Range Rover Parts

Camshaft Bearing Set comprises the plain bearing shells that support the camshaft within the cylinder block of the four-cylinder engine. The beari...

Camshaft Bearing, the front bearing in which the camshaft front journal runs within the cylinder block. It supports the forward end of the camshaf...

Drive Screw with a round head, a general body and chassis fixing. The steep-helix thread lets the screw be driven into a pre-drilled hole with a h...

Crown Wheel Bolt secures the crown wheel (ring gear) to the differential carrier within the axle differential. Threaded 3/8 UNF and 1.1/8 inch lon...

Exhaust Flange forms a bolted joint in the exhaust system of the early 3.5L V8 petrol engine with single downpipes. It provides the sealing face w...

Front Door Hinge Set Screw secures the front door hinge to the body pillar and door within the door mounting hardware. It clamps the hinge leaf in...

Grommet fits the bonnet release and locking mechanism. It lines the panel aperture through which the bonnet release cable passes, sealing the open...

Bolt - 5/16" UNF x 3-3/4" A 5/16" UNF setbolt, 3-3/4" long, catalogued for use across several applications. Its uses include securing the timing/f...

Crankshaft Key locates the timing gear and crankshaft pulley on the crankshaft nose, fixing their angular position relative to the shaft. It trans...

Circlip An external retaining circlip for the gearbox primary pinion shaft. It seats in a machined groove on the shaft to retain the primary pinio...

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the big-end bearing shells that sit between the connecting rods and the cranks...

Pinion Bearing - 35 × 68.5mm, a tapered roller bearing installed on the Constant Mesh Pinion shaft within the LT77, R380, and LT95 manual gearboxes...

Air Spring for the front of the electronic air suspension system. The air spring takes the place of a conventional coil spring, using a flexible ru...

Fuel Filter Head is the housing top of the fuel filter assembly within the diesel fuel supply system, onto which the filter element mounts. The he...

Tow Bar Wiring Kit - a dedicated 13-pin towing electrics loom that links the vehicle's lighting and auxiliary circuits to a trailer or caravan conn...

Anti-Roll Bar Bush is the front mounting bush that locates the anti-roll bar to the chassis. It cradles the bar within its chassis mounting clamp,...

Thermostat Housing Seal for the engine cooling system, sealing the thermostat housing joint. Fitted between the thermostat housing and its mating ...

Brake Union Washer is a sealing washer for hydraulic brake line connections. It seals the joint at a brake pipe or flexible hose union, fitting be...

Air Filter element for the engine air cleaner housing. Seated in the air cleaner housing upstream of the mass air flow sensor and throttle body, t...

Taper Roller Bearing - the mainshaft bearing used in the LT77 and R380 five-speed manual gearboxes, located at the rear of the primary pinion where...

Ensure smooth and reliable transmission performance with ATF Dexron II, a high-quality automatic transmission fluid designed for Land Rover vehicle...

Bolt for the rear suspension. It secures the lower mounting of the rear shock absorber to the lower suspension arm, carrying the damper load as the...

Bulb and Holder Assembly - Clear for dashboard and switch panel illumination. The assembly consists of a small bulb pre-fitted into a plastic hold...

Self-Tapping Screw - Black is an M8 x 25mm self-tapping screw with a black finish. The self-tapping thread cuts its own mating thread as it is dri...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Tailgate Gas Strut for the upper tailgate lift assembly. A gas-filled telescopic strut that supports the weight of the upper tailgate as it is rai...

Taper Roller Bearing - outer pinion bearing in the differential final drive assembly. The drive pinion is carried on a pair of opposed taper rolle...

Exhaust Stud Nut for front exhaust system connections. This nut secures exhaust pipe sections to the manifold or downpipe studs, maintaining a gas...

Diff oil seal

Piston Ring Set - a ring set for one piston of the Rover V8 petrol engine. The set comprises the compression rings and the oil control ring that s...

Bleed Screw for the hydraulic braking system. This bleed screw (bleed nipple) is fitted to brake calipers or wheel cylinders to allow hydraulic fl...

Drag Link Ball Joint (Short) is a steering linkage joint fitted at the short end of the drag link, within the steering track-rod circuit. It forms...

Starter Motor - Defender TD4

Washer is a plain flat washer used as a general-purpose load-spreading fastening component, with a 6 mm internal diameter and a 15 mm outside diame...

Drive Shaft Oil Seal for the front and rear hub assemblies. This lip seal fits at the inboard end of the front and rear hub carriers, sealing axle...

Flange Bolt - M6 × 10mm is a metric flanged-head fastener used across a wide range of assembly points on Land Rover vehicles. The integrated flang...

Spherical Bush for the LT77 and R380 manual gearbox gearchange mechanism. It seats the spherical pivot at the base of the gear lever inside the re...

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

COIL IGNITION GEMS (bobineblok RR 4.6 V8) INTERMOTOR

Wiper Arm Pivot Nut Secures the wiper arm to the splined pivot spindle of the windscreen wiper mechanism. It threads onto the spindle where it emer...

Panhard Rod Bolt - M16 × 70mm flanged hexagonal head. This bolt secures the panhard rod at its mounting bracket, retaining the rod that locates th...

Flanged Bolt - M12 x 100 flanged fixing that secures the front radius arm to the axle. The integral flange head spreads the clamping load across th...

Oil Filter for the 2.7L TDV6 diesel engine, part of the engine lubrication circuit. A paper-element filter that removes wear particles and contami...

Bolt, M10 x 30mm, used to secure the upper mounting bracket of the suspension damper. It fastens the shock absorber upper mount bracket at the fro...

Sealing Washer for the cylinder block oil jet adaptor on the 2.5L 4-cylinder diesel engine. Seals the jet adaptor against the cylinder block. Fitt...

Relay - 20A 5-pin black micro-format relay for use in vehicle fuse and relay centres. The 5-pin configuration provides both normally-open and norm...

Indicator Bulb - amber replacement bulb for the exterior indicator lighting circuit. Installs into the indicator lamp housing and provides the amb...

Pinion Oil Seal for the rear differential, running on the drive pinion shaft. The seal sits where the pinion shaft enters the differential housing...