Range Rover Parts

Radius Arm - front axle locating link in the coil-sprung front suspension. The radius arm ties the front axle to the chassis, controlling fore-and-...

Engine Mounting Rubber (V8) supports the V8 petrol engine on the chassis and isolates its vibration from the bodyshell. The bonded rubber-to-metal...

Camshaft for the Rover V8 EFI petrol engine (3.9L, 4.0L and 4.6L variants). Mounted centrally in the cylinder block, the camshaft is driven from t...

Braided Earth Strip is a flexible braided conductor that forms an electrical earth (ground) bond between two points in the vehicle. It provides a ...

Brake Caliper Repair Kit supplying replacement piston seals for overhauling the brake caliper. New piston seals restore the caliper's ability to r...

Second Speed Gear for the LT77 five-speed manual gearbox. It runs on the mainshaft within the first, second and fifth-speed gear group and meshes w...

Bearing for 2ND Gear Suffix H Onwards and 3RD Gear On - Freelander 1

Synchromesh Assembly First/second gear synchromesh assembly for the LT95 four-speed gearbox. Synchronises shaft and gear speeds during 1st-to-2nd ...

Lazer ST4 Evolution LED Spotlight - a compact four-LED auxiliary driving lamp producing a controlled long-range beam for forward illumination. The...

Coating Spray Gun, bottle-mount type, for applying protective coating. This Schutz-style gun screws directly onto the 750ml coating bottle, so no s...

Rear suspension bush kit covering the trailing arm and A-frame mounting points of the rear coil-sprung suspension. The trailing arms locate the re...

Rear Shock Absorber Mounting Brackets for the rear suspension damper installation, supplied as a pair. These brackets weld to the rear axle housin...

Small-End Connecting Rod Bush for the 2.5L 200 TDi diesel engine. The small-end bush is pressed into the little end of the connecting rod and carr...

Front Axle Panhard Rod Bush - Late Type, for replacement at the Panhard rod mounting point on the front axle assembly. The bush provides the compl...

Primary Pinion Shim sets the installed position of the primary pinion within the LT95 four-speed gearbox (V8) casing. 2.10 mm thick, it controls p...

Serrated Washer, 7/16", used within the clutch master cylinder and pipe assembly. The serrated face bites into the mating surface as the fixing is...

GENUINE LR camshaft sprocket for Rover V8 engines

4-Pin Differential for the Land Rover-type axle. The differential takes drive from the propshaft through the crown wheel and pinion and splits it ...

Breather Hose is part of the crankcase ventilation system on the 3.5L V8 twin-carburettor petrol engine. It routes breather gases through the vent...

Engine Mount - Right Hand supports the engine at the right-hand mounting point and isolates engine vibration from the chassis. It locates between ...

Ignition Wiring Harness - the low-tension (LT) link lead within the V8 petrol ignition system. This harness carries the low-tension (primary) side...

rear output shaft LT95 4-speed gearbox V8 - S3 109" Stage 1 V8 - 101" Forward Control - Range Rover Classic 4-speed V8 - Early 110" 4-speed V8

Shim 1.65mm for Layshaft Speed - V8 4

Gearbox Crossmember is a detachable structural member that bolts across the chassis side rails beneath the transmission. It carries the rear gearb...

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Differential Guard - a wrap-around steel guard that shields the front or rear differential housing from impact and debris during off-road use. Des...

First Speed Bush for the LT77 five-speed manual gearbox. This selective-fit bush supports the first-speed gear on the mainshaft, within the first, ...

Piston ring set for the 3.5L Rover V8 petrol engine, supplied per piston. The rings seal the combustion chamber against the cylinder bore, transfe...

Cable Connector is a four-way electrical connector body used in the vehicle wiring harnesses. It joins a harness branch to its mating half, retain...

PTO Shaft - Centre - the centre shaft in the power take-off (PTO) drive train. The power take-off transmits rotational drive from the transfer gea...

Wading Kit for the drivetrain and engine breather system, extending the breather points of the axles, gearbox and engine to a higher level. Raisin...

Carburettor Needle for the SU variable-venturi carburettor in the fuel system of the 3.5L V8 petrol engine, in twin-carburettor configuration. The...

Drive Screw for use in Land Rover body, chassis, and hardware assembly. A No.14 × 1" drive screw, supplied individually.

O-Ring for the air conditioning refrigerant circuit, used at the pipe and hose unions through the system including the condenser and evaporator con...

Tensioner Pulley Bearing for the auxiliary drive belt system on air-conditioned vehicles. It is the bearing carried within the idler/tensioner pul...

Intermediate Shaft Circlip Retaining circlip for the intermediate shaft in the LT230 transfer box. Locates on the intermediate shaft to retain the...

Blanking Plate for the inlet manifold of the 3.5L V8 twin-carburettor petrol engine. The plate closes off an unused port on the manifold to maintai...

Hex Bolt - M10 x 40mm is a metric hexagon head bolt used in the hardware and fixings range for Land Rover vehicles. Thread specification M10, leng...

Glow Plug Lead for the pre-heat (glow plug) circuit of the 200 TDi and 300 TDi diesel engines. It interconnects the glow plugs and carries the sup...

Sealing Washer - 18 mm OD x 12 mm ID is a sealing washer with a 12 mm inner diameter and an 18 mm outer diameter, used to seal threaded unions and ...

Shim bearing differential 0.062""

Gasket

Exhaust Clamp a clamp for the exhaust system on 4-cylinder TDi applications. It secures the joint between two exhaust sections, holding the pipes ...

Valve Guide for the cylinder head of the 2.5L 200 TDi and 300 TDi diesel engines. The valve guide is pressed into the cylinder head and locates th...

pipe clip 1/2" (12.7mm) for 3/8" (9.5mm) hole

Grommet - moulded rubber grommet for a panel or component aperture. Fitted into a drilled or pressed hole to line the opening, it provides a seal ...

Screw - an M6 x 20 mm pan-head setscrew with a Torx drive, used as a general multi-application fastener. The Torx socket gives positive tool engag...