Range Rover Parts

Oil Pressure Gauge for the instrument panel. It displays engine oil pressure, driven from the oil pressure sender on the engine's main oil gallery...

Vacuum Actuator O-Ring for the LT95 4-speed gearbox. This O-ring seals the vacuum actuator fitted to the LT95 transfer case mechanism, used on V8-p...

Front Caliper Fixing Bolt with 7/16 UNF thread, used to secure the front brake caliper to its mounting bracket. This bolt is a safety-critical fast...

Swivel Ball for the front axle swivel assembly. The swivel ball is the central spherical component around which the swivel housing rotates, enablin...

Front Brake Disc for the front axle braking system. This is a solid (non-vented) rotor with a diameter of 298 mm. Cross-references with Ferodo par...

Spring Pin for the LT95 four-speed gearbox, used in the gear selector mechanism. The hollow, sprung roll pin locates and retains selector componen...

Washer - a plain flat washer with a 10.5mm internal diameter, sized for M10 fasteners. It seats under a bolt head or nut to spread the clamping lo...

Tappet Guide (guide only) locates and retains the tappet roller assembly within the engine block, maintaining correct alignment of the tappet as it...

Door Lock Striker is part of the door locking assembly, mounted on the body aperture at the door pillar. The door latch engages the striker as the...

Brake Caliper Bolt secures the rear brake caliper to its mounting bracket within the rear braking assembly. It clamps the caliper body in position...

Crown Wheel Bolt with British Standard Fine (BSF) thread, used to secure the crown wheel to the differential carrier in early Land Rover axles. Tw...

Differential Crown Wheel Locking Tab is a tab washer used in the axle differential assembly to lock and retain the crown wheel bolts after tighteni...

Bolt with a 7/16" UNF thread, used as a fastener on the Rover V8 petrol engine.

Bolt - 5/16" UNF x 5/8" is a general-purpose hexagon-head set bolt in 5/16 UNF (Unified National Fine) thread, 5/8 inch in length. Used across engi...

Auxiliary Drive Belt for the 2.5L 6-cylinder BMW diesel engine in the Range Rover P38. This poly-V belt drives the ancillary accessory circuit - i...

Brake Disc - a front vented brake disc, the rotating friction surface the caliper pads clamp against to slow the vehicle. The internal vanes draw ...

Shock Absorber - Front - LH is the left-hand front damper in the air-suspension front corner. It controls the motion of the front suspension at th...

Shock Absorber - Front - RH is the right-hand front damper in the air-suspension front corner. It controls the motion of the front suspension at t...

Panhard Rod Bush from the front suspension's lateral location linkage. The Panhard rod controls sideways movement of the axle relative to the body...

Ball Joint - Front Suspension Arm is fitted at the outer end of the upper front suspension arm, forming the pivot between the arm and the steering ...

HT Ignition Lead - V8 - No.8 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition out...

HT Ignition Lead - No.7 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition output t...

HT Ignition Lead - No.6 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition output t...

HT Ignition Lead - No.5 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition output t...

HT Ignition Lead - No.4 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition output t...

HT Ignition Lead - No.2 Cylinder - high-tension ignition lead from the ignition coil and HT lead assembly, carrying the secondary ignition output t...

Rear Brake Pad Set for the rear disc brake assembly. These pads are installed in the rear brake caliper and press against the brake disc to delive...

pad foam OEM, eneregy absorbing. (Bij filter LR111341)

Service Kit bundles the filters, spark plugs and sump hardware required for a scheduled service of the 4.4L AJ-V8 and 4.2L supercharged V8 petrol e...

Automatic Transmission Oil Pump for the 4-speed automatic gearbox, part of the transmission's internal hydraulic system. The pump sits at the fron...

Transmission Oil Cooler Hose - Diesel ZF Automatic is a hydraulic hose forming part of the automatic transmission cooling circuit on the Range Rove...

A/C Condenser for the air conditioning refrigerant circuit, mounted at the front of the vehicle ahead of the engine radiator. The condenser receiv...

HT Lead for V8 petrol engines, part of the high-tension ignition circuit. The high-tension lead carries the ignition output to the spark plug. Sup...

Brake Pad Wear Warning Wire for the front brake pad wear-indication circuit. The sensor wire is routed into the friction material of the front bra...

Fastener is a fixing used to secure exterior body trim and finisher panels to the bodywork. It retains trim components such as plinths and finishe...

Pan Head Screw, M6 x 12mm. Metric pan head screw for use across a range of Land Rover body, chassis, and electrical assemblies.

Inlet Manifold Gasket for the inlet manifold to cylinder head joint on the M62 B44 4.4L V8 petrol engine. Seals each manifold runner against its c...

Plastic Washer - a plastic washer used at the radiator cowl (fan shroud) mounting in the cooling system. It sits under the fixing that secures the...

Kit caliper repair

Rear Lower Suspension Arm (Left-Hand) is a lower control arm in the rear independent suspension. It locates the rear hub carrier to the chassis su...

Brake Pad Wear Warning Wire for the rear brake pad wear-indication circuit. The sensor wire is routed into the friction material of the rear brake...

Oil Cooler O-Ring a sealing O-ring for the engine oil cooler pipe on 2.5L diesel applications. It seals the pipe connection within the oil cooler ...

Suspension Bolt - M16 x 98mm - Rear for the rear axle and suspension assembly. This M16 x 98mm metric fastener secures rear suspension components ...

Front Brake Pads Britpartxs

Flanged Hex Bolt, M12 x 70mm. Secures the front wheel hub assembly to the steering knuckle (upright) within the front suspension and hub assembly....

Brake Pipe - Rear is a rigid hydraulic line forming the fixed section of the rear brake circuit, carrying pressurised brake fluid from the chassis-...

Anti-Roll Bar Bush for the front suspension, locating the front anti-roll (stabiliser) bar to the body. The bush clamps around the bar and allows ...

Alternator serving the charging circuit of the 2.7L and 3.0L V6 diesel (TDV6) engine. Driven by the accessory drive belt, the alternator converts ...