Range Rover Parts

Fuel Tank Mount is a rubber mounting that supports the fuel tank on the chassis. It cushions the tank on its mounting bracket, isolating it from c...

Oil Pressure Switch threads into the engine block oil gallery and monitors lubrication system pressure. It operates the low oil pressure warning l...

Transfer Box Output Flange Oil Seal is a radial shaft seal fitted at the output flange of the LT230 transfer box, sealing between the rotating outp...

Flanged Locking Nut, M10. General-purpose threaded fastener. The integral flange spreads the clamp load over a wider bearing area, removing the ne...

Fitment All TD5 diesel models up to (VIN) 6A999999 All TD5 diesel models All V8 EFi petrol models 2.5L 6 Cyl BMW Diesel /4.0L and 4.6L EFI V8 P...

Hydraulic Tappet fitted within the V8 petrol engine valve train, where it maintains zero valve clearance automatically. Engine oil pressure fills ...

Washer Non-Return Valve for the windscreen wash/wipe system. The valve is fitted into the washer fluid line between the pump and the jets. It perm...

Nyloc Nut - M12

Front Hub Assembly, ABS configuration. Part of the front axle hub and bearing system. The hub locates the front wheel and carries it for rotation ...

Inside Door Handle Bezel The interior trim escutcheon that surrounds the door release handle on the inner door panel, finishing the opening around ...

Exhaust Mounting Rubber - flexible support that suspends the silencer section of the exhaust system from the vehicle underbody. The moulded rubber...

Fuel Filter with a paper filter element, for carburettor petrol engines. Part of the fuel supply system. The filter is plumbed inline between the ...

Coolant Hose for the water pump circuit on the 3.5L V8 Twin Carb petrol engine. This hose connects the water pump outlet to the coolant pipe, rout...

LT230 Intermediate Shaft O-Ring, sealing the intermediate shaft within the LT230 two-speed transfer box main casing. The intermediate shaft transm...

Drain Plug - a tapered threaded plug used to seal and drain fluid from engine and driveline housings. It serves as a coolant drain plug in the cyl...

Flywheel Housing O-Ring - a sealing ring at the rear of the engine where the flywheel housing meets the cylinder block. Fitted to the 2.25L engine...

Thermostat for the 2.5L 200TDi diesel engine, operating within the thermostat housing at the top of the cooling circuit. This thermostat opens at ...

oil filter OEM Hengst Fits: - Defender Puma 2.2L - Defender Puma 2.4L - Discovery Sport 2.2L D 16V - Freelander2 2.2L D 16V - Range Rover Evoque 2...

Clutch Fork Clip secures the clutch arm rod to the release fork inside the gearbox bellhousing on LT77, LT85, and R380 5-speed manual gearboxes. T...

Needle Roller Bearing for the front axle swivel pin housing. The bearing seats in the swivel housing bore and carries the stub axle, providing rad...

Steering Box Seal Kit - Sector Shaft

Bottom Overhaul Gasket Set for the 3.5 V8 petrol engine. The set supplies the gaskets and seals used to reseal the lower engine once the sump is r...

Pop Rivet (blind rivet) for fastening panels, trim and brackets where access is only available from one side. The rivet is fitted into a drilled h...

Brake Hose - flexible hydraulic line in the rear braking circuit, connecting the chassis-mounted rigid brake pipe to the rear axle brake assembly. ...

Stub axle

Split Pin

Gearbox Filter for the LT77 five-speed manual gearbox. This gauze oil strainer sits in the gearbox lubrication circuit, screening the oil drawn thr...

Oil Seal for the LT230 transfer box input shaft. Part of the transfer box gear train. The seal fits around the rotating input shaft where it enter...

Automatic Drive Belt Tensioner for the front-end accessory drive system, maintaining correct tension across the auxiliary belt that drives the alte...

Nut - M6 is a plain M6 hexagonal nut used as a general-purpose threaded fastener throughout the chassis, body and mechanical assemblies. It tighte...

Joint washer

Oil Drain Plug threads into the drain port at the base of the engine sump, sealing the oil pan against leakage during operation. It sits within the...

Joint Washer - 4-Wheel ABS installed at the stub axle interface in the hub assembly of vehicles equipped with 4-wheel ABS. This asbestos-free gask...

Gear Lever Knob for the LT77 5-speed manual gearbox. Fits the main gear lever of LT77-equipped vehicles, including V8 petrol manual variants. The ...

Electric Fuel Pump mounted externally in the fuel supply system, drawing petrol from the tank and delivering it to the carburettor. This is an ext...

Courtesy Lamp Switch is the door-pillar plunger switch in the interior lighting circuit. Mounted in the door aperture, it is released when a door ...

Front Axle CV Joint, 24-spline, for the front drive shaft. The constant velocity joint sits at the outer end of the front axle shaft and transmits ...

Ignition Coil - high-tension coil in the ignition system. Converts the low-voltage supply into the high-tension voltage required to fire the spark...

Nyloc Nut with a 3/4" UNF thread, used as a locknut on heavy suspension joints. A nylon insert set into the crown of the nut deforms over the bolt...

Radius Arm Cup Washer is the dished washer used at the front radius arm mounting, seating against the radius arm bush to spread the clamping load o...

Flange Bolt securing the rear output (propshaft) drive flange to the output shaft of the LT230 transfer box. Manufactured to a high-tensile specif...

Drive Belt - 10mm × 1025mm for the auxiliary drive system on the 2.5L 4-Cylinder diesel and 200TDi engines. This poly-V ribbed belt drives the alt...

O-Ring for the oil filter adaptor assembly on 4-cylinder petrol and diesel engines up to and including the 300TDi. This O-ring seals the joint bet...

Engine Mounting Rubber is a bonded rubber-to-metal isolator in the powertrain mounting assembly. It sits between the mounting bracket and the chass...

Fan belt OEM DAYCO 10mm wide, 1235mm long

Oil Seal for the front axle swivel pin housing. Seals the front driveshaft where it passes into the inner end of the swivel housing, retaining axl...

Shock Absorber Washer for the rear suspension, outer position. This washer fits over the rear shock absorber mounting, seating against the rubber ...

Capless Wedge Bulb, 12V 1.2W, for instrument, facia, clock and cigar-lighter illumination. The glass wedge base pushes directly into the panel hol...