Range Rover Parts

Polyurethane Suspension Bush Set in the black compound, for the front and rear coil-sprung suspension. This is a full-vehicle set that replaces the...

Bolt Exhaust manifold fixing bolt, 5/8" UNC x 5-1/2", for the 3.5L V8 petrol engine. Secures the exhaust manifold to the cylinder head within the ...

lead link pump washer 90/110 used to fit newer style washer pumps to earlier vehicles

Bolt securing the exhaust manifold on the Rover V8 petrol engine. A 3/8" UNC x 1 1/8" fastener used to retain the exhaust manifold to the cylinder...

Differential Shim for the crownwheel and pinion assembly. Fitted during differential assembly to set bearing preload and gear alignment. Shim thic...

Differential Shim, 0.074in, used during differential build to set bearing preload and gear alignment. It sits against the differential carrier sid...

Differential Shim - 0.072in, for the Rover-type differential. Fitted during differential setup to set bearing preload and gear alignment. Shim thi...

Crankshaft Thrust Washer - 0.0075in oversize, supplied as a pair. Fitted at the centre main bearing of the four-cylinder engine to control cranksh...

Plain Washer A flat plain washer that spreads the clamping load of a fastener over the mounting surface. Used in body panel and interior fixings.

Drain Plug - a threaded plug that seals a drain point and is removed to drain fluid during service. It is used in several locations depending on ap...

Adjustable Panhard Rod - lateral axle locating link within the suspension assembly. The Panhard rod ties the axle to the chassis and controls side...

Layshaft Bearing for the front of the LT77 five-speed manual gearbox layshaft. The bearing supports the forward end of the layshaft (countershaft)...

JATE Ring Recovery Points - heavy-duty steel rings that replace the original chassis lashing eyes to provide rated vehicle recovery points. The JA...

Fitment:  Defender van 1994 tot 2007 Discovery 1 van 1989 tot 1994 Range rover Classic

Hydraulic Bump Stop Mounting Kit - Front is the front-axle mounting hardware for a hydraulic bump stop installation, sitting within the suspension ...

Rear Top Shock Mount Relocator - repositions the upper rear shock absorber mounting 50 mm (2 in) lower on the chassis. Dropping the top mount incr...

Cranked Rear Radius Arm - links the rear axle to the chassis, controlling fore-and-aft axle location and reacting drive and braking torque. The cr...

Terrafirma rear spring retaining plates 90/D1/RRC

Spring Dislocation Cones - Front are fitted inside the front coil springs to prevent spring dislocation under maximum suspension droop. During extr...

Rear Shock Absorber damps the rear suspension within the suspension assembly, valved for a +2" (50mm) raised ride height. Offers 8-stage adjustabl...

Front Shock Absorber damps the front suspension within the suspension assembly, valved for a +2" (50mm) raised ride height. Fitted with a remote r...

Hydraulic Bump Stop & Mounting Kit is a complete progressive end-of-travel control package for the suspension, combining four hydraulic bump st...

Terrafirma 2"" pro sport mini dislocation kit for 90/D1/RRC

Shock Absorber - front suspension damper with four-stage adjustable damping, sized for +2 inch raised ride height. Fitted between the chassis and ...

Rear Shock Absorber for the rear axle suspension, damping spring oscillation and controlling vertical wheel movement between the rear axle housing ...

Front Shock Absorber for the front axle suspension, damping spring oscillation and controlling vertical wheel movement between the front axle housi...

Alloy Wheel from the Maxtrac Blindo range, finished in anthracite. Specifications: Size: 16 x 7 inches Bolt pattern (PCD): 5 x 165 Offset (E...

Hex Bolt, grade 8.8, M8 x 20mm. A standard metric hexagon head bolt. Grade 8.8 indicates a tensile strength of 800 MPa and a yield strength of 640...

Synchro Unit - the 1st/2nd gear synchromesh assembly carried on the mainshaft of the LT77 five-speed manual gearbox. The synchro hub is splined to...

Differential Gear Kit is a set of differential gears for the Rover-type axle differential, in the 10-spline configuration. The differential gears ...

Mainshaft for the LT77 five-speed manual gearbox, Suffix H specification. The mainshaft is the gearbox output shaft. It carries the synchroniser h...

Fusible Link is a sacrificial circuit-protection device used in the vehicle electrical system. Rated at 60A and identified by its yellow body, it ...

Water Pump for the engine cooling circuit, belt-driven from the front of the engine. The pump circulates coolant through the cylinder block, heads...

Exhaust Valve for the cylinder head valvetrain of the 3.5 V8 petrol engine. The exhaust valve opens to release burnt gases into the exhaust port a...

Inlet Valve for the cylinder head valvetrain of the 3.5 V8 carburettor petrol engine. The inlet valve seals the intake port against combustion pre...

Piston Assembly for the 2.5L 200 TDi turbo diesel, forming part of the piston and connecting-rod assembly within the cylinder block. The piston tr...

scew hexagonal head M6 x 45mm 4-speed LT95 and 5-speed gearbox bottom cover plate (with Rover V8 engine)

Screw used as a body and underbody fixing across several assemblies, including the tailboard striker, the folding side-door step assembly, and the ...

Hex Nut

Tow Ball & Pin Hitch Assembly for the towing system, mounting to the rear towing bracket. The assembly combines a tow ball for standard ball-c...

Wiring Connector for the chassis wiring harness, used in the fuel tank circuitry. The connector forms a serviceable electrical junction between ha...

Piston Ring Set for the 3.9 litre Rover V8, supplied at standard size and covering one piston - eight sets are required to do a complete engine. T...

Sealing Washer - bonded (Dowty-type) seal for the power steering pump banjo union. The washer is a metal outer ring with a vulcanised elastomeric ...

Regulator & Brush Assembly - the combined voltage regulator and brush box fitted to Lucas alternators in the charging circuit. The unit mounts...

Steering Box Race Bearing for the worm and valve assembly of the Adwest power-steering box. The race carries the worm shaft within the recirculati...