Range Rover Parts

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Trim Clip - push-type retainer used to secure exterior trim, body mouldings, bumper covers and splash shields to the body structure. The clip is p...

Nut FQA

Suspension Bush - Rear Lower, polyurethane, supplied as a set of two bushes with internal sleeves and installation grease for the axle-end mounting...

Plain Washer - Swivel Pin Housing is a flat washer used within the front axle swivel pin housing assembly. It seats beneath the housing fixing bolt...

Front suspension strut insulator is installed within the front suspension strut assembly, positioned between the shock absorber upper mounting poin...

Wiper Spindle Cap - outer cap for the windscreen wiper spindle, installed at the outer end of the spindle where it passes through the scuttle panel...

Body Aperture Harness Grommet for the wiring harness routing assembly. Rubber grommet installed in a body panel aperture to seal and protect wirin...

Cylinder Head Gasket seals the right-hand cylinder head to the engine block, sealing the combustion chambers and the coolant and oil galleries acro...

Exhaust Manifold Gasket seals the joint between the exhaust manifold and the cylinder head on the TDV8 3.6L V8 Turbo Diesel engine. This gasket pr...

Sensor - ABS

Fuel Feed Hose for the fuel supply circuit. This flexible hose carries fuel within the fuel delivery or evaporative emission system. On diesel app...

Protective Coating Kit - Tintable (4 L) for applying a durable, textured surface coating to body panels, underbody areas, wheel arches, load beds, ...

Viscous Fan Coupling - temperature-sensitive drive coupling between the water pump drive and the engine cooling fan. It modulates fan speed with u...

Mirror Ring Casing - RH Outer is the outer trim ring that surrounds the mirror glass carrier on the right-hand exterior door mirror assembly of the...

Clutch Master Cylinder for the clutch hydraulic circuit, installed at the pedal box. The cylinder converts mechanical clutch-pedal movement into h...

Screw for securing the engine wiring harness in Rover V8 petrol engine installations. Fastens harness clips and mounting brackets to the engine bl...

Clutch Slave Cylinder for the manual transmission clutch release hydraulic circuit. It is fed by the clutch master cylinder and mounts at the gearb...

Suspension Arm - Front Lower Rear - RH is the rearward lower control arm in the front multi-link suspension. It locates the lower end of the wheel ...

Fuse - 60A - high-current blade fuse for the main electrical protection circuits. Rated at 60 amps, this fuse protects high-draw circuits such as ...

Brake tube GENUINE LR

Screw - a fastener used to secure exterior body panels and trim, including body mouldings, front and rear bumper assemblies, radiator grille panels...

Door Latch for the front door, right-hand side, operating within the door lock control assembly. The latch engages the striker on the body aperture...

Exhaust Gas Temperature Sensor monitors exhaust gas temperature within the diesel after-treatment system, mounted in the exhaust line at the cataly...

Blower Motor for the heating and air conditioning system, left-hand drive (LHD) configuration. Electric motor and fan assembly that circulates air...

Layshaft Bearing is the layshaft taper roller bearing for the LT77 and R380 5-speed manual gearbox. Located in the gearbox centre plate, it suppor...

Brake Union - Blanking Plug, male thread, M10 x 1mm, short body. Used in the metric hydraulic brake circuit to blank off an unused or redundant po...

Roll Pin for Door Hinge on the Range Rover Classic. A small cylindrical spring pin that locates and retains components within the door hinge assem...

Ignition Coil Pack in the engine ignition system, generating the high-tension voltage that fires the spark plugs. Used on the distributorless V8 e...

Front Propshaft - Wide Angle, connecting the transfer case front output flange to the front axle differential input pinion. The wide angle joint d...

Circlip is a split retaining ring that locates on the reverse shaft of the LT95 gearbox. It seats into a machined groove to axially retain the rev...

Light Socket for the inspection lamp on Series Land Rover vehicles. This black bayonet-type bulb holder is used in the inspection lamp assembly, p...

Coupling Assembly - union fitting for the engine oil cooler pipe circuit. This union connects adjacent oil cooler pipe sections in the engine bay,...

Mainshaft Spacer - a spacer fitted to the gearbox mainshaft of the five-speed manual gearbox. It sets the axial position of the gears and bearings...

Mainshaft Nut Staked retaining nut securing the shaft assembly within the manual gearbox. Tightened and staked to lock the gearbox shaft component...

Shim

Headlamp Washer Non-Return Valve fitted in the headlamp washer fluid circuit, in the delivery line between the washer pump and the headlamp jet noz...

Rear Radius Arm Bush Kit - Chassis End, supplied as a set of four polyurethane bushes with retaining plates, inner sleeves, and installation grease...

Bush Kit - Front Radius Axle Arm End

Transmission Sealing Ring for the ZF 5-speed automatic transmission. It seals the fluid filter to the transmission and is renewed with the filter d...

Key Fob Battery - CR2032 3V lithium button cell for Land Rover remote central locking handsets. Fits directly into the remote key fob housing. Rep...

Shock absorber rear early style, two halve bushes in upper eye, fitted to bracket using a large washer and a split pin.

Shock Absorber for the front suspension — the hydraulic damper that controls spring movement at the front axle. The damper resists and slows the c...

Brake Pad Set - Rear - Less Springs is a replacement rear brake pad set for the rear axle disc brake assembly. The set is supplied without retainin...

Brake Pad Set - Front - friction pad set for the front brake caliper assembly, part of the foundation braking system. Supplied in the less-springs...

Shock Absorber Dis1/Range Rover Classic Rear

Rear Bumper End Cap for the left-hand end of the rear bumper assembly on the Range Rover Classic. Fits over the open end of the rear bumper tube, ...