies the gask...

Panhard Rod Bush for the front suspension lateral location assembly. This rubber bush is pressed into the Panhard rod eye and provides the complia...

Engine Oil Dipstick for the 300TDi 2.5L turbo diesel engine. Locates in the dipstick tube on the engine block and provides the oil level reference...

Voltage Sensitive Switch - a 45-amp voltage-sensitive relay used in the vehicle's auxiliary charging and accessory circuits. The switch monitors s...

Power steering box assembly used within the hydraulic steering system, converting rotary input from the steering column into lateral movement of th...

Plain Washer - 7/16" used in the power steering box assembly. This flat washer is used within the steering hydraulic assembly at the power steerin...

Hexagonal Plug for the swivel pin housing oil level and drain. This hex-head plug is used in the front axle swivel pin housing as both an oil leve...

Front Output Shaft for the LT230 transfer box. It carries drive from the transfer box to the front propeller shaft. The shaft runs in the front ou...

Gearchange Spring for the LT77 five-speed manual gearbox, fitted within the gearchange and lever assembly. The spring acts on the gear lever mecha...

Bracket

Clutch Release Arm Pivot Plate for the LT77 5-speed manual gearbox. Mounts inside the clutch bellhousing and provides the pivot point for the clut...

Upper Radiator Mounting Bracket that locates and secures the top of the radiator in the cooling system. Fitted to four-cylinder TDi and Td5 applic...

Oil Jet for cylinders No.2 and No.4, fitted in the cylinder block of the 2.5L Diesel NA, 2.5L Turbo Diesel, 200TDi and 300TDi engines. This piston...

Hose

Blanking Plug

Needle Roller Bearing - 3rd Gear Mainshaft is installed within the LT77 5-speed manual gearbox mainshaft gear assembly, supporting the 3rd gear on ...

Baulk Ring for the LT77 5-speed manual gearbox synchromesh assembly. The baulk ring is the friction cone element of the synchromesh unit. It conta...

Rocker Shaft Spring for the 2.5L 300TDi 4-cylinder turbo diesel engine. This spring locates and tensions the rocker shaft assembly within the cyli...

Transfer Box Cover Gasket seals the joint between the transfer box cover and the transfer case. It forms an oil-tight seal across the cover-to-cas...

Camshaft Pulley O-Ring - the seal fitted at the camshaft pulley on the front timing drive. It seals the joint between the camshaft nose and its dr...

Cylinder Head Gasket for the 2.5L 200TDi and 300TDi diesel engines, supplied in the 1.4mm compressed-thickness grade (identified by two holes). Th...

O-Ring seals the intermediate shaft in the LT230 transfer box, sitting between the shaft mounting and the transfer casing to hold the oil seal at t...

Front Cover to Gearcase Gasket seals the joint between the front cover and the main gearcase on the LT77 5-speed manual gearbox. This gasket preve...

O-Ring - Diff Lock Selector Shaft - LT230 Transfer Case This O-ring seals the differential lock selector shaft where it passes into the LT230 tran...

Thrust Washer for the differential assembly within the LT230 transfer box. This 1.35mm thrust washer sits within the LT230 centre differential, co...

Camshaft Bolt for the Rover V8 engine, securing the camshaft sprocket to the front of the camshaft. This M12 x 30 mm bolt retains the camshaft dri...

Inlet Valve for the cylinder head valvetrain of the 200TDi 2.5L 4-cylinder turbo diesel engine. The valve seals against its seat in the cylinder h...

Door Latch Bell Crank is a pivoting lever within the side door latch assembly that transfers actuation from the handle linkage to the latch. Mount...

Synchro Shift Plate - a shifting plate (shift key) within the synchroniser assembly of the five-speed manual gearbox. It locates in the synchronis...

Blanking Plug is a rubber grommet used to seal unused 1-inch (25.4 mm) diameter holes in body panels, bulkheads and floor sections. The plug press...