Range Rover Parts

Plain Washer for M10 fasteners. A flat washer fitted under a bolt head or nut to distribute the clamping load across the joint face, spread bearin...

Crankshaft Timing Chain Sprocket The drive sprocket mounted on the nose of the crankshaft within the timing chain drive of the Rover V8 petrol engi...

Clutch Master Cylinder Overhaul Kit for rebuilding a CV-type master cylinder, allowing the worn internal components to be renewed without replacing...

Hex Nut, 7/16" UNF, plain steel. This full hex nut secures the door top to the door base on Series models and is used at other 7/16" UNF fixing po...

Flasher Relay controls the direction indicator and hazard warning lamp circuit, switching the lamps on and off at the regulated flash rate. It plu...

Bypass Hose for the engine cooling system of the 200 TDi diesel engine, connecting into the coolant pump. It carries coolant on the bypass route t...

Steering Box is the recirculating-ball power steering gear at the heart of the steering system, converting rotation of the steering column into the...

Lock Washer secures a threaded fastener against loosening under vibration and thermal cycling. Fitted beneath the nut or bolt head, it bites into ...

Brake Pipe Union - a female union fitting for 3/16" (4.75mm) hydraulic brake pipe, with an M10 x 1mm thread. Machined from brass, it threads onto ...

Wheel Nut - secures an alloy road wheel to the hub, forming the threaded clamping interface between the wheel and hub. It uses a wide-stud profile...

Oil Pressure Switch threads into the engine block oil gallery and monitors lubrication system pressure. It operates the low oil pressure warning l...

Lower Steering Column Universal Joint for the steering column assembly. This universal joint sits at the lower end of the steering shaft, transmitt...

Castle Nut (castellated nut) used to retain halfshafts, output shafts and differential pinion shafts in Land Rover axle and drivetrain assemblies. ...

Clutch Slave Cylinder for the hydraulic clutch release system, fitted to the LT77 and LT95 manual gearboxes. The cylinder receives hydraulic press...

Wiper Delay Relay for the front windscreen wiper circuit, controlling the intermittent (delay) wipe function. It times the pause between wipe cycl...

Self-Tapping Screw – No. 8 × 1/2 in is a general-purpose fastener used across body, trim and electrical fixings, such as lamp guards, wheelguards, ...

7" round LED headlamp 12/24V chrome 78W LHD (pair)

Clutch Kit is a matched three-piece clutch assembly for the 2.5L 200TDi and 300TDi turbo diesel engines with manual transmission. The kit renews t...

Hex-head bolt, 5/16" UNF thread, 1" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and sockets...

Spring Retainer secures the upper outer mounting of the rear coil spring and damper within the rear suspension assembly. It clamps the top of the ...

Clutch Slave Cylinder, part of the hydraulic clutch release circuit on manual transmission applications. Mounted at the clutch housing, it receive...

Brake Disc - Solid - Rear is the rear brake disc, mounting to the rear hub and providing the friction surface the brake pads clamp against during b...

Flanged Bolt, M10 x 30 mm. A metric bolt with an integral flange beneath the hexagon head that spreads clamping load over a wider area and helps re...

Speedometer Drive Gear for the LT230 transfer box, located on the rear output and driving the speedometer take-off. This is the 20-tooth gear, ide...

Handbrake Pull-Off Spring for the transmission-mounted drum handbrake assembly. This return spring retracts the brake shoes against the backplate ...

Copper Washer - copper sealing washer used at threaded and banjo unions in the engine oil circuit. Forms a soft metal-to-metal seal that crushes t...

Timing Cover Plate Gasket sealing the timing gear cover plate on the 300Tdi 2.5L four-cylinder turbo diesel engine. The gasket forms the joint bet...

Core Plug (Cup Type) for sealing the core holes left in the engine block casting after the sand cores are removed during manufacture. The cup-shap...

Interior Door Handle for the left-hand side. Part of the door latch and release mechanism. Mounted on the inner door, the handle operates the latc...

Headlamp Assembly for the front exterior lighting system, supplied as a pair. Each crystal-style halogen unit mounts in the front lighting housing...

Coolant Temperature Sensor threads into the engine coolant circuit and reports coolant temperature to the instrument and engine management systems....

Sedimentor Sealing Ring for the diesel fuel filter and sedimentor assembly. The sedimentor separates water and sediment from the diesel fuel befor...

Gearbox Front Cover Oil Seal for the manual gearbox front cover, sealing around the primary (input) shaft. Retains gearbox oil and excludes dirt a...

Coolant Expansion Tank Cap – the pressure-relief cap that seals the cooling system's expansion (header) tank. Rated to 15 psi, it holds the system...

O-Ring for the LT95 combined gearbox and transfer box. It seals one of the shaft and housing joints within the unit, retaining gear oil and prevent...

Locking plate

Front Cover Gasket sealing the engine front cover to the cylinder block on the V8 EFI petrol engine. The gasket forms the joint between the timing...

Spring Washer - M6 single-coil spring lock washer. Fitted beneath a nut or bolt head, the split single-coil section bears against the fastener to ...

Handbrake Shoe Set for the transmission handbrake. Part of the transfer-box-mounted drum parking brake. The shoes expand against the inside of the...

Pinion oil seal

Drain plug LT77 R380

Spark Plug Ignition component for the Rover V8 petrol engine. Threaded into the cylinder head, it carries the high-voltage current from the igniti...

Edge Clip - push-on edge clip that grips the flange of an interior trim panel, retaining both the panel and the wiring harness routed along its edg...

Water reservoir grommet rubber seal

Alternator - Lucas A127 type, 65 A output. Part of the charging system: driven by the auxiliary belt from the crankshaft pulley, it generates the c...

Rubber Head Plug closing a machined oil-way opening on the 200Tdi 2.5L four-cylinder turbo diesel engine. The rubber plug seals an oil gallery ope...

Coolant Temperature Sensor threads into the cylinder head and reports engine coolant temperature to the engine management system and the instrument...

Clutch Release Fork - Heavy-Duty is the pivoting lever in the clutch release mechanism that acts on the release bearing. Operated by the clutch sl...