Range Rover Parts

Clutch Kit is a matched three-piece clutch assembly for the 3.5L V8 petrol engine with manual transmission. The kit renews the complete clutch as ...

Key Fob Cover Kit provides a replacement outer cover for the remote key fob, renewing a housing that has become worn, cracked or faded. It restore...

Headlamp Mounting Gasket for the headlamp assembly. A rubber gasket that seats between the headlamp unit and the body aperture surround. It provid...

Pipe and Hose Retaining Clip - Engine is a small-bore clip used to retain pipes and hoses at multiple points across the engine bay and fuel system ...

Engine Coolant, pre-mixed for use in the engine cooling system. It circulates through the radiator, water pump and heater circuit to regulate opera...

Steering knuckle fulcrum bracket assembly used within the front axle swivel and steering knuckle pivot arrangement. The bracket forms the lower p...

Warning Bulb Switch (Red) for the facia auxiliary switch panel. Mounted in the upper facia switch bank, this illuminated switch carries an integra...

Bolt - a 3/8" UNC x 2-3/4" bolt securing the rocker shaft and its oil baffle plate to the cylinder head on the Rover V8 engine. It clamps the rock...

Flanged Screw - M6 × 12mm is a metric flanged-head fastener used in body, chassis, and electrical component assembly points on Land Rover vehicles....

ABS Accumulator - a hydraulic pressure storage vessel within the ABS brake booster assembly. The accumulator stores pre-charged brake fluid pressu...

Crankshaft Pulley Bolt & Washer for the 2.2L 16-valve turbo diesel (DW12), securing the crankshaft pulley to the nose of the crankshaft. The b...

Speedometer Angle Drive is a right-angle gear adapter fitted in the speedometer drive line, configured for the right-hand (RH) routing. It takes t...

Diff oil seal

Split Pin: a cotter pin that locks a slotted (castle) nut or retains a clevis pin. After fitting, its legs are bent back to stop the fastening work...

A-Frame Ball Joint Bracket forms the pivot connection at the apex of the rear axle A-frame linkage. It mounts to the rear axle housing and locates ...

Compressor Amk Version

Main Bearing Set for the 2.5L 4-cylinder engine (200 TDi, 300 TDi and the related 2.5 diesel and petrol units), supplied at standard size. The mai...

Oil filter element for the engine lubrication system within the Oil Cooler and Filter assembly. This cartridge-type element removes particulate c...

Reverse lamp switch LT85 V8

Indicator, Horn, and Headlamp Dip Stalk Switch for the steering column assembly. This combination stalk switch mounts on the steering column and i...

Headlamp Bowl Seal - the gasket that seals the 7-inch headlamp bowl against the surrounding body panel. Fitted around the lamp aperture, it closes...

Dislocation Cone - Rear Coil Spring for the rear coil spring seat assembly. When long-travel shock absorbers or lowered top-mount shock relocators...

Drive Belt is the poly-vee auxiliary drive belt for the 2.5L 200 TDi diesel engine. Driven from the crankshaft pulley, it transmits power to the p...

Coil Spring - Front - +2" Light Duty is a front suspension coil spring providing approximately 50mm (2 inches) of lift above the standard ride heig...

Shock Absorber Bush Kit for the mounting points of Terrafirma TS-series shock absorbers. The kit provides the hardware required to replace worn bu...

Return to Centre Steering Damper for installation within the steering linkage assembly. This unit mounts between the axle steering arms and the st...

Turret Securing Rings - Front are reinforcement rings that fit around the front shock absorber top mount aperture in the inner wing. They distribut...

Rocker Cover Gasket Set for the 2.5L VM turbo diesel engine, sealing the rocker cover to the cylinder head. The gasket seats between the rocker co...

Nut - 2BA, a small-diameter fastener in the British Association (BA) thread standard. 2BA refers to the No.2 size within the British Association t...

Fuel Tank Sender is the in-tank fuel level sensing unit within the fuel gauge circuit, for V8 applications. Mounted inside the fuel tank, a float ...

Blind Nutsert (M6) is a threaded insert that provides an M6 female thread in thin sheet metal or panels where the rear face is not accessible. It ...

Pull Ring for the rear seat lock release. It operates the split rear seat lock mechanism, releasing the seat squab so the backrest can be folded d...

Trim Pad Clip is a fastening clip used to secure interior trim pads to the bodyside and door structure. It locates into a pre-formed hole in the p...

Bolt and Washer - an M8 x 25 mm hexagonal-head bolt supplied with a washer. A general-purpose threaded fastener used at various fixing points on t...

Swivel Housing: - Classic Defender 90/110/127/130 upto KA930455 (upto and including 1993 modelyear) (NON-ABS) Axle Code 20L, 21L, 22L, 23L, - Disco...

Clevis pin

Half Shaft Shim - 0.75mm is a 0.75mm selective shim that fits on the outside of the axle driving member to set the endfloat of the half shaft withi...

Flange Bolt - M10 x 35mm flanged hex bolt used at a range of driveline and engine mounting points, including bell housing, flywheel and clutch, tra...

Cylinder Head Bolt for the 200TDi 2.5-litre direct-injection turbo diesel engine. It secures the cylinder head to the engine block, clamping the he...

Belt Tensioner for the V8 EFI petrol engine, part of the ancillary (serpentine) drive belt system. The tensioner pulley bears against the auxiliar...

Polyvee Belt 3.9V8 1253mm

Enhance the steering strength and responsiveness of your Land Rover Discovery 1 and Range Rover Classic with these heavy-duty steering arms. He...

Hexagon Bolt - an M16 x 100 mm high-tensile bolt, property class 10.9, used to secure the front radius arm. The 10.9 grade provides the high clamp...

Cap bolt

Instrument Voltage Stabiliser for the Range Rover Classic instrument cluster assembly. This component regulates the voltage supply to the instrume...

Bolt with a 3/8" UNC (Unified National Coarse) imperial thread and a 2" shank length. A hex-head fastener used in body, chassis and general assemb...

Relay

Pedal Box Pivot Bolt for the pedal box assembly, forming the pivot axis on which the brake or clutch pedal swings within its mounting bracket. The...